How to adjust the time on Tiggo 3?

1 Answers
Larry
07/24/25 10:08pm
The method to adjust the time on Tiggo 3 is: 1. Turn the key to the ACC position or remove it, at which point the instrument panel will turn off; 2. Turn the light switch again to turn on the parking lights; 3. The instrument panel backlight will illuminate, press and hold the instrument button for a while, the hour display on the instrument panel will start flashing, then release the button and press it again, each press increases the hour by one; 4. After adjusting the hour, without touching the button, the hour display will flash 5 times and automatically switch to minutes, each press of the button increases the minute by one, holding it down will continuously increase, after adjustment, without touching the button, the minute display will flash 5 times and then stop. In terms of interior, the Tiggo 3 features a three-spoke steering wheel with moderate size and good grip, complemented by lead-gray decorative strips, giving an overall good impression, which also reflects the high precision of the manufacturing molds.
Was this review help?
13
5
Share
More Forum Discussions

What does it mean when the natural gas meter shows 'valve closed'?

When the natural gas meter displays 'valve closed', it means there may be insufficient balance due to unpaid fees, or it could be caused by low pressure or insufficient battery power in the electronic gas meter. The solution is to replace the batteries and reinsert the gas card to reopen the solenoid valve inside the gas meter, otherwise there will still be no gas supply. Reasons why the natural gas meter shows 'valve closed' despite having balance: 1. Insufficient pressure. The gas meter must close the valve when pressure is too low to prevent accidents. This requires contacting the gas supplier to resolve, as only they can control the gas supply pressure or repair the pipeline. 2. Low battery in the electronic gas meter. The electronic gas meter has an electrically controlled valve inside. It controls the valve opening based on detected pressure, automatically closing the valve when pressure is insufficient. However, when the battery is low, the detection probe malfunctions and the pressure signal becomes weak. The LCD display consumes very little power, so it may show normal readings with 'low pressure' displayed, and will close the valve when the battery level drops further.
11
1
Share

What Are the Benefits of Forged Wheels?

Forged wheels are currently the most advanced method of manufacturing aluminum rims. The benefits of forged wheels are as follows: 1. Stronger and more durable, enhancing safety. Forged aluminum wheels are 1-2 times stronger than cast aluminum wheels and 4-5 times stronger than standard steel wheels. They are more impact-resistant, with significantly better toughness and fatigue strength compared to cast wheels, reducing the risk of shattering or breaking and improving safety. 2. Lightweight for better fuel efficiency. The reduced weight significantly improves suspension response speed, allowing the suspension system to react more quickly and handle road imperfections more effectively. 3. Fuel savings and superior heat dissipation. According to Japanese experiments, reducing the weight of a five-seat car by 1kg can save approximately 20L of gasoline per year. Forged wheels also dissipate heat more efficiently, preventing brake drums and tires from aging prematurely during long-distance high-speed driving, thereby extending their lifespan and reducing the risk of blowouts. 4. Enhanced handling performance. Upgrading to forged wheels without affecting steering or vehicle fitment—especially when increasing rim width—can noticeably improve acceleration, braking, and cornering sensitivity.
11
3
Share

How to Use Accord Remote Start?

First, use the smart key remote to start the car engine unidirectionally from a distance. After the doors are locked, press the lock button, then hold the HOLD button to start. The steps for Accord remote start are as follows: 1. First, understand what "unidirectional remote engine start" means—it allows you to use the smart key remote to start the car engine unidirectionally from a distance. 2. Then, to start the engine remotely, after the doors are locked, press the "Lock" button, then hold the "HOLD" button. 3. If the vehicle is not started, the engine will run for a maximum of 10 minutes. To extend the running time by another 10 minutes during the first run, press the "Lock" button, then hold the "HOLD" button again. 4. If the request to extend by 10 minutes is successfully transmitted a second time, the car's turn signals will flash three times as a reminder.
4
2
Share

How to Reset the Maintenance Light on the Boyue?

There are two methods to reset the maintenance light on the Boyue: First Method: 1. Start the car; 2. Press the "SET" button to enter the instrument settings interface; 3. Find the "Maintenance Reset" setting in the settings interface; 4. Click to confirm the reset. Second Method: 1. Start the car, and after the dashboard lights up, press the TRIP key on the left side of the control lever to activate the instrument buttons; 2. Use the volume key on the right side of the steering wheel to switch to the settings system; 3. Press the "MODE" key to enter the settings system; 4. Use the "Left/Right Cycle" buttons on the steering wheel to find the maintenance mileage option; 5. Press the "MODE" key to enter the maintenance mileage system; 6. At this point, there are two options on the interface: "Return" and "Reset". Use the "Left/Right Cycle" key to select the "Mileage Reset" option and press the "MODE" key to confirm; 7. The system will then reset the maintenance mileage.
2
5
Share

How many kilometers should the brake fluid be replaced for the Regal?

The brake fluid replacement interval for the Buick Regal is 30,000 kilometers, using Mobil brand DOT4 fluid. Below are the steps for replacing the brake fluid in the Buick Regal: 1. First, prepare an oil extraction container for the brake fluid. If possible, avoid using the method of pressing the brake pedal, as this makes it difficult to completely drain the old fluid. 2. Extract the old brake fluid from the reservoir in the engine compartment, which takes about 10 seconds. 3. Then, use the extraction container again to remove residual brake fluid and air from the lines. 4. Connect the hose of the extraction container to the bleeder valve of the wheel cylinder. Once connected, begin extracting the remaining brake fluid. 5. While extracting the brake fluid, have another person continuously add new brake fluid at the filler port. Under pressure, the new fluid will push out the old fluid, and this also prevents air from increasing in the lines due to lack of fluid. 6. The extraction process typically takes about 8-10 minutes. After completion, add brake fluid to the appropriate level on the dipstick, close the cap, and start the engine to test the brake performance. Press the pedal multiple times consecutively; if it feels soft, continue bleeding the air.
9
1
Share

How to Take a Motorcycle License Test?

Motorcycle license tests consist of a theory exam and a road test. The road test mainly assesses the rider's balance control of the motorcycle. During the test, attention should be paid to the coordination of throttle and clutch, with an emphasis on maintaining slow speeds rather than going too fast. The details are as follows: 1. Theory Exam. The motorcycle subject one question bank contains 500 questions, with 50 randomly selected for the exam, each worth 2 points, and a passing score of 90. Subject four has 292 questions, with 50 randomly selected, each worth 2 points, and a passing score of 90. In some regions, motorcycle subject one and subject four are taken simultaneously, with 50 questions randomly selected from both question banks as the test paper, each worth 2 points, and a passing score of 90. 2. Road Test. Motorcycle subject two involves slalom around cones, where four poles are placed in a straight line, requiring the rider to navigate through them in an S-shape and then return, without touching the ground with their feet, stalling the engine, or crossing the lines. Generally, subject two and subject three are taken together, and some regions do not test subject four.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.