How to automatically close the trunk of Audi A6L?

2 Answers
DeGabrielle
07/25/25 3:38am
Audi A6L does not have a trunk opening device inside the car (all models). If you need to open the trunk, you have to wait until the car is parked and pull it manually. The specific location is in the groove directly below the four rings (right above the middle of the license plate). Here are the details: 1. Audi uses a touch-sensitive switch, which can be opened with a light touch (the groove between the two license plate lights). 2. Additionally, the remote key can also open the trunk (after turning off the engine and removing the key). Press and hold the "car logo" button in the center of the remote key (the one between unlock and lock) for 3 seconds, and the trunk will automatically unlock but not open directly. You still need to lift it manually. Finally, you can also open the trunk directly with the key.
Was this review help?
11
4
Share
StAdriana
08/10/25 5:04pm
I've been driving this car for three years, and the automatic trunk closing operation is actually quite simple. When you stand at the rear of the car, press the close button on the inner side of the trunk lid, wait a few seconds, and it will slowly lower and lock itself. Using the key remote is also very convenient—just press and hold the trunk button on the key for 3 seconds, and the lid will automatically close. The height memory function is especially practical. You can stop the lid at a preferred position based on your habit, then press and hold the close button for 5 seconds until you hear a beep. After that, the lid will automatically stop at that height every time it closes. Just be careful not to place items that are too tall inside the trunk, as the sensors may trigger the anti-pinch function and cause the lid to bounce back. Also, remember to regularly clear snow from the guide rails in winter, otherwise the operation may become sluggish.
Was this review help?
19
5
Share
Expand All
More Forum Discussions

Method for Resetting the Maintenance Reminder on the 2018 Discovery Sport

Method for resetting the maintenance reminder on the 2018 Discovery Sport: 1. With the engine turned off, press and hold the short-distance trip counter reset button located below the tachometer. 2. Turn the ignition to the ON position, then release the short-distance trip counter reset button. The display will show the "SERVICE" indicator. 3. Pull out the minute button on the clock and turn it to the right. The mileage will appear on the display. 4. Turn off the engine to reset the reminder message. 5. Turn the ignition to the ON position again, and the "SERVICE" indicator should disappear.
8
3
Share

Is the Driver's Card One Card per Vehicle?

Driver's cards are not issued on a one-card-per-vehicle basis; generally, it's one card per person. Below is relevant information about automotive driver's cards: 1. Definition: The Motor Vehicle Driver Traffic Safety Information Card is an electronic information carrier that records basic information about a driver's traffic violations, penalty points, traffic accidents, and traffic safety education. It enables quick verification of the authenticity of a driver's license information and allows on-site payment of traffic violation fines. 2. Benefits: The driver's card provides services such as traffic violation inquiries, self-service handling of violations, SMS notifications of violations, and vehicle inspection reminders. When traffic violations occur, drivers no longer need to visit traffic violation processing centers to pay fines.
12
1
Share

What is the difference between Mercedes-Benz GL and GLS?

Here are the differences between Mercedes-Benz GL and GLS: 1. Exterior: 1. Front grille: The Mercedes-Benz GL features a dual-slat grille design, while the GLS has a dual-slat perforated grille design. 2. Lighting: The GL comes with xenon smart headlights, whereas the GLS uses an LED lighting system. 3. Wheels: The GL is equipped with 20-inch wheels, while the GLS has 21-inch light alloy wheels. 2. Powertrain: 1. The GLS is paired with a 9-speed automatic transmission, while the GL comes with a 7-speed automatic transmission. 2. The GLS adds two configurations: side impact protection and front passenger airbags.
17
0
Share

Can the driver's license photo cover the eyebrows?

No. Exposing the ears and eyebrows is a basic requirement for the photo. Below is extended information regarding the size requirements for driver's license photos: 1. Portrait requirements: A recent front-facing, bareheaded, colored, single-person half-length small one-inch photo of the driver's license applicant taken within the last 6 months. 2. Driver's license photo dimensions: The photo size should be 3.2cm × 2.2cm, with the head length between 1.9cm and 2.2cm, and the head width between 1.4cm and 1.6cm, on a white background. 3. Dress code: No uniforms should be worn in the photo, and the image should be clear and natural in appearance.
18
5
Share

What Type of Driver's License is Required to Operate a Fire Truck?

According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" issued by the Ministry of Public Security, a B2 driver's license is required to operate a fire truck. Here are the details: 1. Fire Truck: A fire truck is a specialized vehicle, also known as a fire engine, primarily used to perform firefighting tasks. Fire trucks come in various types with complex functions and can be classified according to different standards. Based on the chassis load capacity, they include mini fire trucks, light fire trucks, medium fire trucks, and heavy fire trucks. 2. B2 Driver's License: The B2 driver's license can be obtained directly by applying for the test, or it can be upgraded from a C1 license.
1
5
Share

Where is the turn signal fuse located in a Toyota Crown?

The turn signal fuse of the Crown is located in the fuse box in the front engine compartment. Introduction to turn signals: 1. Turn signals are important indicator lights that are activated when a motor vehicle turns to alert surrounding vehicles and pedestrians. 2. The turn signal bulbs use xenon tubes, controlled by a microcontroller circuit, with alternating left-right flashing for continuous operation. Reasons why turn signals may not work: 1. If the turn signals don't light up but the hazard lights do, the turn signal switch may be partially damaged. 2. If individual turn signals don't light up, the bulb may be burnt out and replacing it can solve the problem. 3. If all bulbs don't light up, the turn signal fuse may be blown, causing all turn signals to fail.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.