How to Adjust the Headlights of Geely New Vision?
4 Answers
Geely New Vision can be adjusted via the knob at the rear of the headlight assembly, allowing owners to adjust the lights themselves using tools. Lift the engine hood, locate the adjustment knob at the back of the headlight assembly, and use the appropriate tool for adjustment. Before adjusting, determine whether the knob controls left-right or up-down movement. The following precautions should be noted when adjusting the headlights: 1. Choose a dim environment: such as an underground parking lot or at night. Park the car facing a wall, ensuring the front of the car is aligned with the wall and about 5-6 meters away. 2. Cover one headlight with an opaque thick cloth: Adjust each headlight individually. To ensure the light beam position is correct for normal driving, avoid adjusting with the vehicle unloaded; having a friend sit in the driver's seat is recommended. 3. Mark the headlight position on the wall: Also mark the position on the wall corresponding to the car emblem (center of the front). Measure the distance from each headlight mark to the center mark; the distances should be equal. If the lights are tilted outward or inward, refer to the vehicle's manual and use a screwdriver for fine adjustments to ensure the headlights are symmetrically aligned. 4. Adjust the beam height appropriately: The right headlight should be level, while the left headlight should be raised about 10cm, but not too high to avoid blinding oncoming drivers.
As a DIY enthusiast, I personally adjusted the headlights of my Geely New Vision. The method is simple: first, park the car on level ground facing a wall, about five meters away. Open the hood and locate the adjustment screws at the back of the headlight assembly—usually one controls height and the other controls left-right alignment. Use a regular screwdriver to turn them slowly: counterclockwise to raise the beam for longer distance, clockwise to lower it and avoid dazzling oncoming traffic. Keep the light center level with the ground during adjustment, ensuring it's neither too high nor too low. I recommend doing this at night with the lights on to observe the beam position on the wall: ideally, the light spot should be centered and slightly downward, not exceeding the height of the headlights. After adjustment, test drive at night to ensure clear and safe visibility. If unsure, ask a friend for help—one person operates the lights from inside the car while the other observes the details outside. Regular checks prevent misalignment from bumps, extending bulb life and saving electricity and money—proper angles improve light efficiency. Remember not to over-adjust, as it may narrow the beam range or cause malfunctions.
I remember driving for several years, and headlight adjustment is no trivial matter—safety first. The adjustment for the Geely New Vision is conveniently located in the engine compartment: locate the adjustment holes behind the light assembly, with two screws controlling vertical and horizontal alignment. Use a manual screwdriver to adjust: turning counterclockwise raises the beam for better highway illumination over longer distances, while turning clockwise lowers it for shorter-range urban driving. Every time I adjust, I park facing a wall, aligning the center of the light beam with a ground reference line—ensuring it’s not too high to blind others or too low to miss road hazards. Always turn off the engine and lights before adjusting to avoid burns or electrical risks. It’s best to perform a quick check during routine maintenance, as vibrations can easily misalign the lights. If the deviation is significant, testing with the lights on may reveal scattered or unfocused beams, indicating recalibration is needed. This simple task prevents nighttime accidents and reduces bulb burnout—proper alignment extends component life and ensures safer driving. You can do it yourself, saving a trip to the repair shop.
When I first bought my Geely New Vision, I paid close attention to the headlight settings. The adjustment process was straightforward: under the hood, the headlight assembly has screw holes for adjusting height and level using a screwdriver. Park the car facing a wall, then slowly turn the screws to center and lower the beam. The adjustment standard is to ensure the light doesn’t exceed the lower edge of others’ windshields—preventing glare for safety. Personal tip: higher settings suit off-road use, while lower settings are better for city driving. The whole process takes about five minutes, avoiding prolonged exposure of the electrical circuits. Don’t skip regular checks; recalibrate after bumpy roads to ensure clear nighttime visibility.
