How to Check the Wear Level of Car Tires?

How to lock the child lock on Audi Q5L?

First, press the button on the rear door handle to open the door. The Q5 features an intelligent door lock system. With the car key, you can directly open the door and then pull open the rear door. The child lock switch can be found on the passenger side. The child lock switch is located on the door pillar. Rotating this switch will activate the child lock, preventing children from opening the door from the inside during the ride. The child safety lock prevents the rear doors from being opened from the inside and disables the operation of the rear window lifters, ensuring greater safety for children.

10

2

Share

How is the date displayed on a tire?

Tire production dates are located on the outer edge of the tire. The 11-digit number and letters immediately following the "DOT" marking on the tire sidewall represent the tire's identification number or serial number. The last four digits of the serial number indicate the tire's production date. The production date is used to identify the age and storage time of the tire. The tire production date code format: the first two digits represent the production week, and the last two digits represent the production year. For example, 1204 means the tire was produced in the 12th week of 2004. Five situations that require tire replacement: 1. The production date is approaching; 2. Severe tread wear; 3. Whether the tire has bubbles; 4. Abnormal tire pressure; 5. Whether the tire has cuts.

8

2

Share

How to set up the CRV reversing radar to not beep?

The first step to set up the reversing radar to not beep is to step on the CRV's brake pedal. The second step to set up the reversing radar to not beep is to press the CRV's one-button start key. Then turn on the CRV's dashboard to light it up and power up the entire vehicle. Next, press the reversing radar's on/off button located inside the CRV to activate the car's reversing radar. At this point, the CRV will be assisted by the reversing radar at the rear of the vehicle for reversing.

5

2

Share

How to Heat and Modify Car Seats?

Turn off the car's power and check if the car key is in the off position. Use tools to remove the car seat where the heating system will be installed. Remember the disassembly sequence, determine the placement of the car seat heating pad, and place the side of the heating pad with the grid adhesive facing down, attaching it to the foam cushion. Slowly peel off the grid adhesive from one end while sticking it down. For areas with tension straps on the foam cushion, insert the heating pad into the bottom of the tension strap groove, keeping it flush with the bottom of the groove. Attach the wear-resistant tape inside the tension strap groove. Ensure the heating pad remains smooth without any wrinkles. Route the car seat heating pad wiring harness from the rear of the foam cushion and connect it to the main wiring harness. Test the constant power wire, ignition wire, and night driving wire with a test pen or multimeter two or more times to confirm accuracy before connecting. Secure the ground wire to the grounding screw.

5

1

Share

How to Clean a Dirty Panoramic Sunroof Fabric?

When closed, the exterior can be cleaned normally as you would wash a car, while the interior can be wiped with a soft, damp cloth. After opening the sunroof, dust in the surrounding grooves can be cleaned by wrapping a dry cloth around a thin wooden stick to wipe, then using a vacuum to remove the dust, followed by wiping with a damp cloth. Generally, after 2~3 months of use, the rubber seals or tracks should be cleaned with sandpaper soaked in cold water, and a small amount of lubricant can be applied after wiping. Regularly or before long-term storage, finer calcium powder can also be used for frequent cleaning to extend the lifespan of the sealing rings. Simply wipe away any residual moisture along the edges.

3

5

Share

What is the procedure for transferring ownership of a used car?

Go to the vehicle management office to collect the vehicle transfer application form and agreement. Fill out the transfer application form and agreement. For company-owned vehicles, the company seal is required. Both the buyer and seller need to provide proof, and the new owner must submit a copy of their business license. For passenger cars, a copy of the quota certificate is also required. Clear any outstanding traffic violation records of the vehicle to ensure the vehicle is within its annual inspection validity period. Submit the completed transfer application form, agreement, relevant copies, and the original vehicle license to the used car trading point to obtain an appraisal form. Then, use the relevant transfer documents to complete the transfer procedure at the traffic police department.

17

0

Share

How to Check the Wear Level of Car Tires?

How to lock the child lock on Audi Q5L?

How is the date displayed on a tire?

How to set up the CRV reversing radar to not beep?

How to Heat and Modify Car Seats?

How to Clean a Dirty Panoramic Sunroof Fabric?

What is the procedure for transferring ownership of a used car?

What is the meaning of the Lexus logo?

How to Remove the Spark Plugs on a Volkswagen Sagitar?

How to Check the Tire Production Date?

Is it a violation to make a U-turn over a solid white line?