How to Check Tire Pressure on Buick Excelle?

1 Answers
Rachel
07/30/25 2:28am
Method to check tire pressure on Buick Excelle (not available for base models): 1. Press the "MENU" button on the turn signal lever to switch the small screen on the instrument panel to the "Vehicle Information Menu." 2. The Vehicle Information Menu has only two pages: overspeed alarm and tire pressure monitoring. 3. If the overspeed alarm is displayed, rotate the knob at the top of the left lever to switch to the tire pressure monitoring information, where you can view the tire pressure of all four wheels. Buick Excelle tire pressure monitoring reset method: 1. First, park the vehicle, engage the handbrake, and operate with the vehicle powered on. 2. Press the MENU button on the turn signal lever to switch the small screen on the instrument panel to the Vehicle Information section. 3. Rotate the up and down selection buttons on the turn signal lever to find the tire pressure information section. 4. Press and hold (long press) the SET/CLR function button at the head of the turn signal lever until the display shows whether to perform tire pressure learning, then select "Yes." 5. After selection, the horn will sound twice to confirm the start of tire pressure learning. 6. At this point, the left front turn signal will light up, and then proceed to deflate the tire. The order is: left front, right front, right rear, left rear. Unscrew the valve cap to release air from the tire. When the horn sounds once and the current tire's turn signal turns off while the right turn signal lights up, you can release the valve. 7. With the right turn signal lit, repeat the above method to continue deflating the right front tire until the horn sounds once and the right turn signal turns off, then stop deflating. 8. Proceed in order, observing the tire pressure status of each tire on the instrument panel. The tire pressure will be lower than normal, so you need to inflate the tires in sequence to bring the pressure back to the normal range, generally between 2.3~2.5. This completes the tire pressure reset.
Was this review help?
6
2
Share
More Forum Discussions

What are the consequences of running a red light?

For motor vehicles that run a red light, according to the provisions of the Road Traffic Safety Law of the People's Republic of China, they will be subject to a fine and have six points deducted from their driver's license. Therefore, it is essential to pay attention to traffic signals when passing through intersections. Here is some relevant information: 1. Precautions: When approaching a traffic light intersection, slow down, yield to pedestrians, and enter the appropriate lane in advance; stop promptly when the yellow light comes on to avoid running a red light. 2. Handling methods: Running a red light can be addressed through the mobile app "Traffic Management 12123" or by visiting the vehicle management office or the traffic management department of the public security authorities.
4
1
Share

What to Do If 6 Points Are Deducted from a Class A Driver's License?

Deducting 6 points can be divided into two situations: one is during the probationary period, and the other is after becoming a regular driver. For a Class A driver's license, if 6 points are deducted during the probationary period, the probationary period will be extended by one year. If another 6 points are deducted during the extension period, the driver's license will be revoked. For regular drivers, whether it's a Class A, B, or C driver's license, as long as the points deducted do not reach 12, there is no impact. However, one should drive more carefully in the future.
20
0
Share

Why does the Corolla idle shake?

Vehicle idle shaking refers to noticeable body vibration when starting the vehicle or keeping the engine running while stationary. The causes and specific solutions for Corolla idle shaking are as follows: 1. Cause one: The throttle body is dirty or the fuel injectors have excessive carbon deposits, causing gasoline to be largely absorbed by the carbon deposits and resulting in an overly lean air-fuel mixture during cold starts. Solution one: Clean the fuel system and check the idle air control valve for carbon deposits, cleaning it promptly if present. 2. Cause two: Ignition system issues. Solution two: Inspect the working condition of spark plugs, high-voltage wires, and ignition coils, replacing spark plugs in a timely manner if necessary.
16
2
Share

How to Turn on the Cold Air Conditioning in a Civic?

The first step to turn on the cold air conditioning in a Civic is to press the AC button and rotate it to the left into the blue zone to activate the cold air. It is essential to turn on the AC button when activating the cold air, as the AC button controls the air conditioning compressor, which determines whether the compressor operates. Only when the compressor is working will cold air be blown out. The compressor not only cools the air but also dehumidifies it. The Civic has dimensions of 4649mm in length, 1800mm in width, and 1416mm in height, with a wheelbase of 2700mm. The front suspension system is a MacPherson strut independent suspension, and the rear suspension system is a multi-link independent suspension, with front-wheel drive.
3
3
Share

How to Replace the Brake Light on a Lavida?

Lavida's brake lights use halogen light sources, which have limited ignition cycles and lifespan, so the brake lights should be replaced promptly. The specific steps to replace the brake light on a Lavida are as follows: 1. The rear tail light assembly is located in the trunk; first, open the trunk. 2. There is a protective pad behind the rear tail light that serves as a protective cover; then, remove the protective pad of the rear tail light. Be careful not to use excessive force when removing the protective pad. 3. After removing the protective pad, you can see the circuit assembly. Use a screwdriver to unscrew the screws on the light and locate the circuit board. 4. Remove the old bulb. 5. Install the new bulb, and the brake light replacement is complete.
8
5
Share

How Often Should Valve Stem Seals Be Replaced?

Valve stem seals generally need to be replaced every 20,000 to 30,000 kilometers. Valve stem seals are a type of oil seal, typically composed of an outer frame and fluororubber vulcanized together. The seal's inner diameter is equipped with a self-tightening spring or steel wire, designed to seal the engine valve guide. Valve stem seals prevent engine oil from entering the intake and exhaust pipes, thereby avoiding oil loss, preventing the leakage of the air-fuel mixture and exhaust gases, and stopping engine oil from entering the combustion chamber. As a critical component of the engine's valve train, valve stem seals are usually made of fluororubber. Over time and under the influence of alternating working temperatures, rubber components lose their plasticizers. Damaged valve stem seals can cause the engine to burn oil, resulting in blue smoke during cold starts, along with symptoms like poor acceleration and engine vibration.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.