How to brake when driving a motor vehicle with ABS system?

1 Answers
LeMadeline
07/29/25 6:38pm
You can step on the brake pedal firmly, but when steering while emergency braking, the vehicle may still skid. Additionally, do not rely on ABS to shorten the braking distance, especially during emergency braking on icy or snowy roads, as ABS cannot effectively reduce the braking distance. Benefits of ABS braking: 1. Reduced danger: Vehicles without ABS are prone to wheel lock-up when emergency braking in critical situations, increasing the risk coefficient and potentially leading to severe consequences. The ABS system helps shorten the braking distance. 2. Safe driving: During braking, ABS quickly determines the wheel lock-up state based on speed signals from each wheel speed sensor. It closes the normally open input solenoid valve for the wheel that begins to lock up, maintaining the braking force. If the wheel continues to lock up, the normally closed output solenoid valve is opened, causing the braking pressure on that wheel to rapidly decrease due to the direct connection to the brake fluid reservoir, preventing the wheel from completely locking up due to excessive braking force.
Was this review help?
19
1
Share
More Forum Discussions

What happens if the parking brake is not released while driving?

Consequences of driving with the parking brake engaged: 1. The rear brake discs overheat, producing a burning smell. In severe cases, the brake discs may turn red, leading to significant brake fade and reduced braking performance. 2. Severe wear on the brake pads, shortening their lifespan. 3. Noticeable increase in fuel consumption, sluggish acceleration, and a dragging sensation when releasing the throttle. 4. Uneven tire wear. Even on the same vehicle, the braking capacity of the four tires is not identical, resulting in uneven tire wear. 5. Increased temperature of the brake fluid, leading to reduced braking performance.
13
5
Share

What does unpaved road mean?

Generally refers to roads other than Class A or Class B highways. Below is more information about unpaved roads: 1. Introduction: Unpaved roads are those without surface materials like slabs or concrete bricks, directly consisting of concrete surfaces, asphalt roads, or even dirt roads, gravel roads, etc. 2. Paved roads: Unpaved roads are defined in contrast to paved roads. Paved roads with a thickness of 2.5~4cm are a widely used road structural layer, typically serving as the wearing course for multi-layer asphalt surfaces, thin overlays in maintenance and repair, and pavement for bridge decks.
6
0
Share

What does ABS stand for?

Automotive ABS stands for Anti-lock Braking System. Its function is to automatically control the braking force of the brakes during vehicle braking, preventing the wheels from locking up and maintaining a state of rolling while slipping (with a slip ratio of around 20%), ensuring maximum adhesion between the wheels and the road surface. The following is an introduction to the ABS system: 1. The ABS system consists of components such as the ABS module, ABS master cylinder, oil pipes, and wheel speed sensors. 2. During braking, the ABS quickly determines the wheel lock-up state based on the speed signals from each wheel speed sensor, closing the normally open input solenoid valve on the wheel that is starting to lock up, keeping the braking force unchanged.
4
2
Share

What is the Drag Coefficient of a Car?

The drag coefficient of a car is a function of the Reynolds number, and the air resistance of the car is directly proportional to the drag coefficient. This means that the larger the drag coefficient, the greater the resistance the car experiences while driving. The magnitude of air resistance a car encounters during driving is related to many factors, such as exterior design and chassis design. The lower the car's chassis, the smaller the air resistance during driving. Additionally, the flatter the car's chassis, the less resistance it will experience. Car owners can observe the chassis of supercars; these vehicles have their chassis completely sealed with protective panels. The chassis of supercars is extremely flat and very low.
13
2
Share

What Causes the Horn to Stop Working After Vehicle Wading?

When a vehicle's horn stops working after wading through water, the reason is typically that most vehicle horns are installed near the front bumper. During wading, external water can enter the high or low-frequency horn, altering the sound. More details are as follows: 1. If you notice a change in the horn's sound, the first step is to remove the horn, either by yourself or at a professional repair facility. After removal, clear any accumulated water inside the horn and allow it to dry. 2. If the horn returns to normal after this process, it can continue to be used. However, if the horn still doesn't work after treatment, the damaged horn will need to be replaced.
15
0
Share

Which part of the car window should be struck with a safety hammer?

When a driver needs to break the window for emergency escape, they should first attempt to shatter the side window. Below is additional information about safety hammers: 1. Function: In the event of an accident where the vehicle is sealed and the doors are too damaged to open due to strong impact, using a safety hammer to break the window can help passengers escape. In such situations, the safety hammer essentially becomes a "life-saving hammer." 2. Usage: Safety hammers are typically installed in easily accessible locations within enclosed spaces like cars. In emergencies such as fires or submersion in water, the hammer should be taken down, held firmly, and the metal head used to strike the four corners and edges of the glass. This is because tempered glass is strongest in the center, making the corners and edges the weakest points.
3
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.