How to Deal with Insufficient Power When Going Uphill in Subject 2?

1 Answers
FaithLynn
07/29/25 6:08pm
When facing insufficient power while going uphill in Subject 2, you can increase the vehicle's throttle to compensate for the lack of power. Below is a detailed explanation of how to handle insufficient power when going uphill in Subject 2: 1. Method of coordinating throttle and clutch in Subject 2 exam: Use the vehicle's clutch in conjunction with the brake to control the vehicle's speed, and apply throttle at the appropriate time. Otherwise, the vehicle may experience insufficient power, leading to stalling and resulting in failure of the Subject 2 exam. Especially during the uphill start in Subject 2, it is difficult to complete the test item if the vehicle does not apply throttle. 2. Reason for using the clutch to adjust speed in Subject 2 exam: The clutch can effectively control the vehicle's speed. Generally, the idle speed of driving school training vehicles is set relatively high. Using the throttle to control speed would increase the difficulty of the exam. This is designed to help students better complete the specified subjects.
Was this review help?
16
3
Share
More Forum Discussions

How Many Years Can Original Spark Plugs Last?

Under normal maintenance conditions, automotive spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the user manual. Refer to the following maintenance standards for replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the hood, lift the plastic cover of the engine, and remove the high-voltage ignition wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for external debris such as leaves or dust and ensure they are thoroughly cleaned. Place the new spark plugs into the spark plug holes, hand-tighten them a few turns, and then use the socket to tighten them further. Reinstall the high-voltage ignition wires in the firing order and secure the cover plate.
17
3
Share

How to Turn on the Heater in a Nissan Sylphy?

The method to turn on the heater in a Nissan Sylphy is as follows: 1. Press the knob with red and blue color buttons; 2. Wait for 5 to 10 minutes after ignition; 3. When the water temperature rises to the normal level, you can turn on the heater. Precautions for using the heater: 1. Wait for 8 to 15 minutes after the car starts until the water temperature reaches the normal level before turning on the heater; 2. Adjust the air conditioning circulation mode to internal circulation and set it to the heater mode, which is the red zone; 3. Do not turn on the air conditioning. The heater utilizes the car's own heat cycle to save energy. Adjust the fan speed and set the air conditioning to a suitable level to direct the airflow; 4. When parking for a long time, turn off the heater in time or roll down the window slightly to prevent carbon monoxide poisoning.
7
0
Share

What does ECO mean in a car?

ECO refers to the car's economical driving mode. It is an English abbreviation formed by combining Ecology (environmental protection), Conservation (energy saving), and Optimization (power). The Eco mode is further divided into active Eco driving mode and non-active Eco driving mode. When the Eco indicator light on the dashboard illuminates, it indicates that the vehicle's economical mode has been activated. Eco mode is categorized into active and non-active types. The difference lies in the fact that the active type has a dedicated button, allowing the driver to choose whether to enable it. When the driver presses the Eco mode switch, the dashboard indicator light immediately turns on, and the vehicle automatically begins adjusting settings such as throttle opening, transmission shift logic, and air conditioning output power. The non-active Eco mode does not have a dedicated button. When the Eco indicator light on the dashboard illuminates, it serves merely as a reminder function. The Eco system automatically evaluates your driving behavior. If your current driving operation achieves the optimal fuel supply, the dashboard will simultaneously display the Eco indicator light. Most cars adopt the active Eco driving mode, which means they have a dedicated switch button. Therefore, during daily driving, we can generally enable the Eco mode. However, it is unnecessary to activate Eco mode when driving at speeds exceeding 120 km/h, during idle parking, in N/P gear, or in manual mode, especially when climbing hills. Doing so would not only fail to demonstrate the fuel-saving characteristics of Eco mode but also negatively impact the vehicle's power performance. Additionally, the Eco mode typically becomes ineffective under the following circumstances: When the vehicle speed exceeds 120 kilometers per hour, the car prioritizes speed, causing the Eco mode to automatically deactivate. During idle parking or when in N/P gear or manual mode, the Eco mode may also become ineffective. When a high torque output is required, such as when climbing a hill, the engine control unit prioritizes ensuring sufficient power to drive the vehicle, and the Eco mode will not function in such scenarios.
20
4
Share

What does the circle with an exclamation mark on the car dashboard mean?

