How Often to Replace Spark Plugs for GAC Honda Lingpai

1 Answers
MacEmmett
07/30/25 3:50am
GAC Honda Lingpai's spark plugs are generally replaced every 30,000 kilometers. Under normal maintenance conditions, spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the user manual. The following standards can be referenced for maintenance replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the engine hood, lift the plastic cover of the engine, and remove the high-voltage wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris such as leaves or dust and ensure they are thoroughly cleaned. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage wires in the firing order and secure the cover.
Was this review help?
7
4
Share
More Forum Discussions

What is the fuel consumption of the Cavalier?

The Cavalier has a fuel consumption of approximately 7.3 liters per 100 kilometers. Below are detailed introductions about it: 1. Introduction One: The English name of the Cavalier, "Cavalier," means "knight," originating from the historically popular compact model Chevrolet-Cavalier by General Motors in North America. 2. Introduction Two: The front face of the Cavalier adopts the Chevrolet family-style double-layer front grille, featuring a new "Gale" gradient texture inside the grille. 6. Introduction Three: The headlight assembly of this car is adorned with chrome trim and an innovative double-L-shaped LED strip daytime running light, which is standard across all models.
2
4
Share

What is the difference between Aston Martin DBS and DB11?

Aston Martin DBS has stronger power, while Aston Martin DB11 is more affordable. The differences between Aston Martin DBS and DB11 are as follows: 1. Power: The Aston Martin DBS is equipped with a 4.0T turbocharged engine with a maximum power of 533kw and a maximum torque of 900n.m. The Aston Martin DB11, on the other hand, is equipped with a 5.2T engine with a maximum power of 447kw and a maximum torque of 700n.m. The power configurations of the two are different. 2. Interior: The biggest difference between Aston Martin DBS and DB11 lies in the configurations between the two models. The Aston Martin DB11 features interior configurations such as adjustable suspension, rearview camera, power-folding mirrors, heated seats, touchscreen LCD central control panel, leather steering wheel, etc., which are not available in the Aston Martin DBS.
1
0
Share

Why can't the Kaiyi C3 use 92-octane gasoline?

Kaiyi C3 should use 92-octane gasoline, as this fuel grade is recommended in the vehicle's official user manual. In addition to checking the appropriate fuel grade in the user manual, the Kaiyi C3 also indicates the recommended gasoline grade on the fuel tank cap. Typically, the fuel grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92-octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95-octane gasoline. For higher compression ratios, 98-octane gasoline is recommended. However, with the application of new technologies, the compression ratio alone cannot determine the appropriate fuel grade. High compression ratio engines can also be tuned to use lower-octane gasoline due to factors like ignition timing, turbocharging technology, and Atkinson cycle technology. Generally, higher gasoline grades have higher octane ratings and better anti-knock properties. 92-octane gasoline contains 92% isooctane and 8% n-heptane, while 95-octane gasoline contains 95% isooctane and 5% n-heptane. Occasionally using the wrong gasoline grade in the Kaiyi C3 only requires switching back to the correct grade after consumption. However, long-term use of the wrong gasoline grade can have the following effects: Using a higher-octane gasoline in a vehicle designed for lower octane won't cause damage, but the increased octane rating alters the fuel's ignition point, leading to delayed combustion. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. Using lower-octane gasoline in a vehicle designed for higher octane can cause engine knocking. The significantly lower octane rating lowers the fuel's ignition point, causing premature ignition during the compression stroke. If combustion occurs before the spark plug fires, resistance is generated during the upward stroke. This resistance makes the engine run very unstably. Mild knocking only increases noise without significant engine damage, but severe knocking indicates serious engine conditions, affecting driving stability and causing abnormal wear on pistons and cylinders, potentially leading to cylinder scoring.
20
1
Share

What are the reasons for the Southeast DX3 not responding when starting?

Southeast DX3 not responding when starting has the following reasons: 1. Battery depletion: When the car battery is depleted, the car will have difficulty starting. There are many reasons for car battery depletion, such as lack of water in the battery, battery failure, prolonged use of air conditioning, etc. Especially in winter, when temperatures are lower, the car's power consumption is significantly higher than in other seasons, and the battery's capacity decreases due to the low-temperature environment, leading to difficulty in starting the vehicle. 2. Ignition system failure: The car ignition system's function is to provide high-voltage electricity to the spark plugs at the right time to ensure the car's normal operation. If the car does not start and the battery is ruled out as the cause, it is very likely that the car's ignition system has failed. 3. Engine carbon buildup: There is too much moisture in the gasoline, poor fuel quality, or poor sealing of the valve seat rings. 4. Starter aging: If the car starter is used for too long, it will age, leading to weak starting and difficulty in starting the car.
8
0
Share

What is the fuel tank capacity of the Jetta Spring?

The fuel tank capacity of the Jetta Spring is 55 liters. It is a compact car under the FAW-Volkswagen Jetta brand. In the same class of vehicles, the fuel tank capacity of the Nissan Sylphy is 55 liters, and the fuel tank capacity of the Volkswagen Santana is 52 liters. If the owner wants to know the remaining fuel level, they can observe the fuel gauge on the right side of the instrument panel, which is marked with E and F. When the pointer is close to E, it indicates that the fuel is almost empty, and when it is close to F, it indicates that the fuel level is sufficient. The maintenance of the fuel tank is as follows: Drain accumulated water and sediment from the fuel tank, and check for any oil leakage at the fuel pipe joints and switches. For fuel tank caps equipped with air valves and steam valves, also check whether the ventilation holes are clear. The filter screen at the fuel filler inlet should be kept intact to prevent impurities from entering the fuel tank during refueling, which could block the fuel lines. The sealing gasket of the fuel filler cap should also be intact to prevent fuel from overflowing during driving.
11
2
Share

What Causes the Jerking Sensation When Releasing the Accelerator?

Introduction to the causes of jerking sensation when releasing the accelerator in cars: 1. Engine oil passage blockage: The combustion of fuel is determined by the engine's ignition, intake, and fuel injectors, which are also the source of the engine's power. If the intake volume decreases, ignition weakens, or the amount of fuel injected reduces, the power will be insufficient, leading to a jerking sensation. 2. Jerking sensation when starting an automatic transmission car: When wanting to accelerate quickly while driving, you need to press the accelerator deeply. At this time, the automatic transmission will automatically downshift to increase the engine speed. When the speed reaches a certain level, it will upshift. After upshifting, because the speed will drop significantly, a relatively obvious jerking sensation will occur. This situation often occurs in automatic transmission models with fewer gears, such as 4-speed automatic models.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.