How to Deal with Slightly Deformed Wheel Hubs?

Where are the turn signals located?

Turn signals are located on the left and right sides of the front and rear of the car. Some vehicles also have them on or below the left and right rearview mirrors. Turn signals are important indicator lights that are turned on when a motor vehicle turns to alert vehicles and pedestrians in front, behind, left, and right to pay attention. The turn signal tubes use xenon tubes, and the microcontroller controls the circuit, with left and right alternating flashes working continuously. Turn signal structure and principle: Turn signals use flashers to achieve light flashing. They can be mainly divided into three types: resistance wire type, capacitor type, and electronic type. Among them, the resistance wire type can be further divided into thermal wire type (electrothermal type) and vane type (bounce type), while the electronic type can be divided into hybrid type (with contact-type relays and electronic components) and fully electronic type (without relays). For example, the bounce-type flasher uses the principle of current thermal effect, with thermal expansion and contraction as the driving force, causing the spring plate to produce sudden movements to connect and disconnect the contacts, achieving light flashing. Correct use of turn signals: When a car reaches a general flat intersection, depending on the width of the road, the size of the traffic flow, and the current driving speed, the turn signal should be turned on in the direction of the turn at a distance of 30-10 meters from the intersection. For example, when turning right or changing lanes to the right, the right turn signal must be turned on; when turning left or changing lanes to the left, the left turn signal must be turned on. When turning into an intersection with guide lanes, the turn signal should be turned on before entering the guide lane. Turning it on too early may give the following car the illusion of "forgetting to turn off the turn signal," while turning it on too late may cause accidents due to insufficient reaction time for the following car or pedestrians. When a car enters or exits a roundabout, the corresponding turn signal should be turned on according to the direction of travel. When the traffic in the current lane is congested and a lane change is needed during driving, observe whether the adjacent lane is free through the rearview mirror. Without hindering the normal driving of vehicles in other lanes, the corresponding turn signal should be turned on in advance, and then the lane should be changed. When a car makes a U-turn, the left turn signal should be turned on, and attention should be paid to observing whether there are any oncoming vehicles in front or behind the car before making the U-turn. On road sections without marked solid center lines, when overtaking is needed, the left turn signal should be turned on and the horn should be sounded (except in no-horn zones). If being overtaken, the car should yield by moving to the right. When it is necessary to pull over and park during driving, the right turn signal should be turned on in advance, and attention should be paid to observing the traffic dynamics on the right rear of the car before pulling over. When leaving the parking spot, the left turn signal should be turned on in advance, and attention should be paid to observing the traffic dynamics on the left rear of the car before driving into the traffic lane.

6

2

Share

Steps for Starting Reverse Parking?

Keep the vehicle parallel to the baseline (ensure the front wheels are straight by checking the steering wheel and the left front wheel). Lift the clutch to the semi-engaged point, stabilize the clutch after starting, and slowly reverse; turn your head to observe the rear right door's triangular window, then quickly turn the steering wheel fully to the right. When observing through the left rearview mirror that the left body line is parallel to the left line of the parking space, quickly straighten the steering wheel to the left.

9

5

Share

How to Repair a Scratched Headlight?

Under such conditions, if there is no "scratch damage" or "cracking" and similar situations, there generally won't be excessive "marks" left on the headlight. For certain special plastic materials, you can use dedicated tools like sandpaper or a towel to "wipe" and observe the specific situation. Nowadays, better ABS engineering plastics are commonly used. Such headlights perform well in terms of high-temperature resistance, penetration, and resistance to their own light sources such as ultraviolet rays.

17

5

Share

Where is the water temperature gauge located on the Haval H6?

The water temperature gauge of the Haval H6 is located below the tachometer. The water temperature gauge displays the coolant temperature, helping the driver understand the vehicle's condition. When the water temperature is too high, the driver should stop and wait for it to return to normal before continuing to drive. Below are the reasons why the water temperature gauge may not move: 1. The power line of the water temperature gauge is broken; the heating coil of the water temperature gauge is burnt out; 2. The heating coil of the water temperature sensor is burnt out or the contacts are poorly connected; 3. The wiring of the water temperature sensor is faulty or broken; 4. The voltage regulator supplying stable power to the water temperature gauge circuit is damaged.

5

Share

What to Do If the Rearview Mirror Glass Falls Off?

Manually adjust the rearview mirror glass to its lowest position. At this point, you can see the engagement point between the glass and the rearview mirror glass driver. Insert a flat-head screwdriver into the engagement point. After inserting the flat-head screwdriver, gently pry it backward to separate the glass from the glass driver. If you need to keep the glass, make sure to hold it securely. First, connect the heating wire harness. The heating wire is not polarized, so it can be connected in any orientation. Ensure it is properly connected to avoid detachment, which could cause the heating function to fail.

3

2

Share

How to Operate a BMW for the First Time?

After entering the driver's seat, first adjust the angles and positions of the seat and steering wheel. The seat can be adjusted in multiple angles to ensure a comfortable driving posture. When the vehicle needs to start moving forward, shift the gear into "D" (Drive) and slowly release the brake to move forward. If you need to park for an extended period, shift the gear into "P" (Park), which is the parking gear. Shift the gear into "R" (Reverse), and the reverse lights will illuminate. Among the pedals below the driver's seat, the left one is the brake pedal, and the right one is the accelerator pedal—be sure to distinguish between them.

16

1

Share

How to Deal with Slightly Deformed Wheel Hubs?

Where are the turn signals located?

Steps for Starting Reverse Parking?

How to Repair a Scratched Headlight?

Where is the water temperature gauge located on the Haval H6?

What to Do If the Rearview Mirror Glass Falls Off?

How to Operate a BMW for the First Time?

How to Adjust the Rearview Mirror Button on a Volkswagen?

How to Check Traffic Violations for Large Vehicles?

How to Fix a Volkswagen Fan That's Not Spinning?

How to Remove a Rearview Camera?