How to Check the Fuel Light on an Accord?

1 Answers
VanLayla
07/29/25 11:37pm
Method to view the fuel light on an Accord: This indicator light is located on the fuel gauge. If this light illuminates, it indicates the need to refuel as the remaining fuel in the tank is less than 10.3 liters. Additional information about the fuel light is as follows: 1. The fuel gauge is generally located directly in front of the driver's position. 2. Typically, the vehicle dashboard has four gauges: speedometer, tachometer, temperature gauge, and fuel gauge, each distinguished by a simple icon. The speedometer and tachometer are larger for easy viewing of speed and RPM, while the temperature and fuel gauges are smaller for checking interior temperature and remaining fuel. 3. The vehicle fuel gauge is an indicator that displays the amount of remaining fuel, serving as an important reference for the driver to determine whether to refuel. By understanding the structure and meaning of the fuel gauge, the driver can accurately assess the remaining fuel or whether the fuel gauge is functioning normally.
Was this review help?
17
3
Share
More Forum Discussions

How Many Degrees Should the Steering Wheel Be Turned for Left and Right Turns?

When the car reaches halfway, start turning back. When the turn is halfway completed, with the car body at approximately a 45-degree angle, naturally return the wheel without sudden movements. Below is an introduction to the point deductions for not using turn signals during the Subject 3 driving test: 1. Starting: Failing to use turn signals when starting, turning, changing lanes, pulling over, or before overtaking results in a 10-point deduction. 2. Turning Direction: Turning the steering wheel without waiting for the turn signal to be on for at least 3 seconds results in a 10-point deduction. 3. U-turns: Not using turn signals for a U-turn directly results in a 100-point deduction. Using turn signals for more than 150 meters results in a 10-point deduction, and exceeding 200 meters results in a 100-point deduction. Below is additional information on the Subject 3 test content: 1. Starting: Vehicle preparation, starting, and driving straight. 2. Speed Control: Gear shifting operations, changing lanes, and pulling over. 3. Turning: Going straight through intersections, left turns at intersections, and right turns at intersections. 4. Passing Designated Areas: Crossing pedestrian crossings, passing school zones, and passing bus stops. 5. Vehicle Control: Meeting other vehicles, overtaking, making U-turns, and driving at night.
8
2
Share

What is the fuel tank capacity of the MG GS?

2019 MG GS has a total of 7 models, all with a fuel tank capacity of 55 liters. The vehicle is equipped with either a 1.5-liter turbocharged engine or a 2.0-liter turbocharged engine. The transmission options include a 6-speed manual transmission, a 6-speed wet dual-clutch transmission, and a 7-speed dry dual-clutch transmission. The vehicle adopts front-wheel drive and front four-wheel drive configurations. In the same vehicle class, the 2020 Hanteng X7 has a fuel tank capacity of 60 liters, the 2022 Sehol QX has a fuel tank capacity of 55 liters, and the 2019 MG HS has a fuel tank capacity of 55 liters. During actual refueling, the amount of fuel may exceed the calibrated capacity. This is because the fuel tank capacity marked by the car manufacturer is measured from the bottom of the tank to the safe limit, and there is additional space from the safe limit to the tank opening. This space ensures that the fuel can expand when the temperature rises without overflowing from the tank. If the fuel is filled up to the tank opening during refueling, the actual refueling amount may exceed the calibrated tank capacity. If the owner wants to know the remaining fuel level, they can observe the fuel gauge on the right side of the dashboard, which is marked with E and F. When the pointer is close to E, it indicates low fuel, and when it is near F, it indicates sufficient fuel.
18
2
Share

How to Reset After Changing Brake Pads on BMW 3 Series?

BMW 3 Series brake pad reset method: First, replace the sensor wire, then use a diagnostic computer to reset. Brake pads are a crucial component of the braking system, which consists of a vacuum booster, master cylinder, brake pads, brake discs, and wheel cylinders. When the brake pedal is pressed, the vacuum booster provides assistance. The BMW 3 Series is equipped with a low-power version of a 2.0-liter turbocharged engine, coded as b48b20b, with a maximum power of 135 kW and a maximum torque of 300 Nm. This engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with an 8-speed automatic transmission.
10
5
Share

How to Replace the Car's Cabin Air Filter?

Method for replacing the car's cabin air filter: 1. First, move the front passenger seat backward to create more operating space; 2. The filter is located under the front passenger dashboard, where you can see two protruding plastic clips. Turn them counterclockwise until they come off; 3. Remove the protective sponge panel to reveal the filter compartment cover. Then, slide the cover off to expose the cabin air filter, which can be pulled straight down for removal; 4. Install the new cabin air filter by following the above steps in reverse order. Cabin air quality should not be overlooked, especially in dusty northern areas where the filter can easily become dirty and harbor bacteria. It is essential to regularly clean and replace the cabin air filter.
19
1
Share

How to Open the Car Engine Hood?

Method to open the car engine hood: There is an interior release lever located below the dashboard, opposite the driver's left leg. Pull this lever to unlock the engine compartment hood. Then, pull the small handle extending from the grille or reach under the slightly raised edge of the hood to release the secondary latch, allowing the hood to open fully. If steam or coolant is escaping from the engine compartment, do not open the hood. Wait until there is no steam, smoke, or coolant escaping and the engine has cooled down before attempting to open the hood. After closing the hood, ensure it is properly secured by checking that it is flush with the adjacent body panels.
19
4
Share

Where is Jianghuai Automobile produced?

Jianghuai passenger cars are produced in Hefei, Anhui. Jianghuai passenger cars are manufactured by Anhui Jianghuai Automobile Group Co., Ltd., with its main products including heavy, medium, light, and mini trucks, multi-purpose commercial vehicles, MPVs, SUVs, sedans, buses, special chassis, as well as core components such as transmissions, engines, and axles. Below are relevant details: R&D Capability: Jianghuai Automobile has a high-level R&D team of nearly 5,000 people; it has established a five-tier R&D system, with overseas R&D centers in Turin, Italy, and Tokyo, Japan, and domestic national-level enterprise technology centers and national-level industrial design centers. By the end of 2016, it held 8,732 authorized patents, including 712 invention patents. International Exports: Jianghuai Automobile's international market covers more than 130 countries and regions in South America, Europe, Africa, the Middle East, and Southeast Asia. By the end of 2016, cumulative exports exceeded 450,000 vehicles, ranking fifth in the industry. Among them, Jianghuai light trucks have ranked first in industry exports for 14 consecutive years; in 2014, it signed an export contract for 6,159 heavy trucks to Venezuela, setting the largest single export order for Chinese heavy trucks.
16
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.