How to Control Excessive Speed When Climbing in Subject 2?

1 Answers
CalebDella
07/25/25 5:42am
The method to control excessive speed when climbing in Subject 2 is: Master the correct posture of the clutch, keep your heel as close to the ground as possible, and bend your knees when the clutch is fully depressed. If the vehicle speed gets out of control, stay calm, first fully depress the clutch, then fully depress the brake. Avoid wearing hard-soled shoes as they hinder the perception of the clutch's position. Always operate the clutch with the correct posture and standards to prevent slipping. The reasons for insufficient power when climbing in Subject 2 are: 1. Lifting the clutch too quickly, causing the power to lag and the vehicle to roll back; 2. Releasing the handbrake without applying the throttle, resulting in no climbing power.
Was this review help?
13
5
Share
More Forum Discussions

How long is the Audi A3 sedan?

The Audi A3 sedan has a length of 4351mm, a width of 1815mm, and a height of 1458mm, with a wheelbase of 2630mm. It is a compact 5-door, 5-seat hatchback with front-wheel drive. The front suspension uses MacPherson strut independent suspension, while the rear suspension employs a multi-link independent suspension. The Audi A3 is equipped with a 1.4T turbocharged engine and a 7-speed dual-clutch transmission, delivering a maximum power of 110 kW at 5000 to 6000 rpm and a maximum torque of 250 Nm at 1750 to 3000 rpm.
11
5
Share

What Causes Abnormal Noise When Accelerating a Car?

Reasons for abnormal noise when accelerating a car: 1. Fuel pump motor noise: When internal wear or impurities exist in the fuel pump motor, abnormal noise occurs upon acceleration. This issue requires fuel pump replacement. 2. Throttle body noise: Modern throttle bodies use electronic control, with motors naturally controlling valve opening/closing. Gear wear in the motor causes insufficient engagement and noise. Excessive carbon deposits or sludge in the throttle body can also cause noise. Cleaning the throttle body may help, but motor damage requires throttle body disassembly and servo motor replacement. 3. Poor lubrication in accelerator pedal bearings: Apply grease to the bearings for lubrication. 4. Clutch release bearing damage causing incomplete clutch disc separation: Remove the clutch and replace the release bearing.
10
4
Share

What is the working condition table for XCMG 80l6?

The working condition table for XCMG 80l6 is the lifting performance table for the XCMG 80-ton crane's main boom, including boom length (with outriggers fully extended) and working radius (m) such as 12.0m, 2.5, 3.0, 3.5, etc. Classification of license plate colors: There are four background colors for vehicle license plates, namely blue, yellow, white, and black. National license plate standards: The size of license plates for large vehicles is front: 440*140 (same as small vehicles); rear: 440x220. According to the 'Motor Vehicle Registration Regulations', medium-sized buses, large buses, and urban buses have yellow license plates; medium-sized trucks, large and medium-sized trucks, and trailers also have yellow license plates. The type of vehicle is determined based on the vehicle's factory certification.
5
4
Share

How to Make a Proper U-turn with a Car?

To make a proper U-turn with a car, follow these steps: 1. Shift into P or N gear and activate the low-range four-wheel drive mode; 2. Change to D gear, engage the crawl mode, and release the brake; 3. Once the car is in automatic driving mode, turn the steering wheel to a certain angle and use the speed button to control the speed. Things to pay attention to when making a U-turn: 1. Check if the intersection allows U-turns; 2. Ensure there are no oncoming vehicles; 3. On wider roads, try to make a large loop for a single smooth U-turn. Intersections where U-turns are permitted include: 1. Intersections with U-turn signs; 2. Intersections without explicit no U-turn or no left-turn signs; 3. Areas with yellow grid lines.
20
2
Share

Where is the reversing radar switch on the 2021 Levin?

2021 Levin reversing radar switch is located on the lower left side of the driver's compartment, next to the headlight height adjustment with a letter "P" marked on it. Function of reversing radar: Accurately measures the distance between the rear of the car and the nearest obstacle; When reversing to the limit distance, it can emit a rapid warning sound to remind the driver to pay attention to braking; It can repeatedly emit voice warnings to remind pedestrians to pay attention. Working principle of reversing radar: When reversing, the Levin reversing radar uses the principle of ultrasound. The probe installed on the rear bumper sends ultrasonic waves to hit the obstacle and reflects the sound waves, calculates the actual distance between the car body and the obstacle, and prompts the driver to make parking or reversing easier and safer.
19
0
Share

What are the reasons for the air conditioning not cooling in a Hyundai Elantra?

The reasons for the air conditioning not cooling in a Hyundai Elantra are: 1. The compressor lacks refrigerant; 2. The compressor lacks oil; 3. Internal damage to the air conditioning pump; 4. Excessive refrigerant charge in the air conditioning system; 5. Blockage in the refrigerant pipeline; 6. Fault in the refrigeration system circuit; 7. Damage to the thermostat interface. The Hyundai Elantra is a compact 4-door 5-seater sedan with body dimensions of: length 4570mm, width 1775mm, height 1445mm, and a wheelbase of 2700mm. It is equipped with a 1.6L naturally aspirated engine and a 6-speed manual transmission, delivering a maximum power of 93.8 kW and a maximum torque of 156 Nm.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.