How to adjust the ambient lighting in A6?

Is the Ground Clearance of Jade Higher Than That of Civic?

Under no-load conditions, the ground clearance of Jade is 195mm. In contrast, the Civic has a ground clearance of approximately 141mm under the same conditions. Therefore, the ground clearance of Jade is higher than that of Civic. Below are the introductions of Jade and Civic: 1. The Jade 1.5T model is equipped with the Honda SENSING safety system, which integrates ACC active cruise control system, LKAS lane keeping assist system, RDM lane departure mitigation system, TSR traffic sign recognition system, LWC blind spot display system, and RWC rear wide-angle camera system. 2. The Civic is equipped with 1.0T and 1.5T engines, as well as manual and CVT transmissions. It features a large number of black elements, including the black front grille, side skirts, the newly added small spoiler, and black glossy alloy wheels.

11

4

Share

What are the effects of low tire pressure in sedans?

The effects of low tire pressure in sedans are as follows: 1. Low tire pressure can lead to increased fuel consumption, heavier steering, and a tendency for the vehicle to drift. It can also cause damage and abnormal wear to the tire bead area, reduced tire strength, and may result in a tire blowout during high-speed driving; 2. Insufficient tire pressure increases the movement of various parts of the tire, leading to excessive rolling that causes abnormal heat buildup. This reduces the functionality of the cords and rubber, potentially causing delamination or cord breakage, and excessive friction between the tire and the rim, resulting in damage and abnormal wear to the tire bead area; 3. The friction between the tire and the ground increases exponentially, leading to a rapid rise in tire temperature, softening of the tire, and a sharp decrease in strength. High-speed driving under these conditions can also cause a tire blowout.

14

0

Share

Where is the oil filter element located on the Kia K3?

The oil filter element of the Kia K3 is located inside the fuel tank and assembled together with the fuel pump. To access it, you need to open the fuel tank cap, disassemble the fuel pump assembly, replace the fuel filter, and then reassemble it with the fuel pump. Alternatively, you can replace the entire assembly including the fuel pump. The oil filter element, also known as the oil filter, functions to remove debris, gum, and moisture from the engine oil, delivering clean oil to various lubrication points. More details are as follows: 1. Most vehicles are equipped with spin-on oil filter elements, which are disposable and not cleanable. Therefore, it is recommended to replace the oil filter element when changing the engine oil. Failing to do so may affect the quality of the lubricating oil. Generally, it is advisable to replace the oil filter every 5,000 kilometers. 2. To reduce friction resistance between moving parts in the engine and minimize component wear, engine oil is continuously delivered to the friction surfaces of moving parts, forming a lubricating oil film for lubrication. 3. There are many types of oil filter elements, including those for screw-type air compressors, as well as models like WK962/7 and WK940/20. Different vehicle models require different oil filter elements, and even a slight mismatch can prevent proper installation.

19

4

Share

How to solve the SVS fault in Jiangling vehicles?

The solution for the SVS light turning on is to start the engine first. If it fails to start, the fuel pump might be malfunctioning, preventing the normal supply of fuel to the engine. However, the fault can also affect the normal use of the vehicle, such as causing body shaking and increased fuel consumption. In such cases, it is advisable to take the vehicle to a repair shop for a comprehensive inspection.

10

2

Share

What are the reasons for a car constantly shaking?

Reasons for a car constantly shaking: 1. Severe engine carbon buildup: The most common cause of car shaking is a dirty throttle body or excessive carbon deposits in the fuel injectors. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts, making it difficult to start. In this situation, the car will only start easily once the carbon deposits have absorbed enough gasoline to become saturated. After starting, the gasoline adsorbed on the carbon deposits is sucked into the combustion chamber by the engine's vacuum, making the air-fuel mixture too rich. This fluctuation between lean and rich mixtures causes the engine to shake at idle after a cold start. The lower the temperature, the more fuel is needed for a cold start, and the presence of carbon deposits significantly affects the success of the cold start. 2. Ignition system issues: Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or weak sparking from the spark plugs can also cause severe shaking during cold starts. 3. Unstable fuel pressure: If you have already cleaned the engine carbon deposits, throttle body, replaced gaskets, and spark plugs but still notice shaking at idle, it is recommended to visit a 4S shop to check the fuel supply pressure and the intake pressure sensor. Abnormal fuel pump pressure or incorrect readings and poor performance of the intake pressure sensor can both cause the car to shake. 4. Aging engine components: Car shaking can also be related to the aging of engine mounts (also known as engine mounts or cushions). Engine mounts act as the engine's shock absorption system, absorbing minor vibrations during operation. If the engine mounts are faulty, these vibrations will be transmitted to the steering wheel and the cabin, causing shaking at idle.

14

5

Share

How to align the timing chain on the Jianghuai Refine M3?

Check through the spark plug hole and manually rotate the crankshaft pulley fixing bolt with a wrench or socket. Insert the No. 1 special tool tightly into the timing groove of the intake and exhaust camshafts from the rear plane area of the cylinder head.

8

2

Share

How to adjust the ambient lighting in A6?

Is the Ground Clearance of Jade Higher Than That of Civic?

What are the effects of low tire pressure in sedans?

Where is the oil filter element located on the Kia K3?

How to solve the SVS fault in Jiangling vehicles?

What are the reasons for a car constantly shaking?

How to align the timing chain on the Jianghuai Refine M3?

How to Handle Vehicle Insurance?

Which brand is Borgward?

How to Solve the Squeaking Noise of Windshield Wipers?

Which Button to Press for Defogging on Rainy Days?