How to Deal with Fog on the Outside of the Windshield?

2 Answers
OwenLee
07/25/25 2:37pm
Methods to deal with fog on the outside of the windshield: 1. Use the car's built-in air conditioning system by turning on the fan and cooling switch. The cold air will disperse the fog on the windshield. Besides using air conditioning for defogging, hot air can also serve the same purpose; 2. Open the windows to allow convection of cold and hot air. Crack the side windows slightly to facilitate air convection inside the car. As the interior temperature gradually matches the outside temperature, the fog will dissipate; 3. Use specialized anti-fog products. Spray evenly on the windows and wipe clean before use to form a transparent protective film on the glass, preventing fog formation. One application can last for half a month; 4. Use dish soap with a dry cloth. Mix dish soap with water at a ratio of 1:6, apply evenly on the car glass with a sponge, and wipe clean with a car towel after drying. This method leaves no watermarks and can effectively prevent fog for up to 20 hours.
Was this review help?
9
5
Share
AbigailAnn
08/11/25 9:11pm
When the windshield fogs up outside while driving, I find it quite annoying, but it's quite common in humid or cold weather. I immediately turn on the wipers to clear it, and they wipe it clean in an instant. The condition of the wiper blades is crucial, so it's important to replace old ones regularly. If the fogging persists after using the wipers, I switch the air conditioning to defrost mode, increase the airflow, and direct it toward the glass. This quickly dries out the moisture and keeps the view clear. For safety, never wait too long because fogged-up windows can impair driving vision and easily lead to accidents. I make it a habit to check the windshield washer fluid level in advance and avoid setting the car heater too high to reduce temperature differences. Paying attention to air circulation, such as opening the windows briefly for ventilation, can also prevent fog buildup.
Was this review help?
5
3
Share
Expand All
More Forum Discussions

Will Parking in First Gear for a Long Time Damage the Car?

Parking in first gear generally does not damage the car, but it is not recommended for long-term use. The hazards of parking in first gear include: 1. Safety risks: If the car is left in gear after parking and the clutch is not depressed when starting the car next time, the vehicle may lurch forward, potentially damaging the transmission gears. Transmissions are designed to operate in a neutral floating state, where the resistance to movement in any gear is roughly the same. Some shift levers use a cable design, and if left in a particular gear for a long time, it may cause prolonged stress in one direction, affecting the lifespan. 2. Engine damage: If the car is parked in first gear and the engine is off, a sudden external impact on the vehicle can transfer energy from the ground through the tires and axles, ultimately back-driving the engine. This sudden force can easily cause damage to the internal gears of the engine.
8
2
Share

How to Activate Cruise Control in Camry?

Toyota Camry's cruise control operation method is as follows: 1. Turn on the system: Press the power button to activate the system, at which point the cruise control indicator light on the dashboard will illuminate. 2. Accelerate: Accelerate to the desired speed, then press the SET button. At this point, you can release the accelerator pedal with your right foot, and the speed will be maintained at the current level. 3. Fine-tune speed: You can use the 'RES+' and 'SET-' buttons to make minor speed adjustments. 4. Deactivate cruise control: There are three ways to deactivate cruise control: press the brake pedal, press the cancel (CANCEL) button, or press the power (ON/OFF) button. 5. Resume cruise control: If cruise control was canceled by pressing the brake or cancel button, you can press the RES button to resume the previously set cruise control speed.
2
2
Share

What are the common problems with the 420 Xichai engine?

420 Xichai engine has the following common problems: 1. Coolant entering the fuel tank: The fuel-water separator turns green during operation, indicating a lack of coolant in the radiator. In more severe cases, coolant may spray into the combustion chamber, causing issues like backfiring and smoke during acceleration. This fault is caused by the aging of the water jacket gasket. Factors such as engine overheating or substandard coolant can accelerate the aging process of the gasket. 2. Fuel injector failure: After coasting downhill in gear and then attempting to accelerate, the engine cannot rev beyond approximately 1500 RPM. This is due to excessive fuel injector return flow, causing the metering unit to exceed its maximum fuel supply capacity. The ECU directly controls the engine speed, resulting in a speed limit. The issue can be temporarily resolved by turning the ignition key off and on again. The correct solution is to replace or repair the fuel injector.
13
2
Share

Where is the coolant filler port on the Ford Kuga?

Ford Kuga's coolant filler port is located on the left side of the engine compartment at the front of the vehicle, specifically on the auxiliary reservoir (expansion tank). Additionally, there is another filler port on the radiator. Coolant replacement procedure: Before performing a complete coolant replacement, conduct a thorough inspection to check for any signs of leakage or cracks in all hoses. Pay special attention to the five-way hose (named for its five connection points that distribute coolant to different parts of the vehicle). If any coolant leakage is detected in this area, replace the hose or reseal the connections as needed. Coolant replacement intervals: For vehicles with extended operation periods (e.g., taxis), high-quality coolant should typically be replaced annually. Vehicles with shorter operation cycles may replace coolant every two years or 30,000 kilometers. To prevent excessive foaming that reduces heat transfer efficiency, always verify the product's expiration date before adding. Long-life coolants remain effective for up to three years. If suspended particles, sediment, or discoloration are observed in the coolant, replace it immediately and flush the system.
11
0
Share

What Does 300 Horsepower Mean?

300 horsepower means the car can accelerate from 0 to 100 km/h in about 8 seconds. A vehicle with 300 horsepower is considered quite powerful, with the Volkswagen Golf GTI being one of the most common examples of such vehicles. Below are detailed explanations about horsepower: 1. Introduction: Horsepower is a commonly used unit of power in engineering. It generally refers to metric horsepower rather than imperial horsepower. By convention, 1 metric horsepower is defined as the work required to lift a 75-kilogram object 1 meter in 1 second. 2. Calculation: Countries like the United Kingdom and the United States use imperial horsepower. 1 imperial horsepower equals 550 foot-pounds per second, which is equivalent to 735.7 watts. In the late 18th century, British physicist James Watt (1736–1819) defined horsepower as the work required to lift a 1000-pound weight 33 feet in 1 minute to measure the power of newly manufactured steam engines. This is known as imperial horsepower, denoted by the letter HP.
4
0
Share

How to Unlock a Steering Lock?

When unlocking, slowly turn the handlebar to loosen the steering lock, and it will open. Below is relevant information about steering locks: 1. Features: The structure of the steering lock is designed to be difficult to pry open, thereby enhancing anti-theft effectiveness. The steering lock has a simple structure, low cost, easy operation, and is suitable for industrial production. 2. Structure: It consists of a lock body, lock core, spring, and pins. When locking the vehicle, the key is used to rotate the lock core out from the lock body. The lock core, fixed on the lock body, passes through the front fork steering tube and front connecting tube, preventing relative rotation between them. The lock core is characterized by being composed of a main lock core and a secondary lock core. The front part of the main lock core has a cylindrical structure, with the inner hole serving as the keyhole. Both the main and secondary lock cores contain a set of pin holes arranged in a cylindrical structure, with the axes of the pin holes parallel to the axis of the lock core.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.