···
Log in / Register

How to adjust the rearview mirror of GAC Trumpchi GS4?

3 Answers
SanJayden
07/29/25 11:06pm
GAC Trumpchi GS4 rearview mirror adjustment method: 1. On the left side below the vehicle's steering wheel, there is a round button. Rotate it to the L position, then move the button up, down, left, or right to adjust the angle of the left mirror; 2. Rotate the button to the R position, then move it up, down, left, or right to adjust the angle of the right mirror; 3. After adjusting to the desired position, rotate the button to the middle position to turn off the adjustment. The GAC Trumpchi GS4 is positioned as an international new-generation SUV, with a total of 8 models available. In terms of body dimensions, its length, width, and height are 4510mm, 1852mm, and 1708mm respectively.
Was this review help?
15
0
Share
LaLane
08/16/25 1:09am
When adjusting the rearview mirrors of my GAC Trumpchi GS4, I always make it a habit to do so after parking and settling in steadily, without rushing to hit the road. There's a small panel on the inner side of the door with buttons labeled L and R—press L to adjust the left mirror and R for the right one. Gently press the directional buttons with your fingers, and the mirror lens will move up, down, left, or right. I prefer setting the mirror angle to show just a little bit of my car's rear wheel, which minimizes blind spots when reversing or changing lanes, making it much safer. Remember to sit upright and avoid leaning, as that can skew your perspective. Once, I made a mistake adjusting them—the mirror was angled too high, and I nearly hit a pillar while reversing at night. Since then, I’ve always double-checked the adjustment. Additionally, it’s best to fine-tune them before rainy or foggy weather to ensure clear visibility. Properly adjusted mirrors are the first step to safe driving and can save you a lot of trouble.
Was this review help?
19
4
Share
Expand All
Tamara
10/18/25 6:56am
As a GS4 owner, I find the rearview mirror adjustment quite straightforward. After sitting in the driver's seat, I simply locate the control buttons on the door panel, select L or R to begin adjusting, and press the buttons slowly to move the mirror to the desired position. I prefer setting it to show a bit of the rear window and the ground, which helps with more accurate reversing. Some beginners might rush and adjust the mirror too wide, leaving blind spots uncovered, which can be dangerous. I recommend practicing in open spaces like garages or empty lots, testing the adjustments after making them. The GS4 features electric controls with responsive buttons, but avoid adjusting the mirrors while driving—always stop safely to make adjustments. During regular maintenance, also check the mirror cleanliness, as accumulated dust can impair visibility.
Was this review help?
5
2
Share
Expand All
More Forum Discussions

What are the steps to replace car coolant?

The steps to replace car coolant are: 1. Open the vehicle's engine compartment hood, and you can see the coolant reservoir in the upper right corner; 2. Open the coolant drain plug under the radiator to drain the old coolant; 3. Add new coolant, tighten the cap, and the coolant replacement is complete. Functions of coolant: 1. Provides anti-corrosion protection for cooling system components; 2. Prevents scale buildup, avoiding reduced radiator efficiency; 3. Ensures the engine operates within the normal temperature range. Precautions for using coolant: 1. The coolant level needs to be checked regularly and replenished promptly if it falls below the lower limit; 2. Observe whether the coolant has any turbid sediment, and replace it promptly if there is; 3. Different vehicle models have different coolant colors, and they should not be mixed; 4. Before winter, measure the freezing point of the coolant to prevent it from freezing.
20
4
Share

Where is the reversing radar module located on the Kia K2?

