How to Cancel the Chery Car Maintenance Reminder?

[BeauLynn]

Canceling the Chery car maintenance reminder is done as follows: Insert the key, press and hold the small button on the right (the black lever on the dashboard used to adjust time and reset mileage), turn the key to ON (note that you do not need to start the engine), then continue holding the small button for a few seconds before releasing it. Press and hold the small button again, gently rotate it to the right, and then release it to remove the maintenance reminder. Chery Automobile is a state-controlled enterprise engaged in automobile production, headquartered in Wuhu City, Anhui Province. The company's products cover passenger cars, commercial vehicles, and microcars. Taking the Tiggo 7 as an example, its body dimensions are 4505mm in length, 1837mm in width, and 1670mm in height, with a wheelbase of 2670mm. In terms of exterior design, the Tiggo 7 features a dynamic waistline on the side of the body, resembling the waves created by a speedboat cutting through water. The two waistlines extend from the rear to the turn signal with bold and striking lines, giving the steel body a vibrant sense of motion.

[LeEmmanuel]

I'm the kind of person who enjoys DIY car repairs. Canceling the Chery maintenance reminder is actually quite simple, with the common method being manual operation via the dashboard buttons. Start the car but don't press the accelerator, leaving it in ACC mode; then locate the MODE or TRIP button on the steering wheel and hold it for a few seconds until the screen menu pops up; switch to the maintenance settings option, select reset reminder or clear message, and you're done. The specific button sequence may vary by model, such as differences between the Arrizo and Tiggo series, so I recommend checking the owner's manual or following online videos step by step. Remember to do this step only after maintenance, otherwise the reminder will be disabled but the actual car condition won't be updated. If you make a mistake, you can always visit the 4S shop where they'll reset it for free using an OBD tool. This DIY task saves time and hassle, but take it slow and steady to ensure safety.

[StGenevieve]

When I first bought my Chery car, I was really annoyed by the constant illumination of the maintenance light. After some exploration, I figured out how to handle it. In most cases, there's a maintenance reset function on the dashboard. You need to turn the ignition to the ON position without starting the engine, then use the multifunction steering wheel buttons to navigate into the menu, find the maintenance item, and select reset. The button positions may vary depending on the car model—my approach is to pause first and check the manual or a TikTok tutorial. Before resetting, make sure the maintenance has been completed to avoid misjudging the mileage. If you're unsure, don't worry—just drive to the repair shop, and they'll fix it quickly. Remember, regular maintenance is good for the engine, and keeping the reminders active is essential—don't cancel them arbitrarily. This process taught me a lot, and now I'm quite confident in handling minor car issues.

[LeCarmen]

Veteran drivers have plenty of experience, turning off the maintenance light is a piece of cake. For Chery cars, usually turn the ignition to ACC, hold the TRIP button on the dashboard to enter the menu, and select reset maintenance reminder. If the button fails, using an OBD diagnostic tool to plug into the interface for reset is the fastest. The key point is not just to cancel but to skip maintenance—safety first. The steps are simple with no technical terms, fellow car enthusiasts can give it a try. There are plenty of online resources, but make sure the maintenance has actually been done. Some newer models require entering sub-menus, which is slightly more complicated but takes very little time.

[LaThomas]

I pay great attention to details, so cancel reminders with caution. First, ensure the engine oil and filter have been replaced before proceeding. Chery's reset process generally involves starting to RUN mode, long-pressing the steering wheel button to bring up settings, locating the maintenance item, and selecting clear. Steps are similar across different models, but the manual is the bible. If issues arise, visiting a 4S store is worry-free and not expensive. Alternatively, check online community shares to avoid mistakes. The maintenance reminder itself is a protective mechanism—after resetting, the light goes off, but don't forget the cycle to keep the car more durable. The entire process emphasizes safety; don't rush, check each step carefully.

[StDonovan]

From a practical perspective, I've studied Chery's maintenance reminder mechanism. It's recorded by the onboard computer, and you can turn off the light by resetting it. The operation involves turning the ignition to the ON state, using the steering wheel controls to enter the information menu, and selecting reset maintenance. Specifically, such as holding down the RESET button in combination with other buttons, the details vary by model—the Arrizo might be a bit more complicated than the Tiggo. Why is there a reminder? To prevent missing maintenance which could affect engine lifespan. After resetting, verifying with an OBD tool is convenient and recommended for those with some technical knowledge. In short, once you understand the principle, the operation is easy. Remember, maintenance is the core—don't just cancel the reminder without performing actual maintenance to keep the car in healthy condition.