How to adjust the high beam height of the Sylphy?

1 Answers
JosieRose
07/30/25 1:15am
The high beam adjustment button for the Sylphy is located on the lower left side of the steering wheel. Turn on the high beam switch, then rotate the knob upward to raise the beam height and downward to lower it. The "0" setting is the highest position, "1" reduces the height by one level, "2" is a relatively lower position, and "3" is the lowest setting. Here is some relevant information about adjusting the high beam height of the Sylphy: 1. When driving without heavy loads/luggage or on flat roads, choose the normal position "0". 2. If the number of passengers or the load/luggage in the car changes, the headlight axis may be higher than the normal position.
Was this review help?
15
4
Share
More Forum Discussions

How to Open the Trunk of the Trumpchi GS4?

Methods to open the trunk of the Trumpchi GS4: 1. Press the small button located below the trunk, and the trunk will open; 2. If the remote key holder is within approximately 1.0 meters of the trunk, pressing the switch button on the remote key will open it. The Trumpchi GS4 is a compact car under GAC Motor, with body dimensions of 4545mm in length, 1856mm in width, and heights of 1668mm and 1700mm. It is equipped with a 1.5T turbocharged engine, featuring an L-type cylinder arrangement, and is paired with either a 6-speed manual transmission or a 7-speed dual-clutch transmission.
9
0
Share

How to Clear the Tire Pressure Monitoring Warning Light When Tire Pressure is Normal?

Tire pressure normal elimination of tire pressure monitoring warning light method: The tire pressure warning light indicates that there is an issue with your tire pressure, possibly due to a tire being underinflated or punctured, causing a discrepancy in pressure compared to the other tires. It is recommended to check the tire pressure of all four tires. You can reinflate and adjust the tire pressure. After ensuring all tires are in good condition and the tire pressure is normal (all four tires should have the same pressure, typically between 2.4-2.6 BAR or 230-240 kPa), the warning light can be cleared. In summer, the tire pressure can be slightly lower, or if you frequently drive on rough roads, the tire pressure can also be slightly lower. Once the tire pressure is normal, there are several ways to clear the tire pressure warning light, depending on the car brand. Some cars have a physical button that can be pressed and held to clear the warning, or the option to clear the warning light may be available in the dashboard settings. What to do if tire pressure is insufficient: If no damage is visible on the car's tires, simply inflate them to the normal pressure and reset the tire pressure system. If a puncture is found during inspection, drive to a repair shop to have the tire patched before reinflating it. If the tire pressure warning reappears after some time despite no visible puncture, it may be due to a leaking rim caused by deformation. It is recommended to check the rim and replace it if necessary. How tire pressure monitoring works: It uses pressure sensors installed inside the tires to measure the tire pressure and wireless transmitters to send the pressure information from inside the tire to a central receiver module.
3
1
Share

Why does the reversing radar keep beeping at first?

The reasons why the reversing radar keeps beeping at first: 1. There is foreign matter stuck on the reversing radar probe, causing signal blockage; 2. The rear wiper water pipe is leaking or water has seeped into the reversing radar system; 3. The radar ultrasonic signal is faulty, causing false alarms; 4. The reversing radar circuit is short-circuited or the radar module is malfunctioning. Solutions for the reversing radar constantly beeping: 1. Check if there is any foreign matter blocking the radar holes at the rear of the vehicle; 2. Seal the leak or replace the pipe, then drain any accumulated water in the radar system; 3. Restart the engine, drive the vehicle to an open area and try reversing again to observe the effect; 4. Take the vehicle to a 4S shop or repair shop for inspection, checking the circuits or replacing the radar module.
3
4
Share

What does 55d23l on the battery mean?

55d23l on the battery refers to: 55 indicates the ampere-hour capacity of the battery, d represents the battery size, specifically a width of 17.3 cm and a height of 20.2 cm, 23 denotes the front length of the battery as 23 cm, and l indicates that the positive terminal of the battery is on the left. Battery maintenance methods include: 1. Start the car periodically to charge the battery; 2. Add distilled water or a special replenishing fluid when the electrolyte is low; 3. Regularly check if the small holes on the battery cover are ventilated during daily driving; 4. Inspect the positive and negative terminals for signs of oxidation; 5. Check all parts of the circuit for aging or short circuits; 6. Turn off all electrical devices when leaving the car.
13
0
Share

What material are the spark plugs used in the Volkswagen Lavida made of?

Volkswagen Lavida uses nickel-plated copper spark plugs. Spark plugs, commonly known as sparking plugs, function by discharging the pulsed high-voltage electricity delivered through the high-tension leads, breaking down the air between the two electrodes of the spark plug to generate an electric spark, thereby igniting the air-fuel mixture in the cylinder. The Volkswagen Lavida is a sedan produced by Shanghai Volkswagen, which not only maintains the excellent quality of German design but also incorporates many aesthetic concepts reflecting traditional Chinese culture and cutting-edge design elements. The exterior dimensions of the Volkswagen Lavida are length 4670mm, 4541mm, and 4613mm; width 1806mm and 1765mm; height 1474mm, 1488mm, and 1460mm; with a wheelbase of 2688mm and 2610mm. The body structure is available as a 4-door, 5-seater sedan and a 5-door, 5-seater hatchback.
17
5
Share

Does the Haval H6 use a timing belt or a timing chain?

Haval H6 uses a timing belt. The function of the timing belt is to transmit the force of the crankshaft to drive the water pump and charging generator components. The steps to remove the timing belt are: 1. Lift the car with a jack; 2. Remove the engine bottom plate; 3. After removing the bottom plate, the timing belt will be visible; 4. Remove the exposed old timing belt; 5. Install a new timing belt; 6. The timing belt replacement is complete. The installation method of the timing belt is: 1. Loosen the generator fixing screws and the timing belt tension adjustment screws; 2. Push the generator towards the engine to minimize the distance between the timing pulleys, then align and place the timing belt; 3. Adjust the tension of the timing belt to the appropriate level, then tighten the engine fixing screws and adjustment screws.
15
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.