How to Adjust the Angle of the Wiper Linkage Rod?

1 Answers
Kayden
07/30/25 7:17am
For the majority of vehicles currently on the market, the wiper switch is located on the right-hand stalk behind the steering wheel, typically in the form of a lever. For example, models like the GAC Fiat Viaggio and Mercedes-Benz have their wiper switches positioned differently from other vehicles, being located on the left-hand stalk. In some models, the automatic intermittent wiper setting can be adjusted to vary the sweeping frequency, allowing the wipers to operate at different speeds depending on the vehicle's speed.
Was this review help?
6
3
Share
More Forum Discussions

What is the ground clearance of the Volkswagen Tiguan?

The ground clearance of the Volkswagen Tiguan is 180mm. Ground clearance refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the car is fully loaded and stationary. It is used to indicate the vehicle's ability to pass over obstacles such as rocks and stumps without collision. The Volkswagen Tiguan is equipped with a MacPherson strut independent front suspension and a multi-link independent rear suspension. The Tiguan is a compact SUV under the Volkswagen brand, with dimensions of 4506mm in length, 1809mm in width, and 1685mm in height, and a wheelbase of 2684mm. The Tiguan is powered by two engines: a 1.4-liter turbocharged engine and a 1.8-liter turbocharged engine.
18
0
Share

What do the letters E and F on the fuel gauge mean?

The letter E on the fuel gauge stands for empty, using the first letter of the word 'empty', while the opposite letter F stands for full, derived from the word 'full'. Here is some relevant information: 1. When the car's fuel tank is full, the fuel gauge needle will point towards the letter F. When the fuel gauge needle points to E, a gas station symbol will light up on the dashboard, indicating that the fuel in the tank is only enough to drive for a dozen or so kilometers, and you should go to a gas station to refuel as soon as possible. 2. The principle of the fuel gauge display is actually like having a float in the fuel tank. The float sends different signals at different positions, and the instrument panel receives these different signals to display the current fuel level. You may have noticed that when the vehicle is on bumpy roads or going up and down slopes, the fuel gauge needle may swing, and the fuel tank warning light may come on.
7
0
Share

Where is the Focus Mondeo's Cabin Air Filter Located?

Ford Mondeo is a mid-size sedan sold by Ford Motor Company in multiple markets worldwide. Below is an introduction to the installation locations of the cabin air filter for different models of the Ford Mondeo: 1. In older models of the Ford Mondeo, the cabin air filter is located to the right of the accelerator pedal. To replace the cabin air filter, the accelerator pedal must first be removed to facilitate the replacement process. 2. Newer models of the Mondeo have replaced this setup, now placing the cabin air filter inside the glove box, which is currently the mainstream installation location for cabin air filters in vehicles.
19
3
Share

How to Deal with Smoke from Truck Brakes?

Truck brake smoke usually indicates that the brake pads are overheated. In this case, you should pull the vehicle over to the side of the road and allow the brake pads to cool naturally. If the smoke is caused by other issues, it is necessary to visit the nearest repair shop for professional inspection and maintenance to prevent potential safety hazards. The specific reasons are as follows: 1. The handbrake was not released during driving. If the handbrake is not released while driving, the friction can cause the brake pads to smoke. This situation causes significant wear on the brake pads, and in severe cases, the brake pads may be completely ruined. 2. Prolonged braking. Continuous braking during long downhill sections can also cause white smoke due to overheating of the brake pads. It is important to note that when driving on long downhill sections, the engine's traction should be used to assist braking to prevent the brake pads from overheating, which could reduce braking efficiency or even cause brake system failure, leading to safety hazards.
12
3
Share

What to Do If the Car Stalls After Driving into Water?

The handling method for a car stalling after driving into water is: 1. Do not attempt to restart the engine; push the car to a location where it does not obstruct traffic; 2. Close all doors and windows and wait for rescue. The impacts of driving through water include: 1. The engine may experience insufficient power and shaking issues; the high-voltage distribution system may become damp or short-circuited due to water ingress; water may enter the exhaust pipe. 2. Residual water can prevent the brake discs and brake pads from fully engaging, causing the car to lose braking power; debris can easily adhere to the gaps in the chassis, leading to rust. 3. Water vapor may form inside the headlights, affecting the light transmission; the wiring harness and circuit interfaces in the engine compartment may get wet, causing short circuits.
7
3
Share

What is the tutorial for replacing the battery in an old Mercedes-Benz G key?

The tutorial for replacing the battery in an old Mercedes-Benz G-Class key is as follows: 1. Before replacement, it's best to first understand the battery model of your car key, which is usually written in the vehicle's user manual. Then select a new key battery according to the specified model. 2. From the tail of the key, push up the marked switch, and the hidden mechanical key will pop out slightly. Then you can take out the mechanical key. 3. Still at the tail of the key, use the just removed mechanical key to press against the marked position. With a slight force, the key shell can be opened. 4. After removing the key shell, you can see that the battery position is relatively deep. Use any object to slide into the gap on both sides and gently pry to remove the old battery. 5. After installing the new battery, make sure the positive and negative poles are not reversed. Then proceed with the installation steps: first insert the top of the shell, then press firmly on the other end to complete the battery replacement. Finally, don't forget to put the mechanical key back in place.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.