How to Connect a Buick Dash Cam to a Phone?

Brief Description of the Causes of Drive Axle Oil Leakage

Drive axle oil leakage is caused by loosening or damage. Below are some of the fault causes: 1. Loosening: Drive axle loosening may be due to loose oil filler or drain plugs; worn or hardened oil seals, oil seals installed in reverse, misalignment between the oil seal and shaft neck, or grooves worn into the shaft neck. Additionally, the drive axle must withstand vertical forces, longitudinal and lateral forces acting between the road surface and the frame or body, as well as braking torque and reaction forces. 2. Damage: Drive axle damage may be caused by damaged fastening screws; blocked ventilation holes; casting defects or cracks in the axle housing; excessive gear oil leading to increased internal pressure during operation, causing gear oil to seep out, etc.

9

5

Share

Where is the USB port in the Honda Avancier?

The USB port in the Honda Avancier is located on the side or rear of the center control panel. Below is some relevant information about the Avancier: 1. Exterior: The Avancier is a new mid-size luxury SUV launched by GAC Honda. With its design concept that transcends the times, the Avancier's exterior showcases a majestic and powerful style, combining strength and beauty. Features like the wide front grille, eagle-wing LED headlights, and bold body lines highlight its uncompromising sharpness. 2. Interior: The interior is equipped with a symmetrical design dashboard wrapped in soft materials and wood grain decorations. A large adjustable floating LCD screen in the center enhances the technological atmosphere inside the car. The engine comes with practical features such as one-key start, electronic parking brake, seat heating, reverse radar, and vehicle stability system. It also includes comfort and tech configurations like rear automatic air conditioning, central armrest entertainment system control panel, and rear sunshades.

10

4

Share

Correct Method for Connecting Jumper Cables to a Car Battery

Correct Method for Connecting Jumper Cables to a Car Battery The correct method for connecting jumper cables to a car battery is to securely attach them to the positive terminal of the battery. Below is a partial introduction to connecting jumper cables to a car battery: 1. Jumper Cables: Attach one end of the red cable to the positive terminal of the battery, connect the jumper cable, attach the other end of the red jumper cable to the positive terminal of the charged car's battery, attach one end of the black cable to the negative terminal, and attach the other end of the black cable to the negative terminal of the charged car's battery or to the car body or a metal part of the engine mount. 2. Precautions: Ensure that the contact points are securely clamped, as the current is high during startup. Remove the protective cover from the positive terminal of the car battery, attach one end of the red cable (+) to the positive terminal of the battery, and proceed to connect the jumper cables.

9

2

Share

Which way should the steering wheel turn when reversing to the left?

When reversing to the left, the steering wheel should be turned to the right. Below is a partial introduction about steering during left-side reversing: 1. Technique: Engage reverse gear, slowly release the clutch pedal to start reversing in a semi-engaged state, look at the right rear window, when the 3ccc mark on the right rear window glass aligns with the right boundary line of the garage, immediately and evenly turn the steering wheel fully to the right. Check the left rearview mirror, observe both side mirrors to adjust the vehicle's position, and reverse into the garage. 2. Precautions: When exiting the garage, engage first gear, slowly release the clutch pedal to start moving forward in a semi-engaged state.

14

2

Share

How to Extract Oil from Inside a Car?

To extract oil from inside a car, you should first fill up the fuel tank and then proceed with the extraction. Here are some steps for extracting oil: 1. Extracting oil on a flat surface: Extracting oil on a flat surface is not very easy. If you want to extract oil from a car, first fill up the fuel tank, then drive the car onto a slope. The steeper the slope, the easier it will be to extract the oil. 2. After parking: Secure the car with the front facing upwards, shift the gear into first, and engage the handbrake. Once the car is secured, you can open the fuel tank cap and insert the pre-prepared hose into the tank, trying to reach as close to the bottom as possible.

2

Share

What engines are generally used in Changan Oushang?

Changan Oushang generally uses Dong'an engines, which are independently developed and produced by Changan Company, with the factory located in Chongqing. Different Changan Oushang models have different engines. The engine model for Oushang X5 is JL473ZQ2, with a maximum horsepower of 180, maximum power of 132kw, maximum power speed of 5500rpm, and maximum torque of 300N.m. The engine model for Oushang X7 is JL476ZQCF, with a maximum horsepower of 178, maximum power of 131kw, maximum power speed of 5500rpm, and maximum torque of 265N.m. For daily maintenance of Changan Oushang engines, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB_CD grade diesel engine oil should be selected based on mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid faults, oil should be changed regularly based on usage conditions, and the oil quantity should be moderate. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to pass through the bypass valve and bringing dirt back to the lubrication area, accelerating engine wear and internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acid, moisture, sulfur, and nitrogen oxides in the combustion chamber enter the crankcase through the gap between the piston ring and cylinder wall, mixing with metal powder from part wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, blocking the filter and oil holes, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine works properly but also extends the overall lifespan of the radiator and engine.

5

Share

How to Connect a Buick Dash Cam to a Phone?

Brief Description of the Causes of Drive Axle Oil Leakage

Where is the USB port in the Honda Avancier?

Correct Method for Connecting Jumper Cables to a Car Battery

Which way should the steering wheel turn when reversing to the left?

How to Extract Oil from Inside a Car?

What engines are generally used in Changan Oushang?

How to Use Rearview Mirrors?

What to Do When There Is Green Powder on the Negative Terminal of a Car Battery?

Should Cars Be Waxed?

How Long Does a Turbocharger Generally Last?