How to Check the Engine Number of a Sedan?

1 Answers
MacEmma
07/24/25 6:00pm
Methods to check the engine number of a sedan: 1. Use the owner's name, mobile phone number, vehicle license, license plate number, and the traffic management bureau's website to query; 2. Check through documents such as the vehicle license, motor vehicle registration certificate, purchase invoice, factory certificate, operation certificate for commercial vehicles, and vehicle insurance card; 3. The engine number is usually located near the left spark plug of the car engine. You can see the engine number by opening the car's hood. The engine model consists of the front, middle, rear, and tail sections. It is an identification code assigned by the engine manufacturer in accordance with relevant regulations, corporate or industry practices, and the engine's attributes, used to represent information such as the manufacturer, specifications, performance, characteristics, technology, purpose, and product batch of the engine.
Was this review help?
3
4
Share
More Forum Discussions

Should the Front Brake Disc Be Replaced if It Has Grooves?

Grooves on the front brake disc indicate uneven wear. They can be removed and polished, but replacement is necessary if the grooves are deep. The replacement steps are as follows: 1. Open the engine compartment and check the brake fluid level to ensure it is within the normal range, preventing overflow during the replacement process. 2. Use a jack to align with the support points under the car and raise the vehicle until the tire is completely off the ground, then remove the tire. 3. Use a wrench and socket to remove the bolts of the brake caliper, then take out the brake pads directly. 4. Push the brake piston back in, install the new brake pads, and reassemble the original parts in the reverse order of disassembly. 5. After installation, check the brake fluid level again. Press the brake pedal firmly several times to ensure the fluid level remains within the normal range.
3
3
Share

Which country does the Borgward brand belong to?

Borgward is a German brand, and its models include the BX7, BX7 EV, BX7 TS, BX5, and BX5 TS. Taking the 2020 Borgward BX5 New Edge model as an example, its body dimensions are: 4490mm in length, 1877mm in width, and 1675mm in height, with a wheelbase of 2685mm, a fuel tank capacity of 60 liters, and a minimum ground clearance of 186mm. The 2020 Borgward BX5 New Edge model features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 1.4L turbocharged engine, delivering a maximum horsepower of 150PS, a maximum power of 110kW, and a maximum torque of 250Nm, paired with a 6-speed automatic transmission.
16
0
Share

How to Reinstall a Removed Rearview Mirror?

The installation method for the rearview mirror is: 1. At an angle, use two clips to hook onto the mounting plate fixed on the glass; 2. Lift it upwards to hook the top two clips; 3. Adjust the position as needed. The principle of the rearview mirror is that the angle between the light rays perpendicular to the convex mirror spreads outward like a fan, causing the virtual images of objects farther away to appear smaller in the convex mirror as the fan-shaped angle increases. This allows the convex mirror to accommodate more distant scenery. The manual adjuster for the car rearview mirror consists of a base, a swivel plate, a pressure plate, a guide ring, a spring, and a locking cap. The swivel plate, under the pressure of the base and the spring, creates a certain amount of friction on the hemispherical contact surface. Then, through the directional positioning of the guide ring, the mirror can be easily adjusted by hand and remains stable even under the vibrations of the vehicle.
13
1
Share

What are the key reference points for parallel parking in Subject 2?

Subject 2 parallel parking primarily focuses on 2 reference points: point A at the upper left corner and point C at the lower right corner of the parking space. Below are key considerations for Subject 2 examination: 1. Reverse parking: Main deductions include touching lines during reverse, failing to enter the bay, exceeding time limit, and not following prescribed route. Post-reform regulations require completing reverse parking within 210 seconds (timeout results in failure). The sequence must be right-side reverse first, then left-side reverse. Maintain 30cm margin observation during operation. 2. Parallel parking: Critical deductions involve turn signals, 30cm margin, and line contact. When entering the test area, steer right early to align wiper's highest point with roadside line for 30cm adjustment. Remember the sequence: first full right lock → straighten wheels → full left lock → park → activate left turn signal → check mirrors when exiting to avoid wheel contact. 3. 90-degree turn: Deductions focus on turn signal operation and line contact. Activate signal upon entering test area, then deactivate after voice prompt (10-point penalty for incorrect operation). Maintain 30cm margin like parallel parking. Slightly release clutch at full lock point to prevent stalling. Straighten wheels only after rear wheels clear the turn to avoid line contact.
12
3
Share

What is the solution for the car body not being straight when parking by the side in Subject 3?

Here are the solutions for the car body not being straight when parking by the side: 1. Method one: This is mainly due to insufficient technical skills. Check the rearview mirror to see the angle between the car body and the curb. If they are parallel, the car won't be parked unevenly. 2. Method two: Keep your hands relaxed, lightly hold the steering wheel, and don't use too much force. Look towards the end of the road instead of staring at the front of the car. If the car is slightly off, make minor adjustments and then straighten the steering wheel. When parking, first turn backward. When the car body is about 30 centimeters from the curb, turn the steering wheel to the left. Once the car body is parallel to the curb, straighten the wheel and make minor adjustments. 3. Method three: During practice, mark the middle of the engine hood at the front of the car. When parking by the side, as soon as the mark touches the edge of the road, immediately level the steering wheel. While slowly moving closer to the side, keep an eye on the right front corner of the car to prevent it from colliding with the roadside. Also, check the rearview mirror to adjust the distance between the car body and the roadside. This adjustment action can be recalled from the process of correcting the car body's distance from the sides of the garage during the reverse parking exercise in Subject 2.
11
0
Share

What is the model of the high beam for the Jinyi X3?

The bulb model for the Jinyi X3 high beam is H7 12V 55W halogen bulb. Introduction to Halogen Headlights: The working principle of halogen headlights is the same as that of incandescent lamps, where the tungsten filament is heated to incandescence to emit light. However, halogen headlights are an upgrade over incandescent lamps by incorporating halogen elements such as bromine and iodine. Utilizing the halogen cycle principle, they effectively reduce the wear and tear of the tungsten filament at high temperatures, resulting in higher brightness and longer lifespan compared to incandescent lamps. Introduction to Xenon Headlights: Xenon headlights, also known as 'high-intensity discharge (HID) lamps,' do not have a filament inside the bulb. Instead, they are filled with inert gases like xenon. The performance of xenon headlights is significantly influenced by the ballast. A high-quality ballast ensures quick start-up, resistance to extreme cold, and consistent brightness at low voltages. The color temperature of xenon headlights is closer to daylight, making them much brighter than halogen headlights. This provides drivers with better illumination, enhancing driving safety, while consuming only two-thirds of the energy of halogen headlights. Additionally, xenon headlights have a much longer operational lifespan.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.