How to Deal with Mice in the Car Engine Compartment?

How to Solve the Problem of Frequent Stalling During Hill Start in Subject 2?

The solution to frequent stalling during hill start in Subject 2 is to master brake-assisted starting and precise clutch control. Each stall deducts 10 points, and some candidates fail because they don't brake in time, causing the car to roll back more than 30cm. If the car stalls during the test, don't panic—it only deducts 10 points and doesn't result in immediate failure, leaving room for recovery. Below are some key points to note for the Subject 2 test: 1. Adjust the seat properly: Before starting, adjust the seat and fasten the seatbelt before fingerprint verification. 2. Follow test rules: Each test section is monitored by GPS, and the control line (yellow dotted line) marks the test area. Once the front of the car crosses the control line, the test begins, and the rules must be followed strictly. 3. Correct mistakes promptly: If an error occurs, correct it immediately to ensure accuracy and minimize point deductions.

14

1

Share

Where is the car accelerator located?

The car accelerator is installed beneath the throttle pedal. Here are some details about the accelerator: 1. Amplifying throttle signal to enhance static response: The so-called 'acceleration' of an electronic throttle accelerator is primarily achieved by increasing throttle response sensitivity, amplifying the input throttle signal by 50%. 2. Amplifying throttle signal rate to improve dynamic response: When the throttle pedal is pressed, the accelerator calculates the rate of change in the throttle signal based on the degree and duration of the press. The faster the change, the stronger the acceleration demand. The throttle accelerator will then amplify this rate of change, ultimately resulting in better dynamic response during acceleration.

12

1

Share

What does the 6x4 drive configuration mean?

Drive configuration 6x4 indicates that the vehicle has six wheels, with four of them being drive wheels. The drive configuration of trucks is typically represented by the total number of wheels multiplied by the number of drive wheels. The number before 'x' represents the number of tire (groups), and the number after 'x' represents the number of drive wheel (groups). Below is a related introduction: Introduction to the 6x4 drive configuration: 6x4: A common arrangement for many heavy-duty trucks. One front axle is a steering support axle, and two rear axles are drive axles. An axle, also known as a shaft, is connected to the frame or load-bearing body via suspension, with wheels installed at both ends. Its function is to transmit forces and moments between the frame or load-bearing body and the wheels in all directions. The control device of the traction control system is a computer that monitors the speed of all four wheels and the steering angle of the steering wheel. When the vehicle accelerates, if the computer detects a significant speed difference between the drive wheels and non-drive wheels, it immediately determines excessive driving force and sends a signal to reduce the engine's fuel supply, thereby lowering the driving force and reducing the slip rate of the drive wheels. Advantages of the 6x4 drive configuration: The advantage of the 6x4 drive configuration is having four drive wheels, which provides stronger driving force and better road adaptability, especially on slippery surfaces like winter snow and rain, enhancing vehicle stability and reducing the risk of skidding or loss of control. The downside is that on roads with good conditions, tire wear and fuel consumption are relatively higher. The drive axles are also heavier and more complex in structure compared to load-bearing axles, resulting in a higher vehicle weight and purchase cost.

19

5

Share

What are the differences between escape1 and escape2?

1. Transmission components: Escape2 uses an 8-speed M310 groupset with an aftermarket chainring. Escape1 uses a complete Shimano groupset with M370 front derailleur, M430 rear derailleur, M391 chainring, and M355 hydraulic disc brakes, which is one level higher than Escape2's configuration. 2. Cost-performance ratio: Escape2 offers better value for money. For beginners, Escape2 is recommended. During continuous riding and learning, you can upgrade the bike according to your actual needs.

15

2

Share

What is automotive glass?

Automotive glass refers to specialized glass used in vehicles. The production of automotive glass involves heating the glass to near its softening temperature in a heating furnace, then rapidly transferring it to cooling grids with varying intensities for uneven cooling. This process creates different stress levels between the main viewing area and the peripheral areas of the glass, typically resulting in zone-tempered glass. Laminated glass is a type of glass product made by bonding two or more layers of glass with one or more layers of transparent adhesive material. Characteristics of laminated glass include: high impact resistance—when impacted, the brittle glass may shatter, but due to its combination with elastic PVB, the laminated glass maintains high penetration resistance and visibility. Strong adhesion—the glass and PVB are tightly bonded, so when the glass breaks, the fragments remain adhered to the PVB, preventing injuries and ensuring safety. It is also resistant to light, heat, moisture, and cold. Automotive glass maintenance methods: Use dedicated or suitable wiper blades and replace them regularly (usually once a year) to avoid scratching the windshield. Keep the windshield clean. If debris is stuck, avoid using the wipers and remove it with a towel instead. Use automotive-specific glass cleaner to maintain a smooth surface and reduce wear on the windshield. Before using the wipers during rain, wipe off dust and other particles to prevent scratching the windshield. When attaching labels or stickers to the windshield, use static cling films to avoid damaging the glass when removing adhesives. When parking outdoors in winter, cover the windshield with items like a car cover or a few sheets of newspaper to protect it from frost damage.

13

2

Share

Is entering the license plate number alone sufficient for checking vehicle violations?

No. Simply entering the license plate number is insufficient for checking violations, as violation records are considered personal information. To prevent unauthorized access, in addition to the license plate number, you must also input the engine number or vehicle identification number (VIN), both of which can be found on the vehicle's registration certificate. Additional relevant information is as follows: After a violation: It is recommended that vehicle owners wait at least three days before checking. Violation photos require manual review by traffic police and subsequent information upload and release. According to relevant regulations, the review of violations captured by electronic monitoring systems must be completed within ten days, and the data should be uploaded to the database within three working days for vehicle owners to access. Note: If no violation is found after ten days, the likelihood of a violation is minimal. If the electronic eye does capture a violation, the mobile phone number registered with the vehicle management office will receive a notification. Vehicle owners only need to follow the instructions in the SMS notification to address the matter promptly.

5

1

Share

How to Deal with Mice in the Car Engine Compartment?

How to Solve the Problem of Frequent Stalling During Hill Start in Subject 2?

Where is the car accelerator located?

What does the 6x4 drive configuration mean?

What are the differences between escape1 and escape2?

What is automotive glass?

Is entering the license plate number alone sufficient for checking vehicle violations?

What is the detailed explanation of the tenth-generation Civic dashboard?

Why does the Camry's AUTO headlight turn on during the day?

What is the fuel tank capacity of the GLE?

What does 'Yield right to left, left to straight, turn to straight' mean?