How to Adjust the Audio System in the LaCrosse?

What is the motor power of the BMW i3?

The BMW i3's motor has a maximum power of 125kW and a maximum torque of 250Nm. This car's motor can be classified as a permanent magnet synchronous motor, which not only ensures the motor's working efficiency at high speeds but also guarantees smoother torque output. The BMW i3 is a pure electric vehicle under the BMW brand, belonging to the small hatchback category. Its body dimensions are 4020mm in length, 1775mm in width, and 1600mm in height, with a wheelbase of 2570mm. In terms of suspension, it features a MacPherson strut independent front suspension and a multi-link independent rear suspension.

11

0

Share

What are the common issues with the 2012 used Audi A6L?

The common issues with the 2012 used Audi A6L include excessive car noise, jerking during reversing and starting, and unsteady gear shifting. Taking the Audi A6L 2012 TFSI manual basic model as an example, its dimensions are 5015 mm in length, 1874 mm in width, and 1455 mm in height, with a wheelbase of 3012 mm. It has a fuel tank capacity of 75 liters and a body structure of a 4-door, 5-seat sedan, with front-wheel drive. In terms of power, it is equipped with a 2.0T turbocharged engine, delivering a maximum power of 132 kW and a maximum torque of 320 Nm, paired with a 6-speed manual transmission.

6

5

Share

What are the reasons for low efficiency of the three-way catalytic converter?

The aging or clogging of the three-way catalytic converter leads to a decline in performance. Specific details are as follows: 1. Reasons for low efficiency: If the three-way catalytic converter exhibits low efficiency, this is generally due to clogging in the three-way catalytic system. When clogged, the vehicle's exhaust flow becomes obstructed, affecting power and increasing fuel consumption. In such cases, it is necessary to determine the severity of the clogging in the three-way catalytic system. 2. Degree of clogging: If the clogging is mild to moderate, it can be cleaned and repaired using specialized equipment designed for oxidizing the three-way catalytic converter. However, if the clogging is severe, immediate replacement of the three-way catalytic converter is required.

13

5

Share

Where is the cabin light switch located on the roof?

The cabin light switch on the roof is located next to the light. There is a button with three modes: ON (constant on mode), DOOR (light on when door opens and off when closed), and OFF (off mode). It is usually set to DOOR mode. The light automatically turns on when the door is opened and off when the door is closed. If the button is set to ON, the light will remain constantly on and needs to be manually turned off. If the cabin light cannot be turned off, it may be because the door is not properly closed. Check the door status. If the light is malfunctioning and no issues are found, it is recommended to visit a professional repair shop or 4S store for inspection.

15

3

Share

Why does the car fail to start when hot but starts fine when cold?

Car failing to start when hot but starting fine when cold is usually caused by excessive engine carbon deposits. It is recommended that the driver check whether the car's spark plugs need replacement and whether the throttle needs cleaning. The throttle is a controllable valve that regulates air intake into the engine. After entering the intake pipe, the air mixes with gasoline to form a combustible mixture, which then burns to perform work. The throttle is connected to the air filter at the top and the engine block at the bottom, and is often referred to as the throat of the car engine. The spark plug is a crucial component of the gasoline engine's ignition system. It introduces high-voltage electricity into the combustion chamber and creates a spark by jumping the electrode gap, thereby igniting the combustible mixture in the cylinder.

2

5

Share

What Causes Incomplete Brake Caliper Retraction?

Incomplete brake caliper retraction may be caused by the piston not returning or the guide sliding pin not retracting properly. Below is a detailed explanation of the reasons for incomplete brake caliper retraction: 1. Brake caliper piston not returning: Prolonged failure to replace brake fluid and imprecise manufacturing of the brake caliper can lead to rust buildup inside the piston over time. To address this, the brake caliper can be disassembled to clean rust and debris from the piston and piston cylinder, followed by replacing the brake fluid with new fluid. 2. Brake caliper guide sliding pin not retracting: If the sliding pin becomes rusted and stuck, the caliper cannot retract properly, leading to issues such as brake lock-up.

14

3

Share

How to Adjust the Audio System in the LaCrosse?

What is the motor power of the BMW i3?

What are the common issues with the 2012 used Audi A6L?

What are the reasons for low efficiency of the three-way catalytic converter?

Where is the cabin light switch located on the roof?

Why does the car fail to start when hot but starts fine when cold?

What Causes Incomplete Brake Caliper Retraction?

What are the symptoms of a car without a catalytic converter?

What does the wrench symbol mean when it appears on a new car?

Under what circumstances will the Lavida's anti-theft alarm sound?

What does the yellow exclamation mark in the car mean?