···
Log in / Register

How Quickly Can You Complete Subject Two and Subject Three?

4 Answers
DeAdaline
08/27/25 3:53am

The fastest time to complete both subjects is about half a month to one month. Below are detailed explanations: 1. Subject Two: Subject Two, also known as the small road test, is part of the motor vehicle driver's license assessment. It refers to the field driving skills test. For small vehicles (C1/C2), the test includes five mandatory items: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving through curves (commonly known as S-turns). Some regions may include a sixth item, such as high-speed card collection. 2. Subject Three: Subject Three includes the road driving skills test and the safety and civilized driving knowledge test. It is also part of the motor vehicle driver's license assessment and refers to the road driving skills and safety knowledge test for motor vehicle drivers. The content of the road driving skills test varies depending on the type of vehicle license being pursued.

Was this review help?
15
4
Share
VanColton
09/09/25 3:01am

When I was getting my driver's license, I happened to enroll in the summer intensive course. After passing the written test (Subject 1), the instructor arranged an extremely tight schedule. We practiced driving from 7 AM to noon every day, followed by mock tests in the afternoon, with no breaks even on weekends. There were only five days between Subject 2 (basic skills) and Subject 3 (road test), and including the waiting time for exam slots, I got my license in exactly 30 days. However, this required consistent daily practice and passing all tests on the first attempt without failures. This accelerated course was exhausting—I lost 5 pounds that month. If you failed and had to retake any subject, it would delay the process by at least half a month per subject.

Was this review help?
15
4
Share
Expand All
VonCorbin
10/23/25 3:49am

My cousin just got his driver's license last month, completing all four test sections (Subjects 1 through 4) in just twenty-eight days. He said the key is to schedule the tests in advance. You can apply for Subject 2 after practicing for ten hours, and Subject 3 can be scheduled after five days of practice. However, this is only possible when test slots are plentiful—he happened to take the tests during the off-peak season with no waiting lines. I'd advise against rushing too much, as it's quite dangerous for beginners to hit the road immediately. My driving instructor used to say it's better to scrape the curb a few times during practice than to pass too quickly and end up in an accident afterward.

Was this review help?
19
2
Share
Expand All
MatthewLynn
12/06/25 4:13am

For Subject 2 driving practice, a minimum of 10 days is required, and you must complete at least 10 training hours even if you learn quickly. Subject 3 can be taken right after practice, but the system enforces a 7-day waiting period. Factoring in the scheduling time for examiners, the fastest you can complete it is over 20 days. During peak exam periods, just waiting for an appointment can take half a month. When I took my Subject 3 test, the system malfunctioned, and I waited 4 hours for nothing. Now, new regulations also require 2 hours of traffic duty, all of which count as time costs.

Was this review help?
9
2
Share
Expand All
More Forum Discussions

Where is the air conditioning filter located in the Touareg?

The air conditioning filter in the Touareg is located behind the glove box. If you need to replace the air conditioning filter in the Touareg, here are the replacement steps: 1. Remove the glove box and take off the protective panel below the glove box. Gently pull the panel, as there is a connection wire for the footwell light behind it. Remember to disconnect the footwell light wire when removing the panel. 2. Remove the cover of the air filter by pressing the clips on both sides to take off the cover. 3. After removing the air filter cover, take out the old air filter and replace it with a new one. 4. Reinstall the cover and the protective panel, paying special attention to reconnecting the footwell light wire.
18
1
Share

Is it okay not to apply film on the front windshield?

It is acceptable not to apply film on the front windshield. The front windshield itself has the function of blocking ultraviolet rays, so applying film is optional. If you choose to apply film, it is essential to use genuine products from reputable brands. Low-quality films often fail to meet the required light transmittance standards, which can impair the driver's visibility. Below is some relevant information about applying film to the front windshield: 1. Genuine films from reputable brands tend to be more expensive, but it is advisable not to opt for cheap, low-quality films. Inferior films can release harmful gases when exposed to high temperatures, posing health risks. 2. Before applying the film, ensure the glass surface is thoroughly cleaned. Avoid rolling down the windows or washing the car for a week after application, as this may affect the film's adhesion.
2
5
Share

How often should the brake fluid be changed for an Audi A6?

Audi A6 brake fluid should be changed every 2 years or 40,000 kilometers. The method for changing the brake fluid in an Audi A6 is as follows: 1. First, open the cap of the brake fluid filler port and use a syringe to extract some of the old fluid. After filling with new fluid, lift the car and loosen the brake fluid drain screws near the four tires to allow the brake fluid to slowly drain out. 2. Lower the car and slowly add new fluid to the filler port to avoid air entering the brake lines. When only 1/3 of the brake fluid remains in the reservoir, quickly lift the car again. 3. Tighten the drain screws on all four tires and then lower the car. Fill the brake fluid reservoir to the top and secure the cap to complete the brake fluid change. When using brake fluid, note that different types and brands of brake fluid should not be mixed. If the fluid absorbs moisture or contains impurities, it should be replaced or filtered promptly; otherwise, it may lead to insufficient braking pressure and affect braking performance. If the vehicle's braking shows signs of pulling to one side, it is advisable to replace the brake fluid with a higher-quality product.
4
5
Share

What engine does the Bestune T99 use?

Bestune T99 is equipped with a 2.0-liter turbocharged engine across the entire lineup. The engine of the Bestune T99 delivers 224 horsepower and a maximum torque of 340 Nm. This engine can output its maximum power at 4500 to 5500 rpm and reach its peak torque at 1650 to 4500 rpm. The engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. More details are as follows: 1. The engine is paired with an 8-speed automatic transmission (8AT). The AT transmission offers smoother gear shifts and better reliability and durability. 2. The Bestune T99 adopts a MacPherson independent suspension at the front and a multi-link independent suspension at the rear. As a mid-to-large SUV, the vehicle boasts a bold exterior design and a spacious interior. 3. The dimensions of the Bestune T99 are 4800 mm in length, 1915 mm in width, and 1685 mm in height, with a wheelbase of 2870 mm. The exterior design of the Bestune T99 is very appealing, and the interior design caters well to the aesthetic preferences of young consumers.
2
0
Share

How to clean rust on brake discs?

Brake discs are round discs that rotate as the vehicle moves. When braking, the brake calipers clamp onto the brake discs to generate braking force, slowing down or stopping the vehicle. Brake discs offer effective braking performance and are easier to maintain compared to drum brakes. There are several types of brakes, including disc brakes, drum brakes, and air brakes. Older vehicles often feature front disc brakes and rear drum brakes, while many modern cars are equipped with disc brakes on both front and rear wheels.
17
4
Share

What Causes Squeaky Brake Pads?

The reasons for squeaky brake pads are: 1. The brake pad shims lack lubricant or are improperly installed; 2. Misaligned brake pad installation; 3. Product defects, such as inconsistent friction block dimensions, large metal particles on the surface, unbroken oxidation film, or inferior hard material composition; 4. Initially silent but suddenly noisy after driving - usually caused by small stones trapped in the brake pads. Brake pads (also called brake linings) are critical safety components in a vehicle's braking system, playing a decisive role in overall braking performance.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.