How to Adjust the Brightness of the Borui GE Instrument Panel?

What does ecoboost mean?

EcoBoost is a series of turbocharged and direct fuel-injected 6-cylinder and 4-cylinder gasoline engines produced by Ford Motor Company. Building upon traditional gasoline engines, EcoBoost engines incorporate three key technological advantages: direct fuel injection, turbocharging, and twin independent variable camshaft timing (Ti-VCT) systems. These enhancements not only ensure robust power output but also improve fuel economy by up to 20% and reduce CO2 emissions by 15%. The primary advantage of Ford's EcoBoost engines lies in their ability to effectively reduce engine displacement, replacing larger traditional naturally aspirated engines with smaller ones without sacrificing any power output. Generally, turbochargers can increase torque by 50%, allowing for strong power performance while significantly reducing engine displacement, optimizing fuel consumption and exhaust emissions. The principle of ECO: ECO primarily involves comprehensive judgment and analysis of factors affecting fuel consumption during vehicle movement, such as automatic transmission gear position, engine speed, vehicle speed, braking, and transmission oil temperature. The ECU control unit calculates the optimal fuel quantity to supply the engine for operation, effectively reducing fuel consumption compared to normal driving modes. Simply put, it controls engine speed with appropriate gear selection to minimize unnecessary fuel consumption.

4

0

Share

What does excessively high temperature difference between EGP inlet and outlet mean?

An excessively high temperature difference between EGP inlet and outlet generally refers to an excessive difference between atmospheric temperature and exhaust gas outlet temperature. Below is an introduction to EGP knowledge: Introduction: "EGP" refers to the diesel electronically controlled common rail National IV exhaust treatment component, commonly known as the muffler with catalytic converter. The exhaust treatment unit is equipped with 2 catalytic converter temperature sensors and 1 NOX sensor. The two temperature sensors are located at the inlet and outlet of the catalytic converter, referred to as inlet and outlet temperature sensors respectively. Function: Its main purpose is to detect the temperature of exhaust gases from the engine. When the detected exhaust temperature exceeds 200°C, the engine's electronic control unit receives this signal and sends corresponding execution commands to the metering injection pump to control the nozzle to inject a certain amount of urea solution into the exhaust pipe.

7

2

Share

What is the difference between escape1 and escape2?

The differences between escape1 and escape2 are as follows: In terms of transmission components: escape2 uses an 8-speed M310 groupset with an aftermarket chainring. escape1 uses a full Shimano groupset with M370 front derailleur, M430 rear derailleur, M391 chainring, and M355 hydraulic disc brakes, which is one level higher in configuration than escape2. In terms of cost-effectiveness: escape2 offers better value for money. For beginners, escape2 is recommended. As you gain more riding experience and knowledge, you can upgrade the bike according to your actual needs.

13

3

Share

What type of oil is used in the EA888 engine?

The EA888 engine uses two types of oil: 5W40 and 5W30. The 5W40 has a lower viscosity and offers better high-temperature protection. For later maintenance and oil changes, you can choose brands like Castrol or Mobil. The official manual recommends 5W-40 and 5W30. Oil viscosity changes with temperature, so it's important to pay attention to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity—5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, ensuring smoother cold starts for the car. The second number represents the oil's kinematic viscosity at 100°C. A higher number indicates better viscosity retention at high temperatures, meaning better lubrication performance under high-temperature conditions. The method for changing the oil in the EA888 is as follows: Wait for the engine temperature to cool down, allowing the oil to drain back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine and let it run for 30 seconds to drain any remaining oil from the main oil passages. Use a specialized wrench to remove the oil filter. Apply oil to the seal of the new oil filter and hand-tighten it clockwise. Add the new oil through the engine valve cover filler port, typically filling about three-quarters of the oil container. Start the engine and let it run for 5 minutes, checking for leaks around the oil drain plug and oil filter. If leaks are found, perform necessary repairs. After stopping the engine, pull out the dipstick to check that the oil level is within the standard range.

15

3

Share

What are the possible causes of EPB failure?

There may be an issue with the electronic parking brake. Below is relevant information: Introduction: EPB stands for Electrical Park Brake, which is the electronic parking brake system. The electronic parking brake system relies on electronic control and uses a longitudinal acceleration sensor to calculate the slope. When an EPB failure occurs, you can press the foot brake down while also pressing the handbrake down, hold for about 20 seconds, and then lift the handbrake up to restore normal operation. Advantages of EPB: It replaces the traditional mechanical lever and tire cables, providing better assistance to the driver. The electronic parking brake button, which replaces the traditional lever handbrake, is safer than the traditional lever handbrake. The braking effect is not affected by the driver's force, turning the traditional lever handbrake into an easily accessible button.

1

3

Share

What does ESC failure mean?

ESC failure indicates that the vehicle's electronic stability control system is currently not functioning. Here is some relevant information about ESC: Function: The primary role of ESC is to make the car more stable and safe when changing lanes or turning. Under normal driving conditions, the ESC system does not operate. When the ignition switch is turned on, ESC is activated, the warning light illuminates, and the ESC off indicator light comes on for about 4 seconds before turning off. Composition: The system consists of three main parts: sensors, an electronic control unit (ECU), and actuators. The electronic control unit monitors the vehicle's operating status and intervenes in the engine and braking system to control the vehicle.

16

3

Share

How to Adjust the Brightness of the Borui GE Instrument Panel?

What does ecoboost mean?

What does excessively high temperature difference between EGP inlet and outlet mean?

What is the difference between escape1 and escape2?

What type of oil is used in the EA888 engine?

What are the possible causes of EPB failure?

What does ESC failure mean?

Who gets the demerit points if a mortgaged car without transfer commits a traffic violation?

What is eco?

What is the fault code for EECU message?

What is an EFI fuse?