Red exclamation mark (specifically a circle with an exclamation mark inside parentheses), this represents a warning for the braking system, mainly indicating a brake system malfunction or low brake fluid level. Solution: Immediate inspection and repair of the braking system are required to avoid accidents. Apart from the red exclamation mark indicating a brake system fault, other exclamation marks on the car are yellow, representing general faults, automatic transmission faults, abnormal tire pressure, and lighting faults. Below is a detailed analysis of these four situations: General Fault: A triangle with an exclamation mark inside. If this symbol lights up, it indicates a general performance or component and function fault in the car. Main issues include parking sensor faults, fuel cutoff system intervention or malfunction, external light faults, engine oil pressure sensor faults, etc. It is necessary to go to a 4S shop for inspection to identify the source of the fault. Automatic Transmission Fault: A yellow gear with an exclamation mark inside. This is the automatic transmission fault warning light, indicating a transmission fault or transmission lubricant level below the normal range. Transmission oil should be replaced promptly. Abnormal Tire Pressure: A horizontal line under parentheses with an exclamation mark in the middle. This represents the tire pressure monitoring warning light. When the car's tire pressure is too low, this warning light will illuminate. Check the car's tire pressure and restore it to the normal range. Lighting Fault: A yellow bulb with an exclamation mark. This is the lighting fault indicator, indicating a fault in one of the car lights. Solution: Go to a 4S shop for inspection and repair as soon as possible, or perform a self-check. Focus on commonly used bulbs such as turn signals, fog lights, and interior lighting to identify the problem.
18
4
Share

What are the symptoms of a faulty clutch?

The symptoms of a faulty clutch are: 1. Clutch slippage. 2. Incomplete clutch disengagement. 3. Clutch shuddering. 4. Abnormal clutch noise. The clutch is located within the flywheel housing between the engine and the transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output shaft of the clutch is the input shaft of the transmission. Precautions for installing the clutch pressure plate: 1. The clutch pressure plate has 6 screw mounting holes, two of which are slightly larger with a small hole on each edge serving as positioning holes for the pressure plate. 2. It is strictly prohibited to touch the clutch pressure plate with oily hands, rags, or any oil-contaminated objects. 3. Check the fit between the splines of the driven plate hub and the input shaft splines to ensure there is no sticking or excessive play. 4. All bolts should be tightened to the specified torque, alternately and diagonally, in multiple stages. 5. Check the free clearance between the release bearing and the diaphragm spring or the free play of the clutch pedal.
11
2
Share

What is the correct parking operation for an automatic transmission?

Correct method for parking an automatic transmission vehicle: 1. Press the brake pedal to slow down and come to a complete stop. 2. After stopping, shift into N (Neutral) gear. 3. Engage the parking brake. 4. Release the foot brake and ensure the vehicle is stationary. 5. Press the foot brake again and shift into P (Park) gear. 6. Turn off the engine. Correct method for starting an automatic transmission vehicle: 1. Turn on the power supply, then start the engine. 2. After ignition, press the brake pedal, shift into D (Drive) gear, release the parking brake, and gently press the accelerator to start moving. 3. After starting, accelerate appropriately according to road conditions. Introduction to various gears in automatic transmission vehicles: 1. P stands for Park, used when parking. 2. R stands for Reverse, used when reversing. 3. N stands for Neutral, used when starting the engine. 4. D stands for Drive, used when the vehicle is moving forward. 5. L stands for Low, mostly used for climbing or descending slopes. 6. S is similar to 2nd gear, only shifting between 1st and 2nd gears.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.