···
Log in / Register

How to deal with rust spots on the car hood?

4 Answers
DelKai
07/29/25 1:11pm

Buy sandpaper to sand off the rust spots, then use a touch-up pen to cover the metal to prevent rust. Purchase a touch-up pen that matches the car paint color and spray it over the rust spots on the hood. The touch-up pen may have some color difference from the original car paint. If you mind, you can go to a 4S store or a large repair shop for restoration.

Was this review help?
8
3
Share
JosiahDella
08/14/25 3:03am

When I last found rust spots on the hood, I first wiped the surface clean with a damp cloth, then gently sanded off the rust with sandpaper—making sure to sand until the metal shines. After that, I thoroughly cleaned it with alcohol or rust remover, let the hood dry, and then applied an anti-rust primer—this step is crucial to prevent rust from recurring. Once the primer dried, I covered it with a touch-up pen or spray paint of the same color, applying multiple coats for even coverage, and finally added a layer of car wax to protect the paint. It’s best to park in the shade to avoid rainwater or bird droppings accumulating, as these can easily cause rust spots to spread. Regularly check the hood’s corners after washing the car, and clean any scratches or dust immediately—this kind of maintenance can save a lot on repair costs. DIY repairs may take time, but the tools are inexpensive—sandpaper and spray paint cost just a few bucks, much cheaper than going to a shop.

Was this review help?
19
3
Share
Expand All
StCody
10/09/25 8:22am

I just noticed rust spots popping up on my car hood, so I went and bought a bottle of rust remover spray, which only cost 20 bucks at the supermarket. Following the instructions, I sprayed it directly on the rust spots, waited five minutes for the chemicals to work, then wiped off the rust with a soft cloth—it came off easily in just a few wipes, super convenient. After that, I rinsed with water and dried it to prevent any chemical residue from corroding the paint. Then, I applied some cheap car body protective wax—this kind of wax costs around 10 bucks a bottle and lasts a long time. Remember, rust spots often start from small scratches, so it’s best to dry the hood after rain to prevent water stains from lingering. If the rust spreads over a large area, just take it to a car repair shop for quick treatment—don’t tough it out. Handling it yourself isn’t troublesome at all, the tools are readily available, and the results are pretty good—give it a try!

Was this review help?
15
2
Share
Expand All
AlinaAnn
11/23/25 2:49am

When rust spots appear on the car hood, I directly mix white vinegar and baking soda into a paste, apply it to the rust spots, and let it sit for half an hour. Then, I gently scrub off the rust with an old toothbrush—economical and eco-friendly. After rinsing with clean water and drying, I apply a bit of cooking oil for temporary rust prevention—the oil prevents the metal from contacting air. When parking, try to choose a garage or shaded area to reduce exposure to sun and rain, the main causes of rust. Don’t worry about small rust spots; if they spread significantly, then seek professional treatment to save money and time. DIY rust removal is a great way to protect the environment.

Was this review help?
7
1
Share
Expand All
More Forum Discussions

How to deal with sticky substances on the car body?

Use a hot towel soaked in soapy water to wipe, or you can also use household cleaning products with cleaning effects. Mix soap with a small amount of ammonia and turpentine to remove adhesive marks. Use sticky transparent tape to repeatedly stick and peel off, which can remove some surface residue. A little diluted sodium water can wipe it off easily, or paint thinner can also be used. You can use a hair dryer to dry it, and then gently scrape it off.
10
5
Share

How to jump-start an Audi Q5 battery?

First, open the engine hood of your car. There is a switch under the steering wheel, then open the front hood and locate the battery inside. First, connect the red cable to the positive terminal of the dead battery, then connect it to the positive terminal of the rescue vehicle. Next, connect the negative terminal of the rescue vehicle to the negative terminal of the dead battery. After starting the engine of the rescue vehicle and then starting the engine of the dead vehicle, first remove the positive cable, then remove the negative cable.
15
3
Share

How to set the audio equalizer for Audi Q5?

The treble and bass settings can be adjusted by rotating the push-and-turn control knob. The modified settings only apply to the currently active audio source. Press the push-and-turn control knob. Rotate the push-and-turn control knob left/right until the desired position is reached. Press the push-and-turn control knob again. Rotate the push-and-turn control knob left/right until the desired position is reached. All speakers in the vehicle are activated. Front: Only the front speakers in the vehicle are activated. Rear: Only the rear speakers in the vehicle are activated.
3
4
Share

Where is the spark plug located on the Baojun 730?

Location of the spark plug on the Baojun 730: The spark plug is installed on the side or top of the engine. In earlier models, spark plugs were connected to the distributor via ignition cables. However, over the past decade, most car engines have been updated to feature direct connections between the ignition coil and the spark plug. How spark plugs work: The spark plug's ground electrode is connected to the metal shell, which is threaded into the engine block via the cylinder head. The insulator primarily serves to isolate the metal shell from the central electrode. The terminal nut is the part of the spark plug that contacts the high-voltage coil. When current passes through the terminal nut and the central electrode, it ionizes the medium between the central electrode and the ground electrode, generating a spark that ignites the air-fuel mixture in the cylinder.
4
0
Share

How to Connect Phone Navigation in Audi?

Turn on the Bluetooth in the car and also enable the Bluetooth on your phone. Once Bluetooth is activated, use your phone to search for the car's Bluetooth. After finding the corresponding Bluetooth device, proceed to pair them. During pairing, you will need to enter a password, which is usually the default password. If you don't know the password, you can refer to the car manual. After entering the password, the pairing will be successful, and you can then use navigation on the car's computer system. If your phone and the car's navigation system are not compatible, further troubleshooting may be required.
10
1
Share

How to Fix a Broken Window Switch?

There is a button on the center console that prevents the windows from rolling up or down. When pressed, three window switches become inoperable. Press the button down to cut power, then press it again to release. Accumulated debris, such as small cards inserted into the window, can cause issues. In this case, simply visit a repair shop to have the door panel removed and cleaned. Aging or short-circuiting of the window regulator circuit can lead to switch failure. If the regulator itself is malfunctioning, replacement is necessary. It is recommended to visit a 4S shop for replacement.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.