How to Deal with Overheated Brake Pads During Continuous Downhill Driving?

1 Answers
HadleyLynn
07/30/25 7:45am
During continuous downhill driving, it is normal for brake pads to overheat as braking generates a significant amount of heat. This is a normal phenomenon, and the issue usually resolves after the vehicle cools down for a while. However, if the temperature becomes excessively high, it is necessary to inspect the braking system for potential issues. Relevant information is as follows: 1. Brake Disc: It rotates while the vehicle is in motion. The brake caliper clamps the brake disc to generate braking force, slowing down or stopping the vehicle when the brakes are applied. Brake discs offer effective braking performance and are easier to maintain compared to drum brakes. 2. Introduction: Braking systems include disc brakes, drum brakes, and air brakes. Older vehicles often feature front disc and rear drum brakes, while many modern vehicles use disc brakes on both front and rear wheels. Disc brakes dissipate heat better than drum brakes, reducing the likelihood of heat fade during high-speed braking, thus providing superior high-speed braking performance. However, their braking efficiency at low speeds or when cold is inferior to that of drum brakes.
Was this review help?
12
2
Share
More Forum Discussions

Is the Wuling Journey Front-Wheel Drive or Rear-Wheel Drive?

The Wuling Journey adopts a mid-engine, rear-wheel drive configuration, making it a rear-wheel-drive vehicle. Its advantages include superior acceleration and hill-climbing performance, enhanced load-bearing capacity, reduced noise and vibration in the front cabin, and a more comfortable rear passenger area. Rear-wheel drive offers better performance: Compared to front-wheel drive, rear-wheel-drive vehicles deliver greater effective traction power. During acceleration, the center of gravity shifts rearward, increasing the weight borne by the rear wheels. This reduces the likelihood of rear-wheel slippage, and with increased friction comes greater traction, resulting in superior acceleration performance compared to front-wheel drive. Rear-wheel-drive vehicles provide stronger grip: In this setup, the rear wheels handle longitudinal forces while the front wheels focus solely on steering and providing lateral force. Even with the same center of gravity, rear-wheel-drive vehicles allow the front wheels to achieve greater lateral grip. Consequently, front-wheel-drive vehicles have significantly lower performance limits compared to rear-wheel-drive models.
9
4
Share

What are the body dimensions of the CR-V and Tiguan L?

Body dimensions of the CR-V and Tiguan L: The latest top-end version of the Tiguan L measures 4716(mm) in length, 1859(mm) in width, and 1677(mm) in height, with a wheelbase of 2791(mm). The latest top-end version of the Honda CR-V measures 4621(mm) in length, 1855(mm) in width, and 1689(mm) in height, with a wheelbase of 2660(mm). Powertrain specifications: The CR-V is equipped with a 1.5T engine, delivering a maximum power of 193 horsepower and a maximum torque of 243 N·m, paired with a CVT transmission. The Tiguan L is equipped with a 2.0T engine, delivering a maximum power of 186 horsepower and a maximum torque of 320 N·m. Exterior design: The Tiguan L has larger body dimensions, giving it a more imposing appearance, while the CR-V features a more stylish and sporty design, each with its own unique characteristics.
9
3
Share

What brand of tire is GOODRIDE?

GOODRIDE is the Goodride tire brand, established in 1997. Like the Chaoyang tire, it is owned by Hangzhou Zhongce Rubber Co., Ltd. The difference between Goodride and Chaoyang is that Goodride's products are more affordable than Chaoyang's. Introduction to GOODRIDE tires: 1. Tire types: There are car tires specifically developed for car users. Among them, the SA37 tire, designed for mid-to-high-end cars with excellent sports handling, meets the standards of mainstream European products; the SA07, a high-performance tire developed for mid-to-high-end cars that combines sportiness and comfort, features a newly developed low rolling resistance tread and is also very fuel-efficient; 2. SA37 tire: The SA37 is a high-performance car tire that uses a Random polymer high-silica formula, which can effectively break through the water film and improve the tire's wet skid resistance. It adopts an asymmetric tread pattern design, with fine grooves on the inside that can effectively break through the water film, increasing the contact area between the tire and the ground. The outside uses a large shoulder rib design, which can effectively reduce the creep between the ribs, thereby improving the accuracy of handling.
4
5
Share

What does Buick trouble code p2138 mean?

Buick trouble code p2138 indicates a throttle/accelerator pedal position sensor malfunction. Below is a detailed introduction to automotive fault codes: 1. Meaning: Represents the monitored fault system - P for powertrain; B for body system; C for chassis system; U for network or data communication transmission system fault codes. 2. First digit: Indicates whether it's a generic code (applicable to all vehicle manufacturers) or a manufacturer-specific code. For example: 0 refers to a generic code, 1 refers to a manufacturer-specific code. General Motors in the U.S. has specific numeric type codes to assist in diagnosing vehicle technical conditions. 3. Second digit: Identifies the type of affected fault system, with numbers ranging from 1-7: 1 for fuel and air metering system; 2 for fuel and air metering system (specifically for injection system circuit malfunction); 3 for ignition system or misfire monitoring system; 4 for auxiliary emission system; 5 for speed control and idle control system; 6 for computer output circuit system; 7 for transmission.
10
2
Share

What Causes the Malibu Steering Wheel to Not Move?

The car can start but the steering wheel does not move indicates an issue with the steering lock. The steering lock is controlled by the key. When the key is turned off, a locking pin engages the steering column, preventing the steering wheel from turning. If the steering wheel can turn but feels very heavy, it suggests a failure in the power steering system. Steering Wheel Technique: First, it is important to adopt a safe hand position on the steering wheel. Place your left hand near the 9 o'clock position and your right hand near the 3 o'clock position. Grip the wheel firmly but avoid excessive tension. Thumbs should rest naturally on the wheel. When turning the steering wheel, alternate your hands smoothly. For a full rotation, the left hand turns halfway, followed immediately by the right hand to continue the motion. Principle of the Steering Wheel: A rack-and-pinion gear set is enclosed in a metal tube, with the teeth of the rack protruding outside the tube and connected by tie rods. The pinion gear is attached to the steering shaft. When the steering wheel is turned, the pinion rotates, driving the rack to move. The tie rods at each end of the rack connect to the steering arms on the steering axle.
4
0
Share

What is Cold Bending Performance?

It refers to the ability of metal materials to withstand bending at room temperature without cracking. Below is a detailed introduction to cold bending performance: 1. Definition: Cold bending performance refers to the capability of steel to endure bending deformation at room temperature, which is an important process property of steel. The cold bending test can reflect the plastic deformation at the bending point of the specimen and reveal whether there are defects such as uneven internal structure, internal stress, and inclusions in the steel. 2. Standards: The qualified standard for the cold bending performance of steel bars is that after bending under the specified bending diameter D and cold bending angle α, there should be no cracks, scaling, or fractures at the bending point. According to the technical standards for steel bars, the values of D and α vary for different types of steel bars. For example, for Grade 335 crescent ribbed steel bars, α=180°. When the diameter is not greater than 25mm, the bending diameter D=2d; when the diameter d is greater than 25mm, the bending diameter D=3d.
12
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.