How to activate the child lock on a Golf?

2 Answers
TaliaLynn
09/03/25 8:25am
Volkswagen Golf's child safety lock switch is located on the side of the rear door. Open the door to see it. Here is an introduction to the Golf child lock: 1. Unlock the car: Unlock the car and open the corresponding rear door. 2. Insert the key into the slot: Position A turns off the child safety door lock, while position B activates it. 4. After the child safety door lock is activated: The rear door cannot be opened from the inside. 5. When locking the car: Never leave children or individuals requiring assistance alone in the car, as they may trap themselves inside. In an emergency, these individuals may not be able to exit the car or rescue themselves. Those trapped inside may suffer from extreme heat or cold within the vehicle.
Was this review help?
11
4
Share
DeKatherine
09/16/25 2:56am
I've been driving a Volkswagen Golf for ten years, and setting the child lock on the rear doors is quite simple. After opening the rear door, look for a small circular hole or a small toggle switch on the door frame edge, usually near the door lock close to the hinges. Use the small key that comes with the car to insert into the hole and turn it clockwise, or simply move the switch to the lock position by hand. A slight click sound indicates it's locked. Then, close the door and try pulling the handle from the inside to ensure it doesn't move—that means it's successful. Safety is crucial, especially when children are in the car. I often remind my neighbors to do the same to prevent kids from accidentally opening the door. The Golf's design is thoughtful, and the operation is effortless. I make it a habit to check the child lock every two weeks when washing the car to ensure it remains locked and avoids any risks.
Was this review help?
20
0
Share
Expand All
More Forum Discussions

What are the methods to deal with excessive carbon monoxide in car exhaust?

Clean the three-way catalytic converter. Once this component is clogged or too dirty, it will lose its ability to convert carbon monoxide. Check the dashboard for any engine warning lights. If the air-fuel ratio of the engine cannot stabilize, incomplete combustion may occur.
8
1
Share

What to Do When the Battery is Undercharged and Won't Charge?

Check if the fuse has poor contact and reconnect it. Replace the wiring. If the battery has been used for a long time, the electrolyte may decrease, and it needs to be refilled. Replace the battery.
1
3
Share

How to Shift to Neutral in an Automatic Transmission Without Starting the Engine?

Turn on the power without starting the engine. Press the brake pedal and shift the gear. First shift to N (Neutral) gear, then start the engine, and then shift to D (Drive) gear. Release the parking brake. Lift your foot off the brake pedal and start driving.
17
0
Share

What is the simplest way to reset a car's ECU?

Drive for a while to allow the car to reach normal operating temperature, then park and turn off the engine, shutting down all electrical devices in the car. Open the car's hood, locate the battery, and disconnect the battery's power cables. Wait for 10 minutes before reconnecting, then turn on the power without starting the engine and activate the car's electrical devices, waiting for 30 seconds. Remove the key, and the reset is successful.
12
5
Share

What are the starting and parking procedures for the Volvo XC40?

Make preparations before starting the car. Press the start button to start the engine while holding down the foot brake. Shift the gear to D (Drive), gently release the foot brake to move forward, and press the accelerator pedal if acceleration is needed. Press the foot brake to stop the car. Shift to P (Park) and turn off the engine.
5
3
Share

What is the voltage of the ABS sensor connector?

The voltage of the ABS sensor connector is 5V to 8V, with an output voltage of 650mV to 850mV. During actual measurement, due to the fault protection function of the electronic stability control module, the voltage cannot be sustained after unplugging the ABS sensor connector, so voltage data cannot be used as a judgment criterion. The ABS sensor is an important component of the ABS system. ABS can maintain the directional stability of the vehicle during braking while driving, shorten the braking time and distance, and effectively prevent wheel lock-up and uncontrolled skidding during emergency braking, thereby enhancing the vehicle's controllability and making driving safer.
18
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.