How to Change the Engine Oil for a Magotan?

1 Answers
VonRyder
07/30/25 10:45am
Steps to change the engine oil for a Magotan: 1. Run the engine until it reaches operating temperature, then use a jack to lift the vehicle, engage the handbrake, and secure the front wheels with wooden wedges; 2. Place an old oil container under the oil pan, locate the oil pan drain bolt, and slowly loosen it; 3. Move the oil container beneath the oil filter, use an oil filter wrench to loosen the filter, and unscrew it by hand; 4. Apply new engine oil to the gasket of the new filter; 5. Pour new oil into the oil pan, lower the vehicle, check the oil dipstick, and start the engine. In terms of exterior design, the main changes for the Magotan are concentrated on the front fascia, where the grille retains the classic chrome horizontal trim but now features a raindrop-patterned chrome decoration inside. The interior sees minimal changes, with more straight lines adopted in the cabin. The minimalist design style continues to exude a familiar business-oriented ambiance.
Was this review help?
3
0
Share
More Forum Discussions

What is the car brand with the L logo?

L is the logo of Lexus, a luxury brand under Toyota. Here is some extended information about Lexus: 1. Lexus offers both SUVs and sedans. Its sedan lineup includes models like the IS, ES, GS, etc. The LS is a full-size luxury sedan, competing in the same segment as the BMW 7 Series, Mercedes-Benz S-Class, and Audi A8L. 2. The Lexus LS measures 5235mm in length, 1900mm in width, and 1450mm in height, with a wheelbase of 3125mm. 3. The LS is powered by a 3.5L naturally aspirated V6 engine producing 220kW of maximum power and 350Nm of peak torque. The engine reaches its maximum power at 6600rpm and peak torque at 5100rpm. It features VVT-i and VVT-iW technologies and utilizes an aluminum alloy cylinder head and block.
17
4
Share

What are the differences between Toyota Izoa and CHR?

Toyota CHR belongs to GAC Toyota, while Izoa belongs to FAW Toyota. The knowledge about Toyota Izoa and CHR is as follows: The differences between Toyota Izoa and CHR: The lower grille of Izoa adopts a simple horizontal bar style paired with a silver lower guard plate decoration; while the CHR's lower grille features a more sporty honeycomb grille. The engines of Toyota Izoa and CHR: Both use a 2.0L naturally aspirated engine designed for the TNGA architecture series, with a four-cylinder structure. The maximum power output can reach 171 horsepower, with a maximum torque of 203 Nm. The maximum torque speed is 4400-4800 rpm, and the maximum power speed is 6600 rpm.
4
0
Share

How to Reactivate a Failed ETC?

ETC reactivation method after failure: Insert and remove the ETC card twice consecutively until the electronic tag screen displays "Bluetooth On". If "Tag Invalid" appears when inserting/removing twice without the electronic tag attached, this is normal and does not affect reactivation. Alternatively, you can directly press the button on top of the electronic tag to enable Bluetooth. Turn on your phone's Bluetooth, open the corresponding mobile APP (usually with a download QR code on the electronic tag), and enter the device activation interface. Click "Device Connection" and wait patiently for the "Connection Successful" prompt. After successful connection, upload a photo of the vehicle's front to complete activation. ETC installation positions: For small vehicles like cars and minivans, the ETC card and OBU device should be installed on the upper middle part of the front windshield. For large vehicles like trucks and buses, the installation position is on the lower middle part.
20
0
Share

How to Replace the Cabin Air Filter in a Buick Excelle?

First, open the engine compartment hood and disconnect the intake air quality sensor wiring harness connector from the intake air quality sensor. Release the mass air flow sensor wiring harness securing clip from the cabin air filter housing. Remove the front outlet pipe clamp of the cabin air filter. Detach the front outlet pipe of the cabin air filter from its housing. Remove the five bolts securing the cabin air filter housing, then separate the upper housing from the lower housing to access and remove the cabin air filter. Below are relevant details about replacing the cabin air filter: 1. If the airflow from the air conditioning vents significantly decreases, the cabin air filter may be clogged. First, clean the filter or replace it if necessary. 2. Cleaning frequency depends on road conditions, and it is recommended to clean it sooner rather than later. 3. The cabin air filter must be correctly installed in its designated position. Operating the air conditioning without the filter may degrade dustproof performance and affect system efficiency. 4. In cities with poor air quality, it is advised to replace the cabin air filter twice a year to safeguard your health.
2
2
Share

What is the RPM of Emgrand GL at 120 km/h?

When the Emgrand GL reaches a speed of 120 km/h, the engine RPM is 2200. The engine speed is related to the number of work cycles per unit time or the effective power of the engine, meaning the effective power of the engine varies with different speeds. Below is relevant information about engine speed: 1. The effective power specified on the engine product nameplate and its corresponding speed are referred to as the rated power and rated speed, respectively. 2. The operating condition of the engine at rated power and rated speed is called the rated condition. The rated power is not the maximum power the engine can produce but the maximum usable limit of effective power determined based on the engine's purpose. 3. For the same model of engine, the rated power value may differ depending on its intended use. Effective torque also varies with the engine's operating condition. Therefore, the maximum torque a car engine can output and its corresponding speed are used as indicators to evaluate the engine's dynamic performance. Typically, a speed sensor is used in conjunction with the signal teeth on the flywheel to measure the engine's speed.
19
5
Share

What to Do When You Discover a Flat Tire on the Right Side While Driving?

If you notice a flat tire while driving, turn on your hazard lights and pull over to the side of the road to change the spare tire. After replacing the tire, control your speed and do not exceed 80 km/h. Once you find a tire shop to repair the tire, replace the spare tire with the repaired one, as spare tires are not meant for long-term use. Below are the steps for changing a tire: 1. After parking and turning off the engine, engage the handbrake; 2. Place heavy objects in front of and behind the wheel to prevent rolling, and set up a triangular warning sign behind the vehicle; 3. Use a wrench to loosen the lug nuts of the flat tire in a diagonal pattern; 4. Position the jack on the side of the flat tire and lift the vehicle to a certain height; 5. Remove the lug nuts and take off the flat tire; 6. Install the spare or new tire and tighten the lug nuts in a diagonal pattern; 7. Lower the vehicle by releasing the jack and ensure all lug nuts are securely tightened.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.