···
Log in / Register

How to Deal with Loud Diesel Engine Noise?

4 Answers
VanGia
07/23/25 3:08pm
Methods to address loud diesel engine noise are as follows: 1. If the car has difficulty starting and the engine noise is loud, clean the fuel system and check if the idle speed motor has carbon deposits that need cleaning. 2. For ignition system issues, inspect the working condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or inadequate spark plug firing can also lead to such faults. Check if the spark plugs have excessive carbon buildup and replace them if necessary. 3. Unstable oil pressure. If you have already cleaned the engine carbon deposits, cleaned the throttle body, replaced the oil pads and spark plugs, but still notice body shaking at idle, it is recommended to visit a 4S shop to check the fuel supply pressure and the intake pressure sensor for normal operation. If the fuel pump supply pressure is abnormal or the intake pressure sensor values are incorrect or malfunctioning, it can cause body shaking. Check the oil pressure and replace components if necessary.
Was this review help?
7
3
Share
McNoah
08/10/25 11:06am
My diesel car has been running for two or three years, and recently the engine noise has become alarmingly loud, much worse than the usual humming. A friend suggested I check the engine oil, and I found that cheap oil was used during the last oil change, leading to poor combustion due to low-quality oil. I tightened the belts and screws myself, but the noise didn’t completely go away, so I took it to the repair shop. The mechanic said it might be due to clogged fuel injectors or an exhaust leak. After replacing the parts, it became much quieter. It’s important to use high-quality engine oil, avoid filling up with poor-quality diesel, and regularly clean the fuel system to prevent issues. Excessive noise can be distracting, especially on highways, which is particularly dangerous. It’s best to fix the problem early to prevent further damage and save on repair costs.
Was this review help?
20
2
Share
Expand All
KaiMarie
09/22/25 4:52am
Having driven diesel vehicles for over a decade, I've encountered plenty of noise issues. It's usually caused by loose engine mounts or worn components, such as problems with the crankshaft or gears. Back when I drove old trucks, sudden noise increases would prompt me to check the oil pump and filter – replacing dirty ones often brought immediate improvement. Don't overlook minor details; worn fan bearings or belts can also create significant noise. Persistent noise can increase fuel consumption and wear down the engine's core components. I make it a habit to service my vehicle every six months, using high-quality lubricants and ensuring proper sealing. Safety comes first – when noise becomes excessive, don't push your luck; seek professional diagnosis promptly to avoid major repairs.
Was this review help?
5
0
Share
Expand All
DelElizabeth
11/05/25 8:12am
I enjoy tinkering with my car. If the diesel engine is noisy, start by checking the simple things. See if there's enough fuel in the tank, as low fuel or poor-quality fuel can cause noise. Tighten any loose chassis bolts with a wrench. If the air filter is dirty, clean it and see if that helps. If the belts are old, replacing them yourself might reduce the noise. But don't mess with the internal parts. If the noise persists, take it to a repair shop—it might be a fuel injection system issue. Regular checks can prevent small problems from becoming big ones.
Was this review help?
10
4
Share
Expand All
More Forum Discussions

What does the yellow OFF light on the dashboard mean?

The yellow OFF light on the dashboard indicates that the auto start-stop function is turned off. The engine auto start-stop function is enabled by default. To disable the engine auto start-stop function, you need to press the auto start-stop button again. When the engine auto start-stop function is turned off, a small yellow light will illuminate on the button. If the engine auto start-stop function is activated, the yellow light on the button will turn off. Engine auto start-stop automatically shuts off the engine when the vehicle comes to a temporary stop (such as at a red light). When it's time to move forward again, the system automatically restarts the engine. Its English name is STOP & START, abbreviated as STT. The STT intelligent fuel-saving system is a set of systems that control engine start and stop. It works by equipping a traditional engine with an enhanced motor that has an idle start-stop function, allowing the engine to completely shut off when the vehicle meets the conditions for idling. When the vehicle needs to start moving again, the idle start-stop motor system quickly responds to the driver's start command, rapidly restarting the engine for seamless operation, thereby significantly reducing fuel consumption and exhaust emissions. How the start-stop system works: When the vehicle stops moving due to traffic congestion or at an intersection, the driver presses the brake pedal and shifts to neutral. At this point, the system automatically detects that the engine is idling and not in gear; the wheel speed sensors of the anti-lock system show zero; and the electronic battery sensor indicates there is enough energy for the next start. Once these three conditions are met, the engine automatically stops. When the traffic light turns green, the driver presses the clutch, and the "start-stop device" can be activated immediately, quickly restarting the engine.
4
4
Share

How to Clean Car Headlights?

