How to Deal with ESP Malfunction Display in a Car?

1 Answers
Lilliana
07/29/25 11:38pm
Car displaying ESP malfunction can be handled by: reducing driving speed and avoiding excessive steering and turning. The function of ESP is to monitor the driving state of the car, helping the vehicle avoid deviating from its trajectory during emergency obstacle avoidance, understeer, or oversteer in turns. The types of sensors in the ESP system and their functions are divided into: 1. Steering sensor: monitors the steering wheel rotation angle; 2. Wheel speed sensor: monitors the speed of each wheel; 3. Yaw rate sensor: records the movement of the car around the vertical axis; 4. Lateral acceleration sensor: detects the centrifugal force generated when the car turns.
Was this review help?
13
4
Share
More Forum Discussions

What Are the Warning Signs of a Faulty Jetta Clutch Plate?

Here are the warning signs of a faulty Jetta clutch plate: 1. Feeling a decrease in the car's power, the car lacks strength. 2. The engine speed is high, but there is still insufficient power. 3. When starting, lifting the clutch feels uneven, the car has a jerking sensation, and there is a rough feeling when pressing, stepping, or lifting the clutch. Correct clutch usage methods: 1. When stepping on the clutch pedal, place the sole of your foot on the pedal with your heel touching the ground. When the clutch is pressed to the lowest point, keep the knee slightly bent. 2. Press the clutch to the lowest point. 3. Control the timing of the clutch. 4. Shift gears only after fully pressing the clutch pedal. 5. When pressing the clutch pedal, quickly release the accelerator pedal. 6. Ensure that clutch operation is coordinated with hand gear-shifting actions. 7. Avoid keeping your left foot on the clutch pedal while driving. 8. Under no circumstances should you use your right foot to press the clutch pedal while driving.
1
3
Share

How long does it take to get the driver's license after passing the subject 4 test in Weihai?

Some people can receive the license immediately after passing the test, while others may experience some delays, typically obtaining it within a week. In areas with lower efficiency, it might take a bit longer, usually around 15 days to get the license. Receiving the license after passing subject 4: After passing the subject 4 test, you are required to undergo at least 30 minutes of traffic safety and civilized driving education, including case studies of traffic accidents, and participate in a license oath ceremony. Only then will the vehicle management office issue the driver's license. Methods of receiving the license: There are several ways to receive the license: immediate issuance upon passing the test; mailing to the individual; picking it up at the driving school; or collecting it at the vehicle management office. Getting the license right after the test is the most convenient option. If immediate issuance is not available, choose the most convenient method for you.
19
5
Share

What are the consequences of not confirming the selected number on 12123?

If the car owner selects a license plate number in the 12123 system but does not confirm it, it will not affect the process of registering the plate at the vehicle management office. However, if the selection has already been confirmed, the owner must submit the required documents to the vehicle management office within the specified period to complete the registration. Failure to apply within the deadline will result in the automatic invalidation of the selected plate number, which will then be returned to the pool of available numbers. Consequences of not confirming a pre-selected number: If the owner fails to confirm the internet pre-selected license plate at the vehicle management office within the validity period, the user will be blacklisted and prohibited from pre-selecting a vehicle license plate online for 2 years, after which the blacklist status will be automatically lifted. Important notes for selecting a new license plate: It is highly recommended to first perform a simulated plate selection to familiarize yourself with all the steps and avoid selecting an unwanted plate due to operational or time constraints. There are restrictions on plate selection: you must confirm one out of 50 plate numbers. The selection is divided into 5 groups, with each group of 10 plates requiring a choice within 90 seconds. The selection area allows a maximum of 5 alternatives and must be confirmed within 180 seconds; otherwise, the selection will fail. Once a plate is successfully pre-selected online, if you wish to change it, do not wait until the 2-month registration validity period expires. If it expires, you will be blacklisted and unable to pre-select a plate online for 2 years. After successful online pre-selection, remember to register the plate promptly; otherwise, the plate will be reclaimed.
10
4
Share

Will I be fined if the rear left brake light is not working?

According to the "Road Traffic Safety Law" of China: Before driving a motor vehicle on the road, the driver should carefully check the safety technical performance of the vehicle; it is not allowed to drive a motor vehicle with incomplete safety facilities or components that do not meet technical standards, which may pose safety hazards. Check the brake light bulb: The most frequently used light on a car is the brake light, and the bulb has a relatively short lifespan. When the brake light is not working, the first thing to consider is the brake light bulb, and replacing the bulb can solve the problem. Check the brake light switch: If the brake light switch is faulty, all brake lights will not work. During inspection, you can use a wire to connect the brake light switch. If the brake lights turn on, it means the switch is damaged, and replacing the switch will fix the issue. Check the fuse: If both the bulb and the switch are confirmed to be working properly, the next step is to check the fuse. Some cars do not have a separate fuse for the brake light and share one with other electrical devices. In this case, you can check the operation of other electrical devices on the car. Identify any non-working electrical devices and replace the corresponding fuse.
13
2
Share

How to start the Trumpchi GA6 when the key fob battery is dead?

The method to start the Trumpchi GA6 when the key fob battery is dead is as follows: 1. Place the key near the steering wheel, as the car can still detect the key. 2. Press the start button to start the car. Note: Once the key fob battery is dead, it should be replaced immediately to avoid any inconvenience in normal vehicle usage. Related information is as follows: 1. The new generation Trumpchi GA6 features an N95-level protective filter technology, which achieves a filtration rate of over 95% for particles as small as 0.3 microns. It is also equipped with a negative ion generator and an air quality sensor to continuously monitor air quality, providing a clean and fresh air environment. 2. The front dual-zone smart air conditioning in the new generation Trumpchi GA6 allows for separate temperature adjustments and can automatically control the cabin temperature based on input signals from various sensors. The vehicle uses water-based PVC eco-friendly materials throughout, eliminating sources of odors, and implements a three-tier positive control system for materials, components, and the entire vehicle.
3
4
Share

How to eliminate noise in Tiguan?

Methods to eliminate noise in Tiguan are as follows: 1. To reduce engine noise, attach sound-absorbing materials under the hood. 2. To reduce wind noise, install sealing strips or perform door sound insulation. 3. To reduce tire noise, replace with comfort-oriented tires. Details are as follows: 1. Engine noise is generated and transmitted into the cabin through the front fenders, hood, firewall, and exhaust pipe as the engine speed varies. Therefore, vibration damping and sealing these areas can effectively control and reduce engine compartment noise. 2. Wind noise occurs during vehicle movement due to friction between rapidly flowing air and the car body. It enters the cabin through door gaps, so only by enhancing the vehicle's tightness and sound insulation can it be reduced. 3. Tire noise generally consists of three components: air noise from airflow in tire tread gaps and surrounding air disturbance, vibration noise from the tire body and tread patterns (particularly noticeable as road noise and uneven surface noise), and amplified resonance noise formed by friction/impact between tread and ground (especially on bumpy roads) combined with vibrations from components like fenders and mudguards.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.