How to adjust the headlights of Dongfeng Fengxing T5?

1 Answers
McGriffin
07/30/25 4:07am
Enter the car and locate the headlight height adjustment knob. To set the headlights to the highest position, turn the knob to the "0" position for headlight height.
Was this review help?
5
4
Share
More Forum Discussions

Where to Turn on Audi Headlights?

There is a switch on the left side of the cabin. Turn the switch to turn on the headlights, or you can set it to auto mode (auto) for added safety. When the lights are on, push down the lever on the left side of the steering wheel to turn on the high beams. Models: Audi's main products include: A1, A3, A4, A5, A6, A7, A8, Q1, Q2, Q3, Q5, Q7, Q8, TT, R8, and the S and RS performance series. The A1 is positioned as a small car, the A3 as a compact car, the A4 as a mid-size car, the A6 as a mid-to-large-size car, and the A8 as a luxury sedan. Introduction: Audi is a luxury car brand under Volkswagen Group in Germany. With high production standards, guaranteed quality, and strong innovation capabilities, it has created many classic models. It enjoys high popularity in China and is one of the members of BBA.
12
3
Share

What transmission is used in the Audi A6 in Germany?

Audi A6 uses the Stronic 7-speed dual-clutch transmission, which comes in both manual and automatic versions. Working principle of manual transmission: The shift clutch is a wet multi-plate clutch. When hydraulic pressure presses the driving plates and driven plates together via the piston, the clutch engages. When the working fluid is discharged from the piston cylinder, the return spring causes the piston to retract, disengaging the clutch. Working principle of automatic transmission: After the engine starts, the crankshaft drives the pump impeller to rotate via the flywheel. The centrifugal force generated by rotation causes the working fluid between the impeller blades to be thrown from the inner edge to the outer edge.
8
1
Share

Where to Position the Jack When Changing a Spare Tire on the Baojun 730?

When changing a spare tire on the Baojun 730, the jack should generally be positioned on the raised section of the side rail near the tire being replaced. Prepare the tools: Gather the necessary tools for changing the spare tire, including a wrench and a jack. Position the jack under the vehicle: Place the jack under the vehicle, where there is a designated slot for the jack. Replace the tire: Once the jack is in place, remove the tire. Be cautious as the jack may shift during the installation of the spare tire. Place the removed tire under the vehicle to minimize the risk of accidents. Tighten the wheel bolts: First, screw in one bolt, then proceed to tighten all the bolts. Typically, the same number of turns should be applied to each bolt to ensure even distribution of force. Remove the jack: Slowly release the jack and remove it, allowing the car to settle steadily on the ground.
15
1
Share

How many kilometers can a Chery engine run?

Currently, domestically designed and manufactured engines in China, with proper maintenance and normal driving, can ensure that the vast majority of engines will last a long time. Engine Quality: In terms of the engine alone, it is a relatively low-tech component compared to systems like four-wheel drive, transmissions, and tuning. Producing an engine that doesn't have problems is not particularly difficult. Engine Issues: The quality can be made very good; where it often falls short is in the technical performance of the engine, such as fuel consumption, power, noise, balance, etc.—parameters that enhance the engine's value.
10
5
Share

What are the reasons why the Mercedes S500 ETC cannot be used?

The reasons why the Mercedes S500 ETC cannot be used include excessive speed, the card LED displaying no OBU, OBU device issues, or the ETC used not being the one registered for the vehicle. Excessive speed: Normally, ETC regulations stipulate that the vehicle's speed when passing through the detection system must not exceed 20 kilometers per hour. If the speed is too high, the system cannot properly scan the ETC card. Card LED displaying no OBU: This situation usually occurs when the card is not inserted properly. Reinserting the card correctly can resolve the issue. OBU device issues: This is typically due to the OBU being out of power or improperly positioned. Adjust the position promptly and recharge the device. The ETC used is not the one registered for the vehicle: Since ETC uses a one-vehicle-one-card recording method, using someone else's ETC that does not match the license plate number will result in failure to pass the toll station. In such cases, the manual lane can be used. The ETC installation process is as follows: Upon receiving the device, first check if the ETC card and electronic tag (OBU) are damaged. Press the anti-tamper button on the back of the OBU; a red light will briefly turn on, and the OLED screen will display "Tag Invalid, Insert Card," indicating the device is functioning normally. Clean the front windshield, ensuring the surface is smooth, clean, and dry. Then, peel off the adhesive backing of the OBU and stick it to the installation position. Press firmly for 2-3 minutes to remove any air bubbles. Insert the ETC card with the front facing the driver and the back facing the windshield, ensuring the chip is inserted into the OBU device.
17
5
Share

Which BMW X5 model comes with the LCD smart key?

20 model year BMW X5 comes with the LCD smart key, while the 21 model year BMW X5 has discontinued the LCD key. Remote engine start: In summer, it allows for parking ventilation to cool down the car in advance. In winter, vehicles equipped with a preheating device can also be preheated to warm up beforehand. Check safety information: Such as whether the doors, windows, sunroof, and trunk are closed. Check vehicle information: Such as fuel consumption, tire pressure, remaining range, and other details. Emergency vehicle start: For vehicles equipped with the LCD key, the factory provides an additional mechanical key. This mechanical key can be used to open the door, step on the brake, press the LCD key against the key icon on the steering column, and then press the one-touch start button within 10 seconds.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.