How to Clear the Tire Pressure Warning on Wuling Hongguang?

2 Answers
DiAngelo
07/29/25 2:21am
Steps to clear the tire pressure warning on Wuling Hongguang: Turn off the vehicle, then turn on the power for a self-check. Inflate all four tires to the standard pressure. Press and hold the tire pressure monitoring button located on the right side in front of the gear lever for three seconds until a beep is heard, then release. The tire pressure warning light on the dashboard will turn off. What to do if the tire pressure is low: If no damage is visible on the car's tires, simply inflate them to the normal pressure and reset the tire pressure system. If a puncture is found upon inspection, drive to a car repair shop for a tire repair, then reinflate the tire. If the low tire pressure warning appears again after inflation without any punctures, it might be due to air leakage caused by a deformed wheel rim. It is recommended to check the wheel rim and replace it if necessary. How tire pressure monitoring works: The system uses pressure sensors installed inside the tires to measure the tire pressure. A wireless transmitter sends the pressure information from inside the tire to a central receiver module.
Was this review help?
2
2
Share
SanSimon
08/12/25 6:19am
I remember the first time the tire pressure warning light came on in my Wuling Hongguang, I was quite nervous. It happened in the morning when I was driving to work, so I immediately pulled over to check the tires. I noticed the right front tire pressure was a bit low, so I went to a nearby gas station to top it up. After driving a short distance, the warning light went off by itself. If the tire pressure is normal but the warning light remains on, it might be due to dust stuck in the sensor or a system malfunction. In that case, I would start the engine, look for a menu button on the left side of the steering wheel or on the dashboard, navigate to the tire pressure settings, and select reset. It's good practice to check the tire pressure regularly, at least once a month, and maintain it around 230 kPa to avoid false alarms. After all, tire issues are directly related to driving safety, so never take them lightly.
Was this review help?
6
0
Share
Expand All
More Forum Discussions

What causes abnormal noise during startup?

The causes of abnormal noise during startup are as follows: Belt slipping on the generator: The reason for abnormal noise during startup is that the belt is slipping on the generator, causing intense friction and vibration between the belt and pulley, which produces a certain frequency of noise. Loose or aged belt: The reason for belt aging is that the belt gradually hardens and loses elasticity during prolonged use, reducing the friction between the belt and pulley. In this case, the only solution is to replace the belt. Factors that can lead to a loose belt include improper adjustment of the belt tensioner or insufficient tensioner spring force. In such cases, the tension of the belt tensioner should first be adjusted. If this doesn't work, the tensioner should be replaced.
2
1
Share

Where are the audio speakers located in the Haval H7?

Haval H7 audio speakers are generally located near the triangular window on the A-pillar or on the C-pillar. Working Principle: Automotive electric horns produce sound through the vibration of a metal diaphragm. The car electric horn consists of an iron core, a magnetic coil, contacts, an armature, a diaphragm, etc. When the driver presses the horn switch, current flows through the contacts to the coil, generating magnetic force that pulls the armature, forcing the diaphragm to move. The movement of the armature disconnects the contacts, interrupting the current and causing the coil's magnetic force to disappear. Speaker Introduction: Commonly known as a speaker, it is an indispensable component in an audio system. The number of speakers determines the distribution of sound emission points.
4
0
Share

What causes the 'Engine Malfunction Service Required' warning in a Focus?

If the 'Engine Malfunction Service Required' warning appears in a Focus, it could be due to poor fuel quality, engine failure, carbon buildup in the engine, or issues with the oxygen sensor. The details are as follows: Fuel Quality: If a Focus frequently uses low-quality fuel, it can easily lead to incomplete combustion, causing the gasoline filter screen to clog. Prolonged use of such fuel can also damage the spark plugs, catalytic converter, and oxygen sensor. Carbon Buildup: If the Focus often drives at low speeds in urban areas, it can easily lead to carbon buildup in the throttle or inside the engine. When the vehicle has been driven for a long time, the insulation layer of the high-pressure wires may age and become prone to breakdown, which can also trigger the 'Engine Malfunction Service Required' warning.
18
1
Share

Does the Volkswagen Tiguan I have a remote start system?

Volkswagen Tiguan I has a remote start system. Remote Start: Refers to the vehicle's engine being able to be started remotely, allowing for pre-heating/cooling of the passenger compartment before departure. ERS is enabled via the key and/or Volvooncall (Volvo On Call). Steps to stop remote start operation: Press the remote key buttons (1), (2), or (4) to unlock the car, open a door, press the accelerator or brake pedal, move the gear selector from P position, or if the remote start activation time exceeds 15 minutes. When the remotely started engine shuts off, the turn signals will flash for 3 seconds.
2
0
Share

How Much Stake Did Geely Acquire in Volvo?

Geely Holding Group acquired 100% of the shares of Volvo Car Corporation and related assets including intellectual property rights, with the transaction completed in the third quarter of 2010. Relevant information is as follows: Introduction: Today, Volvo is divided into two entities—Volvo Car Corporation and Volvo Group. Volvo Cars was once part of Volvo Group's passenger car business, but Volvo Car Corporation is now owned by Geely Holding, while Volvo Group operates independently. Agreement: In 1999, Ford Motor Company acquired Volvo Cars. On December 24, 2009, Ford Motor Company and Zhejiang Geely Holding Group—the parent company of Chinese automaker Geely Auto—reached a preliminary agreement on the sale of Volvo Cars.
10
0
Share

How to reset the brake warning light on a BMW X1?

BMW X1 brake warning light reset method: 1. Close the door and turn on the ignition; 2. Press and hold the black button at the bottom left of the instrument panel until the oil or brake pad indicator appears; 3. When a triangle symbol appears in the middle, do not release the button; 4. When the brake pad indicator appears, release the button and press and hold it again, "RESET" or reset will be displayed; 5. Release and press and hold again to complete the reset. The BMW X1 is a compact urban SUV model, with body dimensions of 4454mm in length, 1798mm in width, 1545mm in height, and a wheelbase of 2760mm.
6
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.