···
Log in / Register

How to Check the Production Date of Volkswagen Car Glass?

3 Answers
SkylarFitz
08/26/25 5:22am
Car glass production date is located on the trademark in the corner of the car glass, consisting of several dots and a number. More information about car glass production date is as follows: 1. The number represents the production year of the car glass. If the dots are on the left, it indicates production in the first half of the year, while dots on the right represent production in the second half. By analyzing the numbers and black dots on the trademark, you can determine the production date of the car glass. 2. The date code on the glass consists of only one number, representing the last digit of the year. For example, the number 8 represents 2008. 3. The production date of the glass and the vehicle will not differ by more than ten years. The month of glass production can be analyzed and determined by the black dots before or after the number.
Was this review help?
11
5
Share
CeciliaLee
09/08/25 7:28am
I've been working on Volkswagen cars for a long time, and the glass production date is actually quite easy to spot in the corner of the glass. For example, in the lower right or lower left corner of the windshield, there's a small imprint with numbers and dots. The number represents the last digit of the year—for instance, '7' means 2017. The dots indicate the month: if the dots are on the left side of the decimal point, one dot stands for January, two dots for February, and so on up to December. Sometimes the dots are on the right side, where fewer dots mean earlier months and more dots mean later months. I remember once seeing '19..' with two dots on a Volkswagen windshield, indicating it was produced in February 2019. The location may vary depending on the model, so pay attention to both the driver's and passenger's sides. When cleaning the glass, make sure dirt doesn’t obscure the markings. Checking the date is crucial for determining whether the glass was replaced after an accident. I’d recommend checking it during routine maintenance—if you can’t figure it out, just ask a technician at a repair shop; they can decode it in seconds. This can help you avoid being tricked when buying a used car.
Was this review help?
18
3
Share
Expand All
Grant
10/22/25 7:33am
I'm obsessed with studying Volkswagen details. To find the glass production date, look for the DOT mark on the edge of the glass. A number like 8 might represent 2018. The dot system determines the month - if the dot is in the decimal position, count which dot it is to get the month (e.g., one dot on the left means January). It's usually located in the corner of the windshield, often on the passenger side - don't miss any tiny characters. This simple method helps determine glass age, letting you spot potential issues when buying used cars and avoid accident vehicles. I often share such tips on car forums - they're actually practical and easy. Just spend two minutes checking, and you can even impress friends by sharing this knowledge.
Was this review help?
7
0
Share
Expand All
More Forum Discussions

What to Do When the Brakes of Roewe 350 Are Hard?

When the engine is not working, the braking system can only rely on the residual vacuum boost, which usually runs out after a few presses. However, this issue will be resolved after restarting the engine and is not considered a fault. Restart the engine and then try to press the brake pedal firmly to reactivate the system. If the vacuum check valve is faulty, the vehicle needs to be towed to a repair shop. If you find it very hard to press the brake pedal while driving, it is likely due to a failure of the brake booster pump.
8
3
Share

How to manually reset the tire pressure on the Roewe ei6?

When the ignition switch is off, press and hold the "Reset" button. Turn on the ignition switch. Release the "Reset" button and briefly press the "Clock Adjustment" button once. Press the "Clock Adjustment" button four times, and the multifunction display will show the interval mileage until the next maintenance.
11
4
Share

What to Do When a Mercedes-Benz C200 Fails to Start After Power Loss?

If the battery has been disconnected or is low on power, pull the switch upward until the side window is completely closed, and hold the switch in this position for 1 second. Hold the switch in the closing direction until the roller blind is fully closed, then continue holding the switch for another 1 second, and then hold the switch in the opening direction. Hold the switch in the opening direction again until the sunroof opens another 10 centimeters, then release the switch and hold it in the closing direction.
4
2
Share

How to Clear the Maintenance Reminder on Volkswagen Polo?

The method to clear the maintenance reminder on Volkswagen Polo is as follows: 1. First, turn off the engine and remove the car key. 2. Press and hold the right button below the dashboard, then insert the key and turn it to the power-on position without starting the engine. Release the right button once the key is turned to the power-on position, and a small wrench symbol will appear. 3. After the small wrench symbol appears, press the left button below the dashboard. Once the wrench disappears, the dashboard will return to normal display. Here is more information about the Volkswagen Polo: (1) In terms of design, the new-generation Polo features a more flattened look, giving an immediate impression of a sportier transformation. (2) The raised lines on the engine hood and the waistline continue to emphasize a rugged style. (3) The front fascia incorporates larger and more elongated headlights with built-in LED light sources and wavy daytime running lights. The dual-grille design on the front bumper is innovative, complementing the chrome-accented grille, resulting in a clean yet well-layered front end. (4) The new-generation Polo measures 4053mm in length, 1751mm in width, and 1446mm in height, with a wheelbase of 2564mm, an increase of 94mm compared to the current model. The trunk space has been expanded from 280L to 351L. (5) The rear features sharp lines, with LED taillights in a familiar design. The dual single-exhaust-style decorative elements and black rear lip add a sporty touch to the rear end.
11
2
Share

How to Set the Sunroof Initialization Function for the Ford Edge?

With the sunroof fully open, press the arrow A end of the switch to move the sunroof to the mechanical stop point. Press and hold the arrow A end of the switch for more than 10 seconds to complete the initialization. Press and hold the arrow B end of the switch again. The sunroof will automatically run through the full cycle (including the tilt) from the mechanical stop position.
13
4
Share

How to Pass the Subject 2 Driving Test?

It is crucial to maintain a positive mindset and avoid giving up, striving to pass next time. Learn from the experience and analyze the reasons for your failure. Discuss any doubts with your instructor or peers to ensure you don't repeat the same mistakes. The cause may likely be overlooking certain details, such as incorrect sitting posture, poor clutch control, or misaligned reference points, which require focused practice and refinement.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.