How to Adjust When the Side of the Vehicle is Too Far from the Curb Line?

How many seats can a B2 driving license drive for passenger vehicles?

A B2 driving license allows driving blue-plate minibuses with 9 seats or fewer and a vehicle length under 6 meters. The vehicle types permitted under a B2 license include heavy-duty, medium-duty trucks or large, heavy, and medium-sized special-purpose vehicles. Heavy-duty and medium-duty trucks are primarily trucks, while large, heavy, and medium-sized special-purpose vehicles refer to vehicles equipped with specialized devices or equipment, such as sprinkler trucks, concrete mixer trucks, fire engines, etc. Other vehicle types permitted under a B2 license include C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed trucks), C4 (three-wheeled cars), and M (wheeled self-propelled machinery).

12

5

Share

What is the top speed of the Jinjila 300?

The top speed of the Jinjila 300 is 143 km/h. Below are the detailed specifications of the Jinjila 300: Models: The Jinjila 300 comes in two variants: the Standard version and the High-end version. Powertrain: The Jinjila 300 is equipped with a V-twin cylinder liquid-cooled electronic fuel injection engine. This engine features a four-valve-per-cylinder design, delivering a maximum power of 22.5 KW and a peak torque of 25.3 N.m. Features: The Jinjila 300 is outfitted with dual-channel ABS, belt drive, an LCD instrument panel, LED lighting, and semi-hot melt tires.

2

4

Share

Is It Serious If the Half Shaft Dust Cover Is Seeping Oil?

Leakage from the half shaft dust cover is not a major issue, but it is best to inspect and repair it promptly. Here is an introduction regarding leakage from the half shaft dust cover: Causes of leakage: Overfilling of the drive axle reducer with oil, causing the oil level to exceed the normal height. Resulting hazards: Leakage from the half shaft oil seal will reduce the amount of lubricating oil in the drive axle, affecting normal lubrication and accelerating wear on components, leading to premature damage. Leakage from the half shaft oil seal allows lubricating oil to flow into the wheel-side reducer, increasing the oil level in the wheel-side reducer, damaging the oil seal, and flowing into the brake drum, resulting in poor braking performance and endangering safe driving.

8

3

Share

Under what circumstances does Audi's active braking system activate?

Audi's active braking system officially activates at speeds above 30km/h. It uses radar waves to monitor blind spots that are difficult for drivers to observe, providing voice signals to alert drivers to pay attention to driving safety or actively applying the brakes. The active braking system is highly practical for urban congested roads and traffic light intersections. Vehicle safety systems are mainly divided into two types: active safety systems and passive safety systems. Below is a related introduction: 1. Active safety systems: Active safety systems include electronic devices such as ABS and ESP. 2. Passive safety systems: Passive safety systems involve vehicle body energy-absorbing structures, seat belts, airbags, etc.

10

2

Share

New Focus Coolant Replacement Tutorial?

New Ford Focus antifreeze replacement tutorial is as follows: 1. First, park the vehicle for a period of time before performing the replacement operation to prevent burns from the antifreeze. 2. Keep the car idling while continuously adding clean water to the antifreeze storage tank, allowing the water to flush out residual antifreeze in the cooling system. 3. After the water is completely drained, tighten the drain valve and then turn off the engine. At this time, add antifreeze to the reservoir, filling it between the MIN and MAX scale lines. 4. Start the engine again, as the air in the cooling system is expelled during idling, the antifreeze level will drop. 5. Wait for a while until the liquid level no longer changes, then supplement the antifreeze to between the two scale lines. The antifreeze replacement process is now complete.

2

5

Share

Where is the location to add windshield washer fluid in a Volkswagen Sagitar?

The location to add windshield washer fluid in a Volkswagen Sagitar is on the lower right side of the engine compartment, with a cap marked with a washer symbol. The operating steps are as follows: 1. Open the engine compartment hood. On the left side, there should be two white reservoirs with blue caps. The one with the smaller opening at the bottom is for the windshield washer fluid. Open this cap and directly add the washer fluid. 2. After filling, securely close the cap and shut the engine compartment. When the Sagitar's engine hood is opened, there are two reservoirs with blue caps on the upper left side. 3. The one with the smaller cap is where you add the windshield washer fluid. In low-temperature climates, a special antifreeze should also be added to prevent the washer fluid from freezing.

10

5

Share

How to Adjust When the Side of the Vehicle is Too Far from the Curb Line?

How many seats can a B2 driving license drive for passenger vehicles?

What is the top speed of the Jinjila 300?

Is It Serious If the Half Shaft Dust Cover Is Seeping Oil?

Under what circumstances does Audi's active braking system activate?

New Focus Coolant Replacement Tutorial?

Where is the location to add windshield washer fluid in a Volkswagen Sagitar?

Where Should the Red Cloth Be Placed in the Car?

How to Turn Off Car Wiper?

Can the fragrance system be retrofitted?

How to Turn on the Air Conditioning in a Mazda?