The Kia K2 reversing radar control box is located at the rear of the vehicle. The radar main unit is positioned on the radar head attached to the trunk lid, specifically at the left rear of the trunk, on the side with the lights, mounted on the wheel arch sheet metal above the wheel. The unit with five wires connected to it is the one. Here is additional information: 1. Reversing Radar: Its full name is 'Reverse Anti-Collision Radar,' also known as 'Parking Assist Device.' It mainly consists of ultrasonic sensors, a controller, and a display (or buzzer). 2. Automatic Activation of Reversing Radar: When the gear lever is shifted into reverse, the reversing radar automatically starts working. If the radar detects that the distance to an obstacle behind is too close, the buzzer or display device of the reversing radar will issue a warning to remind the driver to pay attention to the rear distance control.
1
3
Share

What is the actual 0-100km/h acceleration time for the RAV4 2.0L?

The 0-100km/h acceleration time for the RAV4 equipped with a 2.0L engine is 10.9 seconds. Introduction to 0-100km/h acceleration: 0-100km/h acceleration refers to the time taken to accelerate from 0 to 100 kilometers per hour, which is the most intuitive reflection of a vehicle's power. 0-100km/h acceleration is not the universal standard for vehicle power: Among vehicles with the same displacement, models equipped with turbocharged engines generally have a significant advantage in 0-100km/h acceleration because they deliver more powerful output and have a very wide range of maximum torque output, allowing the vehicle to achieve maximum acceleration at very low RPMs. However, 0-100km/h acceleration is not the ultimate standard for reflecting a vehicle's power performance, especially when the acceleration times of two vehicles are close.
6
1
Share

Where is the engine number located on the Dongfeng Tianlong?

The engine number of the Dongfeng Tianlong is located on the front left side of the engine, in the middle, on the flat surface where the engine block meets the transmission housing. It is typically a combination of 7 to 8 digits and letters. In addition to the above method, the engine number can also be found in the following 4 ways: The vehicle's driving license will have the engine number printed, usually on the second-to-last line; The motor vehicle registration certificate will record the engine number; The car purchase invoice will record the engine number; The vehicle purchase tax payment certificate will record the engine number. It is important to note that the engine number is not the same as the engine model. The engine model refers to the specifications and size of the engine within the manufacturer's range, and engine models can be the same. The engine number, however, refers to the production number of the engine, and each engine can only have one unique engine number, with no two engines sharing the same number.
4
3
Share

What causes the Cadillac ATSL daytime running lights not to work?

Possible reasons for the Cadillac ATSL daytime running lights not working include the daytime running lights being turned off, a blown fuse for the daytime running lights, wiring harness failure, guide ring driver failure, or issues with the daytime running light bulbs. Below are detailed explanations and solutions: Daytime running lights turned off: The daytime running lights may be disabled in the vehicle settings. Simply enable them in the settings. Blown fuse for the daytime running lights: If both left and right lights are not working, replace the fuse. Wiring harness failure: Park the vehicle and inspect the wiring harness between the headlight control module and the daytime running lights. If the issue persists, visit a professional repair shop. Guide ring driver failure: For example, the driver connector may be loose or poorly connected. Secure the driver connector properly. Daytime running light bulb issue: If the bulb filament has quality issues, its resistance may increase with temperature, causing the working current to decrease and the daytime running light to turn off. Replace the bulb.
7
4
Share

What is required for the six-year exemption from inspection and the two-year label replacement?

For the six-year exemption from inspection and the two-year label replacement, you will need the original vehicle license and a copy of the compulsory traffic insurance policy, among other materials. Documents required for vehicle annual inspection (individual): Original vehicle license, copy of the compulsory traffic insurance policy, photocopy of ID card, and the vehicle. Documents required for vehicle annual inspection (organization): Original vehicle license, copy of the compulsory traffic insurance policy, Organization Code Certificate of the People's Republic of China (with fresh seal), letter of authorization (with fresh seal), photocopy of the agent's ID card, and the vehicle. Note: For vehicles eligible for the exemption from inspection and issuance of the inspection qualification label, you only need to go to the vehicle management office, motor vehicle registration service station, or traffic police squadron to fill out the "Motor Vehicle Inspection Label Application Form" and then receive the motor vehicle inspection qualification label and vehicle license.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.