How to adjust the car alarm sound of Wuling Hongguang S?

2 Answers
StAiden
07/28/25 8:16pm
Method to adjust the car alarm sound of Wuling Hongguang S: The adjustment for the car alarm sound is located at the anti-theft device position under the steering wheel, where there is a matchbox-sized vibration sensor. Use a small cross screwdriver to rotate it for adjustment. Generally, after locking the car, there will be continuous noise at the front of the vehicle, but don't worry, it will automatically stop within a few minutes—that's the sound of the fan rotating. The Wuling Hongguang S is a model launched by SAIC-GM-Wuling based on the Wuling Hongguang series, positioned between commercial vehicles and passenger cars. In terms of body dimensions, the Wuling Hongguang S measures 4400mm in length, 1680mm in width, and 1770mm in height, with a wheelbase of 2720mm. Exterior-wise, the upper grille on the front face of the Wuling Hongguang S is traversed by a single wide horizontal bar, accompanied by chrome trim. The honeycomb grille, along with two silver protective plates at the front and rear bottom, adds a touch of ruggedness to the Wuling Hongguang S while also enhancing the overall visual quality of the vehicle.
Was this review help?
2
3
Share
Gabrielle
08/12/25 1:05am
For adjusting the alarm sound of the Wuling Hongguang S, here's how I did it: The remote key is the primary method. After locking the car, simultaneously press and hold the lock and unlock buttons for about 10 seconds. Release the buttons upon hearing a beep, and the alarm sound mode will switch once. Some model years also support volume adjustment. After starting the engine, access the settings option through the dashboard menu, find the sound or security section, and customize it. There are usually three levels to choose from: high, low, or mute mode. Make sure the key battery is fully charged during operation, or it may malfunction. Setting it too low reduces anti-theft effectiveness, while setting it too high may disturb others. After a few tries, I found a moderate setting. At night, I switch to mute mode to avoid disturbing the neighbors, which is quite practical. Personally, I recommend checking the user manual first to confirm the specific steps to avoid mistakes. Overall, it's simple and convenient, enhancing the daily driving experience.
Was this review help?
17
5
Share
Expand All
More Forum Discussions

What are the required procedures and documents for reissuing a driver's license?

The required procedures and documents for reissuing a driver's license include: 1. Motor vehicle driver's license application form; 2. ID card and photocopy of the applicant; 3. Digital photo of the driver; 4. A written statement of loss for the driver's license. The procedure for renewing an expired driver's license is: According to road traffic safety laws and regulations, the validity period of a motor vehicle driver's license is 6 years, and the driver should apply for renewal within 90 days before the expiration date. Notes for renewing an expired driver's license: 1. The applicant must truthfully submit the required materials to the vehicle management office, declare the required items truthfully, and be responsible for the authenticity of the substantive content of the application materials; 2. The applicant must meet the application conditions stipulated in the regulations for the application and use of motor vehicle driver's licenses.
6
5
Share

What is the difference between 1.4L and 1.5L?

The difference between 1.4L and 1.5L is the displacement: 1.4L has a displacement of 1.4 liters, while 1.5L has a displacement of 1.5 liters. Both 1.4L and 1.5L are naturally aspirated engines. The engine consists of: 1. Valve train; 2. Crankshaft and connecting rod mechanism; 3. Ignition system; 4. Cooling system; 5. Lubrication system; 6. Fuel supply system. The function of the engine is to convert the heat energy of gasoline or diesel into mechanical energy by burning the expanding gas in a sealed cylinder to push the piston. Engine maintenance items include: 1. Regularly change the engine oil and oil filter; 2. Keep the crankcase well ventilated; 3. Regularly clean the crankcase; 4. Regularly clean the fuel system; 5. Regularly maintain the radiator; 6. Maintain and clean the fuel system.
13
5
Share

What is the removal method for the three rear spark plugs of the Buick GL8?

The removal method for the three rear spark plugs of the Buick GL8 is as follows: 1. Use a screwdriver to remove the engine cover; 2. Clean the dust and oil stains from the high-voltage wire terminals; 3. Use a socket wrench to loosen the fixing screws of the high-voltage wire terminals; 4. Use a socket wrench to loosen the spark plugs; 5. Insert the soft tube from the high-voltage wire terminal into the combustion chamber; 6. Pull out and remove the spark plugs. Taking the 2021 Buick GL8 as an example, its body dimensions are: length 5238mm, width 1878mm, height 1776mm, wheelbase 3088mm, fuel tank capacity 66L, and trunk capacity 475L. The 2021 Buick GL8 is equipped with a 2.0T turbocharged engine, with a maximum horsepower of 237PS, maximum torque of 350Nm, maximum power of 174kW, and is paired with a 9-speed automatic transmission.
5
1
Share

What are the reasons for reduced engine power in Buick vehicles?

Buick engine power reduction can be attributed to: 1. Poor fuel quality and fuel line blockages; 2. Engine overheating. Taking the 2021 Buick GL8 as an example, its body dimensions are: length 5238mm, width 1878mm, height 1776mm, wheelbase 3088mm, fuel tank capacity 66L, and trunk capacity 475L. The 2021 Buick GL8 is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 237PS, maximum torque of 350Nm, and maximum power of 174kW, paired with a 9-speed automatic transmission.
12
4
Share

What happens if you use 92 octane gasoline in a Volkswagen CC?

According to the official vehicle manual recommendation, the Volkswagen CC should use 95 octane gasoline. In addition to checking the suitable gasoline grade in the vehicle manual, you can also find it marked on the fuel tank cap of the Volkswagen CC. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. However, with the application of new technologies, the compression ratio alone cannot determine the appropriate gasoline grade. High compression ratio engines can still be tuned to use lower octane gasoline because factors other than compression ratio, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If you occasionally use the wrong gasoline grade in a Volkswagen CC, simply switch back to the correct grade after consumption. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using higher octane gasoline will not cause damage, but the increase in octane number may alter the fuel's ignition point, leading to delayed combustion in the engine. This results in reduced engine power and thermal efficiency, with the practical effect being poorer performance. For vehicles recommended to use higher octane gasoline, using lower octane gasoline can cause engine knocking. Because the octane number is significantly lower, the reduced ignition point may cause premature ignition during the compression stroke. If combustion occurs before the spark plug ignites, resistance will arise during the upward stroke. This resistance makes the engine run very unstably. If the knocking is mild, it may only increase noise without obvious engine damage. However, noticeable knocking indicates severe engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in severe cases, cylinder scoring.
16
4
Share

What is the method to start a Bestune X40 when the key fob battery is dead?

The method to start a Bestune X40 when the key fob battery is dead is: 1. Remove the separate key equipped on the remote key fob; 2. Insert the key into the hidden keyhole under the steering wheel to start the vehicle. Taking the 2019 Bestune X40 as an example, its body structure is a 5-door, 5-seat SUV with body dimensions of: length 4310mm, width 1780mm, height 1680mm, wheelbase of 2600mm, fuel tank capacity of 50L, and curb weight of 1325kg. The 2019 Bestune X40 features a MacPherson strut front suspension and a torsion beam rear suspension, powered by a 1.6L naturally aspirated engine with a maximum horsepower of 114PS, maximum power of 84kW, and maximum torque of 115Nm.
4
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.