How to adjust the time on Dongfeng Fengguang 580?

1 Answers
Samantha
07/29/25 1:54pm
Dongfeng Fengguang 580 time adjustment method: There is a button labeled "CL" on the center console. Press left to make the hour or minute flash, and press right to adjust the numbers. After adjusting the time, press "CLK" to confirm. The adjustment mode will exit automatically after a few seconds of inactivity. The Dongfeng Fengguang 580 is an SUV under the Dongfeng brand, with body dimensions of 4715mm in length, 1845mm in width, and 1715mm in height, and a wheelbase of 2780mm. The Dongfeng Fengguang 580 offers two engine options: a 1.8-liter four-cylinder naturally aspirated engine and a 1.5-liter four-cylinder turbocharged engine.
Was this review help?
2
4
Share
More Forum Discussions

How to Use Cruise Control in a Car?

Steps to use cruise control in a car: 1. Locate and press the cruise control button on the steering wheel; 2. When the car reaches the desired cruising speed, press the set button downward; 3. After setting the cruise control speed, you can press the button upward or downward to fine-tune the cruising speed; 4. While using cruise control, always pay attention to road conditions. When the cruise control function is activated, you can press the accelerator to make the speed reach or exceed the lower limit of the cruise control speed. After confirming the activation of the cruise control function, the engine fuel will be automatically supplied to meet the power demand for the current speed.
19
1
Share

Can the clutch of Baojun 360 be adjusted?

Baojun 360 is equipped with a hydraulic clutch, which can be adjusted for lightness or heaviness, but the adjustable range is relatively small. The clutch only requires minor adjustments when it wears out over time. If you wish to adjust it, you can loosen the screw below and manually pull the movable rod indicated by the arrow upward to its limit, while simultaneously pulling the connector originally fixed between the two screws downward to eliminate the gap distance in the linkage mechanism. Currently, there are two scenarios for adjusting car clutches: 1. Minor adjustments can be made by adjusting the clutch control part, but the hydraulic clutch control part is not adjustable. Mechanical clutches can be adjusted by modifying the tightness of the clutch cable or by changing the length of the clutch cable (altering the leverage). The former method allows for minor adjustments, while the latter offers a larger adjustment range. However, the latter method falls into the category of modification, and improper adjustment may affect driving safety, so it is not recommended. 2. It could also be due to component failure, requiring the replacement of related parts. Mainly, issues may arise with the clutch pressure plate, clutch disc, or release bearing, commonly referred to as the "clutch three-piece set." These components are consumable parts, and if they are faulty or severely worn, the clutch may become excessively heavy. Often, a heavy clutch is caused by problems with the "clutch three-piece set." Generally, the service life of the "clutch three-piece set" is similar, so it is best to replace all parts at the same time when necessary.
12
0
Share

What does sync mean on a car?

sync refers to the synchronization button of the dual-zone automatic air conditioning, and it is very simple to turn on and off. Press the sync button, and the temperature of the air outlets on both sides of the car will be the same and adjusted synchronously; when the air conditioner is turned on, if the temperatures on both sides are set differently, the sync will automatically turn off. Here are some related introductions about sync: 1. sync is the button to cancel the temperature synchronization on both sides, allowing the temperatures on both sides to be independent of each other, so there will be a dual-zone effect where the left side can blow hot air while the right side can blow cold air. 2. As long as the temperatures on both sides are different, the SYNC button will light up. At this time, pressing SYNC again will immediately make the air conditioning temperature on the passenger side the same as that on the driver's side, and then turning the passenger's temperature knob to change the temperature will still light up the SYNC. That is, the passenger's temperature will change with the driver's temperature, but the driver's temperature will not change with the passenger's temperature.
12
1
Share

What Are the Causes of Engine Stalling and Shaking at Idle?

The causes of engine stalling and shaking at idle are: 1. Throttle blockage, carbon buildup, or abnormal opening; 2. Carbon buildup or blockage in the fuel injectors; 3. Spark plugs being burnt or damaged; 4. Use of low-quality gasoline leading to fuel pump blockage; 5. Incomplete combustion of the air-fuel mixture in the cylinders. Solutions for engine stalling and shaking at idle: 1. Regularly clean the throttle; 2. Periodically clean the fuel injectors to prevent carbon buildup; 3. Replace the spark plugs; 4. Use gasoline from reputable gas stations. When the engine starts and runs well from low to high speeds but stalls immediately after releasing the accelerator pedal or first becomes unstable and then stalls, this phenomenon can be identified as an idle stalling fault.
7
1
Share

What are the hidden features of the Sylphy?

The hidden features of the Sylphy include: 1. Lock/unlock sound settings; 2. Automatic trunk opening/closing; 3. One-touch window up/down function; 4. Automatic locking function; 5. Automatic unlocking when the engine is turned off; 6. Remote headlight shut-off; 7. Automatic locking if not entered. The Sylphy is a car under Dongfeng Nissan, with its full English name being SYLPHY. Taking the Sylphy 2021 Classic 1.6XE Manual Comfort Edition as an example, it is equipped with a 1.6L 122 horsepower L4 naturally aspirated engine, paired with a 5-speed manual transmission. Its body dimensions are: length 4631mm, width 1760mm, height 1503mm, with a wheelbase of 2700mm.
6
4
Share

Is it acceptable to skip 4S dealership maintenance for cars?

It is acceptable to skip 4S dealership maintenance for cars. Vehicle maintenance items include core components and wear-prone parts. Core components consist of the chassis, engine, and transmission, while wear-prone parts include engine oil and oil filters, spark plugs, cabin air filters, tires, brakes, and lights. The replacement intervals for car maintenance parts are as follows: 1. Engine oil and oil filters should be replaced every 5,000 kilometers; 2. Cabin air filters should be replaced every 20,000 to 30,000 kilometers; 3. Spark plugs should be replaced every 20,000 kilometers; 4. Brake pads should be replaced every 50,000 kilometers.
12
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.