How to Correct Steering When Turning Too Early or Too Late in Reverse Parking for Subject 2?

1 Answers
VonEverly
07/29/25 6:12pm
If you turn the steering wheel too early and the distance is slightly less than 30 centimeters, you can turn the wheel back half a turn. If you are about to hit the corner of the parking space, you need to straighten the steering wheel. Keep the steering wheel fully turned to the right while entering the parking space. When the car body is parallel to the side line, still do not straighten the steering wheel; straighten it only after increasing the distance.
Was this review help?
17
3
Share
More Forum Discussions

Can the Land Cruiser use 92-octane gasoline?

The Land Cruiser cannot use 92-octane gasoline. The minimum fuel grade required for the engine in this vehicle is 95-octane, and it can use 95-octane or higher gasoline. This model offers two powertrain variants, equipped with 4.0L and 4.6L naturally aspirated engines, respectively. Although these are naturally aspirated engines, both require 95-octane or higher gasoline. The Land Cruiser's body dimensions are 5170mm in length, 1980mm in width, and 1930mm in height, with a wheelbase of 2850mm. The vehicle features a front-engine, four-wheel-drive layout and is equipped with systems such as the Crawl Control (low-speed cruise driving assist system), Kinetic Dynamic Suspension System (KDSS), Hill-start Assist Control (HAC), and VVT-i system.
2
0
Share

Where is the location of the air conditioning relay in Kia K2?

The air conditioning relay in Kia K2 is located inside the engine compartment. The air conditioning relay is a current control component and an essential element of the air conditioning system. It serves as a monitoring and protection device for multi-functional three-phase three-wire power supply systems or three-phase electrical equipment. Through the form of relay output, it provides contact control signals for alarm output and protective circuit action output, serving the purpose of alarm and protection. The Kia K2 has a body length, width, and height of 4400mm, 1740mm, and 1460mm respectively, with a wheelbase of 2600mm. The engine equipped in this vehicle has a maximum power of 73.3kw and a maximum torque of 132.4nm.
4
3
Share

How to start a Mercedes-Benz C200L?

The starting method for the Mercedes-Benz C200L: First, press the brake pedal located below the steering wheel, then press the one-touch start button to ignite the engine. Next, pull the electronic handbrake on the right side of the steering wheel to release the vehicle's braking state. After that, move the gear lever on the right side of the steering wheel to shift the gear to D, allowing the vehicle to drive normally. The Mercedes-Benz C200L has a body length, width, and height of 4784mm, 1810mm, and 1457mm respectively, with a wheelbase of 2920mm. The car features a front-engine, rear-wheel-drive layout, and its engine delivers a maximum power of 115kW and a maximum torque of 250Nm.
3
4
Share

What are the effects of turning the steering wheel while stationary on the car?

Here are the specific effects of turning the steering wheel while stationary on the car: 1. First, it will cause the steering wheel to age prematurely. Turning the steering wheel while stationary for a long time can also cause significant damage to the steering wheel itself. 2. It affects the service life of the car tires. When the vehicle turns the steering wheel while stationary, the entire weight of the car is concentrated on the front tires, causing uneven pressure on the tires and increasing their wear. 3. It increases hydraulic pressure, weakening the load capacity of the vehicle tires. When turning the steering wheel while stationary, the vehicle relies on vacuum assistance, which reduces the driving difficulty for many car owners, but during this process, the pressure on the power steering pump increases significantly.
13
3
Share

What to Do If the First Maintenance Manual Is Lost?

Solution for losing the first maintenance manual: Verify with the staff at the 4S dealership to confirm that the car was purchased there. In this case, the first maintenance can be performed without the manual. For subsequent maintenance visits, the 4S shop's computer system will have the maintenance records, making the manual completely optional. Additional Information: 1. The first car maintenance typically includes changing the engine oil and oil filter to remove impurities from the engine. It also involves cleaning the air filter and cabin air filter, conducting a full vehicle inspection, and for some domestic cars, replacing the gear oil. The first maintenance is usually free of charge. 2. General maintenance recommendations include two criteria: time interval (every six months) and mileage interval (every 5,000 kilometers). Whichever comes first should be followed.
1
0
Share

How to Check Engine Compression Pressure?

Engine compression pressure testing method is as follows: 1. First, ensure the battery is fully charged; warm up the engine to normal operating temperature; 2. Turn off the engine and let it cool for 10 minutes; follow the "Fuel System Safety Inspection Steps" to remove the fuel pump relay. 3. Disconnect the ignition coil connector and remove the spark plugs; 4. Connect a pressure gauge to the spark plug hole of cylinder No. 1, then fully depress the accelerator pedal and start the engine; 5. Start the engine and record the maximum reading on the pressure gauge to obtain the pressure; Additional Information: 1. If the compression pressure increases, it may indicate wear on the piston, piston rings, or cylinder walls, requiring an overhaul; if adjacent cylinders show low pressure, it suggests the cylinder gasket may be damaged or the cylinder head may be deformed, necessitating an overhaul; if the compression pressure remains low, it may indicate stuck valves or poor sealing surface contact, requiring an overhaul. 2. Before measuring engine compression pressure, remove all spark plugs and place the reset-to-zero gauge at the spark plug hole of the cylinder being tested (some compression gauges screw into the spark plug hole). Start the engine and observe and note the value indicated by the gauge's first jump. Release the starter to return the gauge to zero. Repeat the measurement following the same procedure, but each measurement should take the highest value the gauge's first jump can reach as the standard. The value the gauge first jumps to is the true pressure of that cylinder.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.