How to Adjust the Air Conditioning to Cold Air Mode in the Car?

2 Answers
EdenLee
07/29/25 4:45am
To set the air conditioning to cold air mode, simply turn on the air conditioning switch, press the A/C button, and then rotate the temperature control dial to the blue position. For automatic air conditioning, just press the auto button and the A/C button to light them up. The reasons why the car air conditioning is not cooling properly are as follows: 1. Refrigerant leakage: Insufficient pressure in the system leads to poor cooling performance. 2. Air duct blockage: Due to prolonged lack of cleaning, there is a lot of dust in the air conditioning ducts, requiring cleaning. 3. Reduced cooling efficiency of the condenser: This could be due to aging equipment or dust and debris on the condenser surface affecting heat exchange. 4. Improper use of the air conditioning: If the air conditioning is used with the external circulation on, it will inevitably bring hot air from outside into the car, reducing the cooling efficiency.
Was this review help?
1
4
Share
DelLola
08/12/25 8:25am
When I first started learning to drive, I didn't know how to adjust the cold air either, but now I've figured it out: First, start the engine, then turn the temperature control knob to the lowest position (usually the blue icon area), press the AC button to turn on the compressor for cold air, and then use the fan speed button or knob to control the airflow. During hot summer days, I avoid blowing air directly at my face to prevent catching a cold. At the same time, turning on the recirculation mode can cool the car faster, but don't keep it on all the time—switch to fresh air mode every half hour for ventilation. Regularly checking the cabin air filter and refrigerant ensures good cooling performance. This setup is simple and safe, making driving much more comfortable.
Was this review help?
3
0
Share
Expand All
More Forum Discussions

How Long Can a 2008 Car Be Driven?

A 2008 car can be driven as long as it meets the following conditions: first, it must pass the annual inspection; second, there are no local driving restrictions in place; third, the mileage does not exceed 600,000 kilometers. Here are the relevant details: 1. Whether a car is scrapped is not determined by its age but by its mileage. A car must be forcibly scrapped once it reaches 600,000 kilometers. For specifics, refer to Articles 5 and 7 of the "Regulations on the Compulsory Scrapping Standards for Motor Vehicles." 2. Regarding driving restrictions, for example, a 2008 car typically meets the National III emission standard. If a local policy prohibits vehicles with National III emissions from being driven on the road, then the car cannot be used. Major cities like Beijing, Shanghai, Guangzhou, and Shenzhen have already implemented corresponding driving restrictions. 3. Additionally, cars older than 15 years must undergo inspections every six months, meaning two annual inspections per year. If the car fails even one inspection, it cannot be driven. For specifics, refer to Article 16 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China."
6
2
Share

How to Replace the Interior Door Handle?

First, install the T-shaped connector of the cable into the mounting hole located on the opposite side of the interior handle's pivot shaft. Then, press the cable clip into the positioning structure of the handle base. By pulling the interior handle to rotate around the pivot shaft, the cable is pulled, and the door will open. Proceed with the replacement.
6
0
Share

What to Do When the Car is Too Close to the Left Side?

Straighten back a little, then drive forward to the right a bit, and straighten back again. Repeating this two or three times should do the trick. Depending on the size of the space, if you realize it's not suitable right after entering, you can try reversing out the same way and then re-entering. If the car isn't too close, you can make slight adjustments. If it's extremely close, you'll need to be very careful and move out bit by bit.
15
4
Share

How to adjust the low beam height of the 2021 Malibu XL?

Enter the driver's cabin and you can see the headlight height adjustment knob on the left side of the dashboard. Adjust according to the headlight height levels marked on the knob. When the highest light position is needed, turn the knob to the "0" position. To lower the light by one level, rotate the knob to the "1" position. The "2" position provides a relatively low light height. When the lowest light position is required, turn the knob to the "3" position.
6
2
Share

How to Deal with Speeding?

If the speed exceeds the speed limit by less than 10%, a warning will be issued. On roads with a speed limit below 50 km/h, if the speed exceeds the speed limit by 10% or more but less than 20%, a fine will be imposed. If the speed exceeds the speed limit by 20% or more but less than 50%, by 50% or more but less than 70%, or by 70% or more, a fine will be imposed. On roads with a speed limit between 50 km/h and 80 km/h, if the speed exceeds the speed limit by 10% or more but less than 20%, a fine will be imposed. If the speed exceeds the speed limit by 20% or more but less than 50%, by 50% or more but less than 70%, or by 70% or more, a fine will be imposed.
19
3
Share

How to Turn on the High Beam on a Mercedes-Benz?

There are two methods to turn on the high beam: The first method is to pull the left-hand stalk toward the driver to activate the high beam. Releasing the stalk will automatically reset it and turn off the high beam. The second method is to push the stalk away from the driver, which will keep the high beam on continuously. Below is an introduction to the high beam: 1. Vehicle lights adjust the intensity of light based on the distance of the filament: The high beam is focused at its focal point, emitting light that travels parallel, is more concentrated, and brighter, allowing it to illuminate distant and high objects. The low beam is positioned beyond its focal point (between 1x and 2x the focal length), emitting light in a divergent pattern to illuminate a larger area of nearby objects. 2. The difference between high beam and low beam: Both are used for nighttime illumination, but the high beam has a higher angle and longer range, while the low beam has a lower angle and shorter range. 3. It is generally advisable not to use the high beam when driving in the city: Urban areas typically have good lighting conditions. The high beam's elevated angle can easily dazzle oncoming drivers and pedestrians, impairing their vision and posing safety risks, as well as being considered impolite driving behavior. 4. Alternately switching the high beam on and off at night can serve as a substitute for the horn to alert nearby pedestrians and vehicles: This helps avoid excessive noise. On highways or in rural areas without streetlights, using the high beam can expand the field of vision. However, when encountering oncoming traffic, it is recommended to switch to the low beam for safety and courtesy considerations.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.