How to Adjust the Seat Belt of a Goodbaby Car Seat?

1 Answers
MarcusLee
07/30/25 8:39am
Goodbaby car seat belt adjustment method: Press the adjuster button and pull the seat belt to adjust it to the appropriate length. The seat belt of the car seat is set according to the baby's age. If the baby is smaller, the seat belt can be tightened a bit. Below is a detailed introduction to the adjustment method: 1. Determine the installation method based on the baby's condition: use rear-facing for babies under 8 kg and forward-facing for those over 18 kg. 2. For forward-facing installation, the seat faces the direction of the car's movement, and the backrest angle is adjusted to the first or second gear; for rear-facing installation, the seat faces away from the direction of the car's movement, and the backrest angle is adjusted to the third gear. 3. Thread the seat belt, insert the waist belt into the installation guide slot, and insert the shoulder belt into the upper guide slot. 4. Pass the waist belt around the bottom of the car seat and insert it into the rear-facing installation guide slot on the other side. 5. Insert the seat belt tongue into the buckle and tighten the seat belt immediately.
Was this review help?
7
0
Share
More Forum Discussions

Where is the lift mode for the Mercedes-Maybach S400?

The lift mode for the Mercedes-Maybach S400 is located on the MMI control panel. Press the CAR button, then the SETUP button, and the lift mode will appear to be activated. Lift Mode: To deactivate the lift mode, push the adjustment switch upward to the standard height and hold it for 30 seconds until the instrument panel displays that the function is turned off. The lift mode is one of the vehicle's configurations, which adjusts the chassis height from the ground through the air suspension system. Exterior: The vehicle dimensions are a length of 4918mm, a width of 1983mm, a height of 1696mm, a wheelbase of 2895mm, and a fuel tank capacity of 90 liters. Configuration: The drivetrain is front-engine four-wheel drive, and both the front and rear suspensions use multi-link independent suspension.
19
0
Share

What Causes the Squeaking Noise in the Rear Suspension of Geely GL?

Geely GL rear suspension squeaking is caused by loose front wheel chassis screws. MacPherson Strut Independent Suspension: The MacPherson strut suspension is one of the most widely used front suspensions in passenger cars today. It consists of a coil spring, shock absorber, and lower control arm, with most models also including a stabilizer bar. The MacPherson strut suspension is simple in structure, making it lightweight and responsive. Multi-link Suspension System: The multi-link suspension system includes control arms, rear positioning arms, upper arms, lower arms, and front positioning arms. The control arms can adjust the rear wheel toe-in. The advantages of the multi-link suspension are its simple construction, light weight, and reduced space occupation by the suspension system.
7
1
Share

How to reset the tire pressure warning light on Wuling Journey?

The tire pressure monitoring warning will be displayed on the instrument panel screen of the Wuling Journey. Click the tire pressure monitoring warning to pop up the SET button, then press and hold the SET button to reset the tire pressure light. The following is an introduction to tire pressure monitoring: Tire pressure monitoring automatically monitors tire pressure in real-time during vehicle operation and alerts drivers about tire leaks or low pressure to ensure driving safety. There are two common types: 1. Direct tire pressure monitoring system: Uses pressure sensors installed in each tire to directly measure tire pressure, transmitting pressure data wirelessly from inside the tire to a central receiver module, then displaying each tire's pressure data. The system automatically alerts when tire pressure is too low or there's a leak. 2. Indirect tire pressure monitoring system: When a tire's pressure decreases, the vehicle's weight causes that wheel's rolling radius to become smaller, making it rotate faster than other wheels. By comparing rotational speed differences between tires, it monitors tire pressure. Indirect systems actually rely on calculating tire rolling radius to monitor pressure.
8
0
Share

What are the solutions for Emgrand engine immobilizer authentication failure?

Solutions for Emgrand engine immobilizer authentication failure: Take out the car remote key, place it against the one-touch start button, then while keeping it pressed against the one-touch start button, press the unlock button on the remote key to resolve. Immobilizer-related hardware faults: If hardware components related to the immobilizer system, such as the electronic immobilizer control unit, immobilizer wiring harness, or alarm horn, malfunction, the dashboard will display a prompt indicating that the immobilizer system requires repair. This usually appears during startup. False alarm faults: SCS security system false alarm faults. The alarm prompt will disappear immediately after an actual restart, in which case it can be ignored. Alternatively, refreshing the SCS security software may help. Refreshing the security software is free during the 4S store warranty period. After the warranty expires, you can negotiate, and it is generally still possible to get it refreshed for free.
12
0
Share

Is there a mandatory retirement age for cars now?

Currently, there is no mandatory retirement age for cars, but there are still some restrictions. Here is an introduction to the knowledge about retirement age: 1. Private cars: Private cars include 5-seater sedans and 7-seater SUVs. Small and micro non-operational vehicles have no usage period, but when the mileage reaches 600,000 kilometers, the state will guide them to be retired. 2. Operational vehicles: Taxis have a usage period of 8 years, and when the time is up, they will be mandatorily guided to retire. Domestic pickup trucks are mandatorily retired after 15 years. Medium-sized taxi passenger vehicles have a usage period of 10 years, and when the time is up, they will be mandatorily guided to retire. Heavy, medium, and light-duty trucks have a usage period of 15 years, and when the time is up, they will be mandatorily guided to retire. Semi-trailer tractors have a usage period of 15 years, and when the time is up, they will be mandatorily guided to retire. Micro trucks have a usage period of 12 years.
6
3
Share

Can the Reiz be driven with the VSC light on?

The Reiz can be driven normally with the VSC light on. Below is an introduction to the Reiz: 1. Exterior Design: The REIZ Reiz's exterior design is captivating. It achieves a dynamic and elegant beauty with the best body proportions, combining agility and the luxurious dignity unique to high-end sedans. The body surface is glossy, rich, and full, breaking through the traditional concepts of vehicles in its class. It creates a futuristic and mesmerizing appearance, striving for perfection with the best body proportions and perfect structure for an FR sedan. 2. Interior Space: The Reiz surpasses its peers in terms of premium feel. It pursues the perfect interior space of the REIZ Reiz, illuminated by self-illuminating instrument panels. The dark instrument panel paired with a silver center console sets a sporty and fashionable tone. While there are no standout features in the design, the atmosphere is enhanced by meticulously crafted details.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.