How to Deal with Fogging on the Outside of the Car Windshield?

1 Answers
DelRichard
07/30/25 6:39am
Methods to deal with fogging on the outside of the car windshield include: 1. Open both windows to allow air convection and eliminate the temperature difference on both sides of the windshield; 2. Turn on the air conditioning with cold or hot air; 3. Use a defogging agent; 4. Wipe the glass with soapy water; 5. Dry the fog with a towel. The reasons for fogging on car glass are: 1. Large temperature difference between the inside and outside of the car; 2. The window temperature is lower than the dew point temperature; 3. There is a temperature difference on both sides of the window. Methods to maintain car glass include: 1. Use windshield washer fluid according to the season; 2. Apply car glass heat insulation film. Methods to clean car glass include: 1. Pour water from the top of the vehicle and wipe off the dirty water with a sponge; 2. Spray the glass cleaner solution evenly on the glass with a high-pressure spray bottle; 3. Carefully dry the moisture with a soft cloth.
Was this review help?
1
4
Share
More Forum Discussions

What Causes the Engine Fault Code for Misfire in Cylinder 3?

The main reasons are as follows: 1. Damage to external components: Mainly caused by components around the combustion chamber such as valves, valve seat rings, valve guides, and spark plugs. 2. Misfire due to the failure to ignite or delayed ignition of the air-fuel mixture in the cylinder: For the first scenario, it is usually recommended to check the spark plugs, clean the carbon deposits on the intake and exhaust valves, and inspect the turbocharger for any issues, such as wear or burning of the turbocharger impeller. For the second scenario, it is usually caused by an abnormality in a certain component or part, leading to unstable engine regulation by the ECU, which fails to meet the theoretical values calibrated by the ECU, resulting in misfire.
16
3
Share

Why does the Volkswagen transmission U0101 fail to start?

Volkswagen transmission trouble code U0101 causes the vehicle to fail to start due to loss of communication with the Transmission Control Module (TCM). Additional information: 1. Trouble code analysis: Modules connected to the high-speed GMLAN serial data circuit monitor serial data communication during normal vehicle operation. Operational information and commands are exchanged between modules. Pre-recorded information in the modules specifies which data needs to be transmitted between the serial data circuits of each virtual network. The receiver module monitors this information and uses some periodic messages as indicators of the transmitting module's operational status. The monitoring timeout is set at 250 milliseconds. Each message contains the identification number of the transmitting module. 2. Conditions for setting the diagnostic trouble code: The ignition switch is in the "Run" position, and communication with the transmission control module is lost for more than 12 seconds (scan cycle is 1 second). Actions taken when the diagnostic trouble code is set: For lost parameters, the module will use default values. Conditions for turning off the malfunction indicator lamp/clearing the diagnostic trouble code.
4
0
Share

Why is there a hissing sound after starting the car?

The reason for the hissing sound after starting the car is that there is damage or air leakage in the hose on the engine intake manifold. It should be repaired or replaced at a maintenance shop in time. The following is a related introduction to the intake manifold: 1. Meaning For carburetor or throttle body gasoline injection engines, the intake manifold refers to the intake pipe from the carburetor or throttle body to the intake port of the cylinder head. 2. Function: The function of the intake manifold is to distribute the air-fuel mixture from the carburetor or throttle body to the intake ports of each cylinder. For port fuel injection engines or diesel engines, the function of the intake manifold is only to distribute clean air to the intake ports of each cylinder.
12
3
Share

What are the reasons for the windshield washer fluid not spraying?

There may be several reasons why the windshield washer fluid does not spray: 1. The washer fluid level is too low: There is still water in the reservoir, but it does not reach the standard height, so it cannot spray. Try filling up the washer fluid. 2. The spray nozzle is clogged: If the spray nozzle is blocked by dust, the washer fluid cannot spray. Simply use a fine needle to clean the nozzle. 3. The washer fluid is frozen: In very low winter temperatures, the washer fluid may freeze. In this case, just park in a sunny area to let the fluid thaw naturally, then replace it with new antifreeze washer fluid. 4. Fuse or motor damage: If there is no sound from the motor when trying to spray the washer fluid, and the windshield wipers also do not work, then the issue may be a blown fuse or a damaged motor.
7
5
Share

How Long is the Battery Warranty for Volkswagen Tayron?

Volkswagen's new Magotan battery has a lifespan of 2-3 years, but as the car's electrical components age, the battery's load gradually increases, which may shorten its service life. Additional information about the battery is as follows: 1. Working Principle: When disconnecting the battery, always start with the negative terminal. Accidentally starting with the positive terminal may cause it to contact the vehicle's body ground, leading to a short circuit and damage to the car's electrical components. After removing the negative terminal, the vehicle's electrical system will be powered off, and the positive terminal can then be removed. Some high-end cars require the electrical system to remain powered during battery replacement, as disconnecting the battery may necessitate the use of a professional automotive diagnostic tool for decoding and matching. Therefore, before replacing the battery, it is essential to connect a backup battery in parallel with the car's battery (both terminals). 2. Precautions: Before installing a new battery, remove the old battery by detaching the mounting bracket or the bottom mounting bolts. Secure the battery bracket (tighten the bolts if there are bottom mounting bolts), install the positive terminal first, and cover it with the insulating sleeve. Then, install the negative terminal. At this point, the vehicle's electrical system is fully powered. After connecting both terminals, manually check if the battery terminals are securely fixed—they must not be loose. (Typically, repair shops apply petroleum jelly to the battery terminals after replacement to prevent oxidation and rust, which could affect conductivity and ease future removal.) Now, you can insert the key and start the engine to check for any abnormalities in the dashboard indicators. Usually, disconnecting the battery during replacement may cause some electrical components to malfunction temporarily, and the dashboard will display warning indicators.
11
2
Share

Can the car run normally in second gear without accelerating?

Second gear can allow the car to run normally without accelerating. Below is an introduction to gear shifting related content: 1. Shifting from first to second gear: The permissible range for first gear is 0-20 km/h, and shifting to second gear should occur at 15-20 km/h. 2. Shifting from second to third gear: The permissible range for second gear is 10-30 km/h, and shifting to third gear should occur at 25-30 km/h. 3. Shifting from third to fourth gear: The permissible range for third gear is 20-40 km/h, and shifting to fourth gear should occur at 35-40 km/h. 4. Shifting from fourth to fifth gear: The permissible range for fourth gear is 30-50 km/h, and shifting to fifth gear should occur at 45-50 km/h.
10
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.