How to Check if the Compressor is Good or Bad

1 Answers
IsabelleMarie
07/29/25 1:08pm
To determine whether the car air conditioning compressor is functioning properly, connect the three-way pressure gauge set, start the engine, and observe the gauge readings. If the low-pressure pointer drops rapidly and the high-pressure pointer rises quickly, and when the throttle is increased, the amplitude of these changes becomes more pronounced, it indicates good performance. Below is an introduction to the car air conditioning compressor: 1. Function: The car air conditioning compressor is the heart of the car air conditioning refrigeration system, responsible for compressing and delivering refrigerant vapor. Compressors are divided into fixed displacement and variable displacement types. Based on different working principles, air conditioning compressors can be categorized into fixed displacement compressors and variable displacement compressors. 2. Classification: According to different working methods, compressors can generally be divided into reciprocating and rotary types. Common reciprocating compressors include crankshaft-connecting rod and axial piston types, while common rotary compressors include rotary vane and scroll types.
Was this review help?
4
4
Share
More Forum Discussions

How to Fix a Battery That Won't Charge?

The methods to repair a battery that won't charge are: 1. Check if the charging circuit connection is secure, inspect whether the wiring and plug contacts are intact, examine if there are any signs of arcing or burning in the sockets and plugs, and check for any damaged or broken wires; 2. Inspect the charger for any damage and verify if the charging parameters meet the requirements, i.e., the initial charging current should reach 1.6A to 2.5A per cell; 3. Check if the battery is dry internally, meaning if there is severe electrolyte depletion, and also inspect for irreversible sulfation on the plates; 4. Secure the charging circuit connections firmly and replace any malfunctioning charger; 5. For dry batteries, add pure water or sulfuric acid, perform maintenance charging and discharging to restore battery capacity. If irreversible sulfation is detected, perform equalization charging to recover capacity; 6. For dry batteries after adding electrolyte, the maintenance charging should control the maximum current at 1.8A, charging for 10 to 15 hours, with the voltage of all three batteries ideally above 13.4V. If the voltage difference between batteries exceeds 0.3V, it indicates asynchronous irreversible sulfation, and such batteries require replacement of the entire set or activation.
17
4
Share

What material is the spark plug of the Kia K2 made of?

The spark plug of the Kia K2 is made of nickel alloy, with a lifespan of approximately 20,000 kilometers. The Kia K2 offers two options for its inline 4-cylinder naturally aspirated Gamma series engines: a 1.4L and a 1.6L. Both engines are equipped with CVVT (Continuously Variable Valve Timing) technology and feature an all-aluminum engine construction. The 1.4L model delivers a maximum power of 78.7 kW at 6,300 rpm and a maximum torque of 135.4 Nm at 5,000 rpm. The 1.6L model produces a maximum power of 90.4 kW at 6,300 rpm and a maximum torque of 155 Nm at 4,200 rpm.
3
1
Share

Why is it necessary to replace spark plugs regularly?

Regular replacement of spark plugs is necessary because carbon deposits will accumulate after prolonged use. If not replaced periodically, this can make engine starting difficult, leading to incomplete combustion. Additionally, the voltage that the ignition coil can provide is limited. Even with normally functioning spark plugs, as the electrodes wear down, the voltage required to bridge the spark plug gap continuously increases. This may cause misfiring during rapid acceleration, high-speed driving, or heavy loads, resulting in vehicle vibration, acceleration difficulties, and fuel wastage. Therefore, regular replacement of spark plugs is essential to maintain optimal engine performance and improve fuel efficiency.
7
0
Share

How to Remove the Armrest Box of Mazda 3?

The method to remove the armrest box of Mazda 3 is as follows: 1. Remove the screws inside the armrest box of Mazda 3; 2. Firmly grip the gear shift handle next to the armrest box and pull it upwards to release the fixing clip of the gear shift; 3. Use a pry tool to pry open the joint between the storage box panel and the armrest box; 4. Pry open the clips on both sides of the car armrest box and lift the armrest box upwards to remove it. Mazda 3 is a compact car launched by Mazda, offering two powertrain options: a 1.5L and a 2.0L naturally aspirated engine. The 1.5L engine has a maximum power of 86kw and a maximum torque of 148 Nm; the 2.0L engine has a maximum power of 116kw and a maximum torque of 202 Nm.
9
4
Share

How to Clear the Tire Pressure Warning?

Methods to clear the tire pressure warning: 1. Check and confirm whether the tire pressure is normal. If there is an issue, adjust it to the standard pressure, then drive a few kilometers. Generally, the system will automatically reset at this point; 2. If the tire pressure is confirmed to be normal, visit a car service shop to inspect the tire pressure sensors and clear the fault code; 3. Locate the settings button on the central console for manual reset, usually by pressing the SET key. If the tire pressure warning light comes on due to low tire pressure while driving, immediately reduce speed, avoid sharp steering and sudden braking, and find a safe place to stop and inspect the tires. Both excessively low or high tire pressure can trigger the tire pressure warning light. When the warning light comes on, the first consideration should be to restore the tire pressure to normal levels before addressing the warning light. The tire pressure warning light typically comes on due to the following situations: 1. A punctured tire; 2. Excessive tire pressure; 3. Prolonged driving with low tire pressure; 4. Tire pressure dropping due to long periods without inflation.
12
1
Share

What impact will a faulty front oxygen sensor have on a car?

A faulty front oxygen sensor will prevent the electronic fuel injection system's computer from obtaining accurate information about the oxygen concentration in the exhaust pipe, significantly affecting the car's air-fuel ratio. This can lead to increased fuel consumption by the engine, higher exhaust emissions, and even the direct emission of black smoke. Over time, issues such as unstable engine idle, misfires, and surging may become more frequent. Automobile oxygen sensors are actually divided into two types—front and rear—with the three-way catalytic converter serving as the boundary. The sensor before the three-way catalytic converter is the front oxygen sensor, while the one after it is the rear oxygen sensor. The role of the front oxygen sensor is to detect the oxygen concentration in the engine's exhaust gases and then transmit the obtained information in the form of an electrical signal to the ECU. The ECU uses this oxygen concentration information to perform feedback control on the air-fuel ratio. This not only effectively controls exhaust emissions, thereby reducing the car's environmental pollution, but also improves the quality of fuel combustion in the engine, which can help lower the car's fuel consumption.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.