Here are the methods for cleaning car headlights: 1. Remove surface dust: Wipe the headlights with a cloth as cleanly as possible; 2. Cover the edges of the headlights: Use tape to cover the edge areas of the headlights. Some cars only have fogging or hazing in certain areas, so you can also mask off the areas that don’t need repair to avoid unnecessary scratches; 3. Initial sanding: Wipe the headlights with a cloth as cleanly as possible. Soak a piece of 1000-grit sandpaper in cold water for 10 minutes, then evenly sand the headlight cover, moving back and forth in one direction while keeping the surface wet. Apply moderate pressure to avoid damaging the surrounding paint or trim; 4. Secondary sanding: Repeat the above process with 1500-grit sandpaper, but sand in a different direction (e.g., if the first pass was vertical, this time go horizontal). Continue to keep the sandpaper wet while sanding the entire area. After wiping clean, repeat the process multiple times with 2000-grit, 2500-grit, and 3000-grit sandpaper, each time sanding at a right angle to the previous direction; 5. Apply polish: Apply polish to the plastic cover and buff in a circular motion for about 10 minutes. Be careful with the pressure to avoid removing the paint. Continue until the surface regains its mirror-like shine and looks as good as new.
4
2
Share

What to Do When Brake Pad Rust Causes Car Tire to Lock Up?

Severe rust on brake pads can cause unevenness on the brake disc surface, leading to the phenomenon of the tire locking up. Below are the solutions: 1. Minor rust: If there is only slight rust on the surface, you can use continuous braking while driving to remove it. The friction between the brake pads and the brake disc will 'polish' the surface. 2. Multiple rust spots: If there are multiple rust spots, it is best to drive the car to a repair shop, remove the brake disc, and use sandpaper to clean off the rust. Ensure the brake pad surface is normal, then reassemble and conduct a road test. 3. Inspection method: Drive on a flat road at 70km/h and perform multiple brakes to ensure there are no abnormalities. If there is shaking, it indicates the brake disc surface is uneven, requiring further polishing or replacement as needed.
5
3
Share

Is Haval a Domestic Car Brand?

Haval is a domestic car brand. Haval is a brand under the Great Wall Motors Group, primarily manufacturing SUV models. Among them, the Haval H6 offers two modes: two-wheel drive and four-wheel drive, featuring a unibody construction. The Haval series mainly includes models like IF, M1, M2, M4, H2, H3, H5, H6, H7, H8, the all-electric SUV Haval E, and several practical pickup trucks. Regarding the Haval H6's drive system: The Haval H6 has two modes: two-wheel drive and four-wheel drive. The H6 is built on a completely new platform, different from the previous H3 and H5. Its most notable feature is the adoption of a unibody construction. The four-wheel-drive version of the H6 uses an on-demand four-wheel-drive system, unlike the body-on-frame construction + part-time four-wheel-drive system used in the H3 and H5. Regarding the Haval H6's powertrain: Early models of the Haval H6 were equipped with both gasoline and diesel engines. The gasoline engine has a displacement of 2.0L, with a maximum power of 133 horsepower and a maximum torque of 186 Nm. For the transmission, the gasoline version of the Haval H6 is paired with a 5-speed manual transmission. As for the diesel engine, the H6 uses the GW4D20 Green Static 2.0VGT engine, which is also used in the H5 model, with a maximum power of 150 horsepower and a maximum torque of 310 Nm. The diesel Haval H6 is equipped with a 6-speed manual transmission.
15
2
Share

What is the method for resetting the tire pressure monitoring system?

The method to reset the tire pressure warning light is to first start the vehicle, then press and hold the tire pressure monitoring reset button. Release the button after hearing a beep sound, at which point the current normal tire pressure data will be stored by the tire pressure monitoring system, and the previous data will be automatically cleared. Then, the fault light on the dashboard will turn off. Reasons for the tire pressure fault light to illuminate include: 1. Driving with low tire pressure for too long. 2. Tire pressure becoming low due to not being inflated for a long time. 3. A punctured tire. 4. Excessive tire pressure. The safest and most secure approach is to reset the tire pressure indicator only after ensuring that there are no tire faults.
17
0
Share

How to Clean Fabric Seats?

Methods for cleaning fabric seats: 1. Use specialized foam cleaner for cleaning. 2. If not very dirty, you can directly wipe with a damp cloth. 3. It is recommended to clean fabric seats regularly. If left uncleaned for a long time, fabric seats can become very dirty, making them harder to clean later. Here are some precautions for using fabric seats: 1. During regular car washes, you can ask the technician at the car wash shop to clean the fabric seats. Car wash shops have professional tools and can use a vacuum cleaner to clean the fabric seats. 2. Avoid spilling drinks on the fabric seats during daily use, as this can be difficult to clean. 3. Fabric seats offer good comfort and practicality, and generally, sharp objects cannot tear them.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.