How to align the camshaft VVT wheel position on a Ford Mondeo?

1 Answers
ONicole
07/30/25 6:47am
Ford Mondeo camshaft VVT wheel alignment method is as follows: 1. There is a screw on the right front half-turn and the cylinder block, remove it, then find another screw to screw in, which is used to fix the crankshaft, ensuring that the No. 1 cylinder piston is at top dead center, then remove the valve cover. 2. Place a steel plate behind the two camshafts, which is used for timing alignment, and then the chain can be installed. 3. After installation, tighten the two screws of the crankshaft and camshaft. When fixing the crankshaft, note that there is a 6-hole screw hole on the crankshaft pulley, which should be aligned with the point on the timing cover, this is used for ignition signal alignment. After assembly, remove the screws and steel plate.
Was this review help?
15
2
Share
More Forum Discussions

Should rear passengers fasten seat belts on highways?

Rear passengers on highways are required to fasten seat belts. According to Article 51 of the Road Traffic Safety Law of the People's Republic of China, when a motor vehicle is in motion, both the driver and passengers must use seat belts as stipulated. Violations by drivers will result in a 500 yuan fine and 2 penalty points, while passengers not wearing seat belts properly will be fined according to the same regulation without penalty points. The following precautions should be taken on highways: 1. Pay attention to signage when entering highways; 2. When passing through toll booths and entering the ramp, maintain speed below 40 km/h, do not overtake, turn on the turn signal, and observe traffic flow on the main lane until entering the acceleration lane to speed up.
16
0
Share

Why is the wheel hub hot to the touch?

The wheel hub becomes hot due to friction between the brake disc and brake pads, which is a normal phenomenon. The maintenance methods for wheel hubs are: 1. Clean the wheel hub frequently to prevent salt from corroding the aluminum surface; 2. When the wheel hub temperature is high, allow it to cool naturally before cleaning. Do not use cold water for cleaning as it may damage the aluminum wheel hub, cause deformation of the brake disc affecting braking performance. Using detergent to clean the wheel hub may cause chemical reactions on the surface, resulting in loss of luster. The wheel hub is the rotating part where the tire's inner contour steel connects to the wheel core via pillars, serving as the metal component that supports the tire's center mounted on the axle.
12
4
Share

What are the exterior differences between the Phantom and Ghost?

The exterior differences between the Phantom and Ghost are: The chrome window trim of the two cars is different. The Phantom uses a regular narrow double-line electroplated inscription, giving it a more square and rugged visual effect, while the Ghost features a wide single-line trim, appearing more rounded and youthful. The new Ghost adopts a double trim design. The front ends of the Phantom and Ghost are also different, both utilizing large Greek column-style grilles, with the Ghost's grille being rounder. The design styles of the two cars differ; both designers employed Western mythological themes. The Phantom continues the family's classical design heritage, while the Ghost introduces some changes to the family design concept, leaning towards a more contemporary style.
7
3
Share

Can a driver's license be transferred to another city?

To transfer a driver's license to another city, you need to go to the vehicle management office in the destination city. Please note the following regulations for driver's license transfer: 1. The applicant must come in person to handle the transfer and sign on the spot; it cannot be delegated to others. 2. Required documents: "Resident ID Card"; non-locals must also provide a local temporary residence permit. 3. If the transfer is obtained through fraudulent or bribing means, the driver's license will be revoked, and the applicant will not be allowed to apply for a driver's license for three years. 4. The following three reasons allow for direct transfer: (1) If the household registration is moved to the city, the driver's license can be directly transferred along with the household registration. (2) If the driver's license was obtained during university studies in another city, it can be directly transferred.
9
0
Share

How to Calculate Fuel Consumption per 100 Kilometers for a Car?

Algorithm for fuel consumption per 100 kilometers: Fuel consumption per 100 kilometers equals fuel consumption (liters) divided by driving distance (kilometers) multiplied by 100. Fuel consumption per 100 kilometers refers to the fuel consumption of a vehicle traveling at a constant speed for 100 kilometers on the road, which is a basic theoretical indicator of the vehicle. Fuel consumption has always been a concern for many car owners, so how is the fuel consumption per 100 kilometers calculated? Under normal circumstances, the formula for calculating fuel consumption per 100 kilometers is: stage fuel consumption * 100 / stage mileage. For example, your fuel consumption would be 88L * 100 / 723 kilometers = 12.17L per 100 kilometers. Here, stage fuel consumption divided by stage mileage equals fuel consumption per kilometer, multiplied by 100 is the fuel consumption per 100 kilometers.
5
0
Share

Which is the Brake and Which is the Accelerator in a Car?

Automatic transmission cars and manual transmission cars have different positions for the brake and accelerator. The specific differences are as follows: 1. Automatic transmission cars: (1) There are only two pedals, from left to right, which are the brake and accelerator pedals. (2) The left foot controls all pedals throughout. When driving, you either press the brake or the accelerator, and these two actions cannot occur simultaneously. 2. Manual transmission cars: (1) There are three pedals, from left to right, which are the clutch, brake, and accelerator pedals. (2) The left foot controls the clutch, while the right foot controls the brake and accelerator pedals. During driving, it is easy to confuse the brake and accelerator, so always pay attention to the position of your right foot to avoid mistaking the accelerator for the brake.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.