How to Deal with Rust on Car Doors?

1 Answers
DiTyler
07/29/25 3:12pm
If rust is found on the car door, it should be treated promptly to prevent the rust from spreading. The treatment methods are as follows: Surface rust with small area: If the rust appears on the surface and covers a small area, you can use water sandpaper to grind off the rust and then spray a layer of anti-rust paint. Rust reaching the primer: If the rust has reached the primer, the rust needs to be ground off, followed by primer spraying, and then topcoat spraying. Severe rust with large areas of paint peeling: If the car door has severe rust with large areas of paint peeling, the rusted paint needs to be completely scraped off, filled and leveled with putty, and then painted after the putty hardens. Rust-through on the door: If the car door is rusted through, repair is generally not recommended as the effect is limited, and rust may reappear after some time. It is advisable to replace the door.
Was this review help?
1
3
Share
More Forum Discussions

What to Do When Engine Oil is 2 cm Above the Maximum Level?

If the engine oil exceeds the maximum level by two centimeters, you can drain or extract a small amount of oil. When adding engine oil, ensure that the oil level is between the min and max marks on the dipstick. Here is some additional information: 1. If the oil level exceeds the max mark, it will increase the resistance during engine operation. 2. Increased resistance during engine operation will lead to higher fuel consumption. 3. Overfilling with oil may damage the three-way catalytic converter. When adding oil, do not let the oil level fall below the min mark; adding too little is also not advisable. 4. If the oil level is below the min mark, it can cause poor lubrication in the engine. Engine oil is often referred to as the lifeblood of the engine, as it plays roles in lubrication, cooling, cleaning, and sealing. 5. Without engine oil, the engine cannot function properly. Before adding oil, refer to your vehicle's maintenance manual, which specifies the exact amount of oil required for the engine. Simply add the oil according to the specified capacity.
1
5
Share

Differences Between Tubeless Tires and Ordinary Tires

Specific differences between tubeless tires and ordinary tires are introduced as follows: 1. Tubeless tires have a longer lifespan than ordinary tires: Under normal conditions, a fully inflated tubeless tire can last 3-4 months, or even half a year, because tubeless tires have thicker sidewalls. Ordinary tires with inner tubes are more likely to be punctured by nails and other sharp objects compared to tubeless tires. 2. Tubeless tires have a certain self-sealing ability for punctures: Ordinary tires will quickly lose air when punctured, making it difficult to ride or push once the tire goes flat, and the inner tube is prone to wear. In contrast, tubeless tires have strong puncture resistance, with their surface made of high-quality rubber. After inflation, the external tension increases, creating a certain pressure on the inner surface, which enhances the self-sealing ability for punctures. Once punctured, tubeless tires do not deflate completely in an instant but can maintain air pressure for a certain period. 3. Tubeless tires take less time to repair than ordinary tires: A tubeless tire can be repaired in about two minutes, whereas an ordinary tire requires pulling out the inner tube, inspecting the puncture location, followed by sanding, patching the hole, and then reassembling and reinflating.
20
1
Share

What is the highway fuel consumption of the hybrid Accord?

The official combined fuel consumption of the Accord hybrid is 6-6.6L/100km. Here are the relevant details: 1. The actual fuel consumption varies depending on the driver's habits and road conditions. 2. The new model features a fresh design with a 'U'-shaped front grille and a near-fastback silhouette. Inside, the hybrid version retains the design of the new-generation fuel-powered Accord, with the key difference being the adoption of a push-button gear selector similar to the NSX, replacing the traditional gear lever for enhanced technological appeal. The car comes equipped with features like one-touch start, a multifunction leather steering wheel, a large dual-screen infotainment system, and a dashboard that displays battery capacity and energy recovery information. 3. The GAC Honda Accord hybrid is powered by Honda's third-generation i-MMD dual-motor hybrid system, which includes a new IPU (Intelligent Power Unit). The powertrain consists of a 2.0L Atkinson-cycle naturally aspirated engine, dual electric motors, an e-CVT transmission, a power control unit, and a lithium-ion battery.
9
3
Share

What is the general valve clearance value?

The standard valve clearance is as follows: 1. The clearance of the intake valve is generally within the range of 0.20mm to 0.25mm. 2. The clearance of the exhaust valve is larger than that of the intake valve side due to thermal expansion, so the clearance naturally needs to be larger, generally between 0.29mm and 0.35mm. Here are some related introductions: 1. If the valve clearance is too small, the engine may leak air due to the valve not closing tightly in the hot state, resulting in a decrease in power and even burning of the valve. 2. If the valve clearance is too large, it will cause impact noise between the transmission parts and between the valve and the valve seat, and accelerate wear. At the same time, it will also reduce the duration of the valve opening, worsening the cylinder's air intake and exhaust conditions.
5
2
Share

What is abnormal oil level in Audi?

This is a warning indicator, indicating an abnormal engine oil level. It is recommended to check the oil level through the system or the oil dipstick to consider adding or draining oil. Here is the relevant information: 1. The yellow oil warning light indicates that the computer has detected a low oil level, which could be due to insufficient oil or a faulty oil level sensor. If the red warning light appears, it means insufficient oil pressure. First, check if the oil pressure sensor is damaged. If not, inspect whether the oil pump intake is blocked, which may require removing the oil pan for inspection. 2. When the oil level in the engine oil pan is insufficient, friction between bearings and journals may result in poor lubrication due to the low oil quantity, accelerating wear and even leading to bearing seizure.
2
2
Share

Can a burned clutch disc still be covered under warranty?

The clutch is considered a wear-and-tear component. If it burns out during the warranty period and the failure is not due to human factors, it can still be covered under warranty. However, policies vary by manufacturer, and even different models from the same brand may have different lists of wear-and-tear components and warranty periods. If the clutch disc burns out due to improper operation by the driver during driving, the repair costs will be borne by the vehicle owner. A burned clutch disc can be disassembled and inspected by a service station to determine whether it was caused by manufacturing defects or improper operation. There are several reasons why a clutch disc may burn out: 1. Improper operation by the driver, such as excessive use of the semi-engaged clutch, which causes continuous friction between the clutch disc, pressure plate, and flywheel, generating high temperatures that can burn the clutch disc. 2. Sudden release of the clutch pedal by the driver, causing abrupt engagement of the clutch disc and pressure plate, which can easily lead to clutch disc disintegration or damage to the pressure plate surface. 3. Prolonged use or excessive mileage, resulting in natural aging and wear of the clutch disc. 4. Substandard clutch disc material, leading to premature failure.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.