How to Cleanly Remove Vehicle Inspection Stickers?

What materials are needed for the first maintenance of Changan CS55?

Items required for the first maintenance include: driver's license; maintenance manual; warranty manual; owner's ID card; vehicle's driving license; vehicle registration book; vehicle purchase invoice. Bring these to the designated first maintenance facility for the vehicle's initial service. Important note: Schedule an appointment with the 4S store in advance. The first maintenance refers to the initial service after a new car has been driven. The specific timing varies by vehicle, typically after driving 5,000 kilometers or 6 months. It's crucial to attend the first maintenance on time, neither early nor late. The completion of the first maintenance signifies the end of the vehicle's break-in period, allowing it to be driven under standard load and normal speed as required by the car. The timing for the first maintenance is calculated from the date of vehicle pickup. There are two indicator values for the first maintenance: mileage and time. Whichever indicator is met first will be the standard. First maintenance tasks include: changing the engine oil and oil filter, cleaning the air filter, checking various fluid levels for normalcy, inspecting the generator belt and wiper blades for damage, checking tire pressure for normalcy, and inspecting tires for damage or bulges. Time required: Completing all tasks takes approximately 2 hours. The most important aspect of a new car's first maintenance is changing the engine oil and oil filter. When changing the oil, the oil filter must also be replaced. The choice of oil must refer to the "Vehicle Usage and Maintenance Manual," as different vehicle models specify different oil grades. Maintenance precautions: Do not wash the interior of the car with water: Many people clean their cars during holidays, washing the exterior with water and wiping it with a cloth. It's important to note that the interior should not be washed directly with water. If the floor mats are dirty, use a vacuum cleaner or take them out to brush with detergent, dry them, and then put them back. There are many holes under the rubber mats on the driver's side floor. If water enters, it won't dry but will flow through these holes to areas like the gearbox, causing erosion and corrosion. The best practice is to vacuum clean first and then wipe with a cloth to prevent water accumulation. Do not mix different brands of antifreeze: When the car's antifreeze is low, it's recommended to drain the existing antifreeze and add the same brand from the start. Different brands of antifreeze have varying chemical properties and use different corrosion inhibitors. Mixing them can lead to unnecessary problems. Do not lubricate tire bolts and nuts: When bolts on a moving car rust, they are often oiled to function properly again. Some people apply lubricant to bolts and nuts to prevent rust, but this introduces unnecessary risks to safe driving. At high speeds, bolts and nuts can easily loosen or even fall off, leading to driving malfunctions.

9

3

Share

Where is the WM W6 car produced?

WM Motors established its R&D team in Germany and set up a production plant in Wenzhou, China for manufacturing. Here is some relevant information about WM Motors: Professional Team: WM Motors has assembled a 150-person professional team in Wenzhou, responsible for factory construction and the implementation of Industry 4.0 flexible manufacturing. Latest Model: WM has launched the WM EX5-SUV model, an internet-connected pure electric vehicle that allows customization based on personal preferences. The EX5 with the maximum battery capacity can achieve a range of over 460KM.

1

4

Share

What powers the windshield wipers?

The power source of the windshield wipers comes from an electric motor, which serves as the core of the entire wiper system. The quality requirements for the wiper motor are very high, as it utilizes a DC permanent magnet motor. The wiper motor installed on the front windshield is integrated with the worm gear mechanical assembly. The function of the worm gear mechanism is to reduce speed and increase torque. Its output shaft drives a four-bar linkage mechanism, which converts continuous rotational motion into a side-to-side oscillating motion. Automotive windshield wipers, also known as wipers, are devices used to sweep away raindrops and dust adhering to the vehicle's windshield, thereby improving the driver's visibility and enhancing driving safety.

16

1

Share

What is the engine RPM when the car speed is 70 km/h?

When the vehicle speed is 70 mph, which is approximately 113 km/h, the engine RPM is around 2600. Here are some relevant information: 1. The engine RPM is influenced by two main factors: the engine displacement and the transmission. At the same speed, a larger engine displacement results in lower RPM. 2. Both excessively high and low RPM are generally not good. If the RPM is too low, the gasoline may not burn completely, leading to rapid accumulation of carbon deposits in the vehicle. If the RPM is too high, it can accelerate the natural wear of the engine cylinders, shortening the engine's lifespan.

20

2

Share

What Causes One Headlight to Be On While the Other Is Off?

The reasons for one headlight being on while the other is off are as follows: 1. Car headlights are divided into high beam and low beam. The switches for the two bulbs of either the high beam or low beam are connected together. If they are on, both will be on; if not, both will be off. If only one side is on, it means the bulb on the other side is either burnt out or has poor contact. Testing this is simple—just swap the bulbs on both sides to identify the issue. 2. If the bulb is damaged, it needs to be replaced. When selecting a bulb, be sure to choose the correct model. Car headlight sockets are produced according to uniform standards, so as long as the headlight model matches, it can be installed.

8

1

Share

How to Read the Fuel Gauge?

Method for reading the fuel gauge: The fuel gauge has several markings, which are full, half, and quarter. Car owners can check the remaining fuel level in the tank from these markings. Most car dashboards are equipped with an onboard computer display that can show the remaining driving range. When refueling the car, it is advisable to choose reputable large gas stations with high-quality fuel and select the correct gasoline grade. If poor-quality gasoline is frequently used, carbon deposits in the engine will increase, which is harmful to the engine. If carbon deposits accumulate in the combustion chamber, it will raise the compression ratio, leading to engine knocking. Therefore, it is recommended that car owners regularly clean the carbon deposits from their vehicles.

19

4

Share

How to Cleanly Remove Vehicle Inspection Stickers?

What materials are needed for the first maintenance of Changan CS55?

Where is the WM W6 car produced?

What powers the windshield wipers?

What is the engine RPM when the car speed is 70 km/h?

What Causes One Headlight to Be On While the Other Is Off?

How to Read the Fuel Gauge?

Should the Audi A6 use 95 or 98 octane gasoline?

What are the three driving mode functions of the Wildlander?

What are the common faults of wipers?

How Does an Oxygen Sensor Work?