···
Log in / Register

How to Activate the Cruise Control on the Hongqi H5?

1 Answers
SimonRose
08/26/25 6:01am
The method to activate the cruise control on the Hongqi H5 is as follows: First, turn on the system by pressing the on/off button or pushing the lever. The cruise control indicator light on the dashboard will illuminate. Then, press the accelerator to reach the desired speed and press the SET button. At this point, you can release the accelerator pedal, and the speed will be maintained at the current level. The Hongqi H5 is equipped with a 1.5-liter turbocharged engine paired with a 7-speed wet dual-clutch transmission, delivering a maximum power of 124 kW and a maximum torque of 258 Nm. In terms of exterior design, the Hongqi H5 features an inverted trapezoidal front grille connected to the headlights, with vertical chrome trim strips embedded inside. The vehicle dimensions are 4945 mm in length, 1845 mm in width, and 1470 mm in height, with a wheelbase of 2875 mm.
Was this review help?
19
1
Share
More Forum Discussions

How to Open the Fuel Tank Cap of the Ford Kuga?

The method to open the fuel tank cap of the Ford Kuga is: 1. Locate the fuel tank cap release switch near the driver's seat, pull the switch once, and the fuel tank cap will pop open; 2. Turn the inner fuel tank cap counterclockwise to open it. Taking the 2019 Ford Kuga as an example, it belongs to the compact SUV category, with body dimensions of: length 4525mm, width 1838mm, height 1685mm, wheelbase of 2690mm, fuel tank capacity of 60 liters, and curb weight of 1592kg. The 2019 Ford Kuga is equipped with a 1.5T turbocharged engine, with a maximum horsepower of 182PS, maximum power of 134kW, maximum torque of 245Nm, and is paired with a 6-speed automatic transmission.
12
5
Share

What is the starting sequence for a manual transmission car?

Manual transmission car starting steps are as follows: 1. Before pushing the car, turn the key to the ON position to power up the vehicle, eliminating the need for manual key ignition. 2. Then depress the clutch and shift into second or third gear. 3. When the pushing speed reaches about 10km/h, release the clutch while simultaneously applying some throttle assistance. 4. When the engine shows signs of starting accompanied by operational sounds, it can generally be started successfully. At this point, quickly depress the clutch, shift to neutral, and control the throttle properly to complete the startup. Extension: If attempting to start while in gear without depressing the clutch, it will cause the car to lurch forward, potentially leading to a rear-end collision. Additionally, the engine operating under heavy load may stall, causing abnormal wear. When in neutral, avoid rocking the gearshift lever back and forth as this accelerates wear on the shift fork, eventually leading to difficult gear shifting over time.
20
2
Share

Which Year's Vehicles Are Considered China III Standards?

Generally speaking, vehicles produced between 2007 and 2010 comply with China III emission standards. Below are specific methods to check which emission standard a vehicle falls under: 1. Check the vehicle's environmental protection label - the standard is clearly marked on the back. 2. Query through the website of the Motor Vehicle Exhaust Pollution Supervision and Management Center. 3. Bring the original or copy of the vehicle registration certificate to the vehicle management office for inquiry. 4. For new vehicles, check the factory certificate of conformity (usually kept at the vehicle management office). It's recommended to make a copy when purchasing a car. 5. Make a rough estimation based on the vehicle's registration year: Most vehicles registered after 2008 are China IV; 2007 registered vehicles could be either China III or IV; vehicles registered before 2007 are mostly China III or II; those registered before 2005 are basically China II standards.
2
5
Share

How to Adjust High Beam and Low Beam?

Low beam and high beam adjustment methods are as follows: The high beam can be switched to low beam by pushing the rotating lever towards the driver. There are lighting adjustment devices above the steering wheel. Push the switch towards the engine compartment position to keep the high beam on continuously; pull it back one gear to turn off the high beam and restore the low beam; push it one more gear towards the driver for a temporary high beam flash, and the switch will automatically return to the low beam position after releasing. Below is a partial introduction to car high and low beams: 1. Car lights should not be misused. Car lights include low beam, high beam, width indicator lights, headlights, fog lights, etc. Each light has its own specific purpose, and their use is quite particular—they should neither be misused nor neglected. 2. If lights are misused or not turned on during nighttime driving, it can cause inconvenience to both yourself and others, and even pose safety hazards, increasing the likelihood of accidents.
3
1
Share

Does the Ford Mondeo Have a Panoramic Sunroof?

The Mondeo is equipped with a panoramic sunroof. Below is an introduction to the functions of the Mondeo's sunroof: 1. It can quickly cool down the car. If you happen to park under the sun, the temperature inside the car in summer can easily reach above 60°C. Many drivers' first reaction is to turn on the air conditioning. However, it's actually better to open the windows and the sunroof first. While driving, the hot air can be quickly drawn out to achieve the cooling effect. This method cools the car about three times faster than using the air conditioning and saves a lot of fuel. 2. It can eliminate fog. During seasons with large temperature differences, if the side windows are closed while driving, the front windshield can easily fog up. In this case, the driver only needs to open the sunroof for a few seconds to quickly clear the fog. 3. It can quickly refresh the air inside the car. Opening the sunroof while driving can rapidly increase the air circulation speed inside the car, thereby improving ventilation and air exchange in the cabin.
9
3
Share

What kind of oil does Emgrand use?

Emgrand uses 5w30 oil, which has the functions of lubrication and wear reduction, auxiliary cooling, sealing and leakage prevention, rust and corrosion prevention, and shock absorption for the engine. Taking the 2020 Emgrand GS as an example, here is its introduction: 1. Suspension: The front suspension is MacPherson independent suspension, and the rear suspension is longitudinal trailing arm semi-independent suspension. 2. Power: It is equipped with a 1.4t turbocharged engine with a maximum horsepower of 141ps.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.