How often should the Verna's brake pads be replaced?

1 Answers
LeoLee
07/29/25 9:07pm
The Verna's brake pads should be replaced every 60,000 to 70,000 kilometers. The method for replacing the brake pads is as follows: 1. Open the engine compartment to check the brake fluid level to prevent overflow during the replacement process; 2. Remove the wheel where the brake is located; 3. Remove the bolts of the brake caliper and take out the brake pads; 4. Install the new brake pads, tighten the guide bolts, and complete the replacement. Taking the 2020 Verna as an example, it belongs to the compact car category, with body dimensions of: length 4300mm, width 1705mm, height 1460mm, a wheelbase of 2570mm, and a fuel tank capacity of 43 liters. The 2020 Verna is equipped with a 1.4L naturally aspirated engine, with a maximum horsepower of 95PS, a maximum power of 70kW, a maximum torque of 132.4Nm, and is paired with a 5-speed manual transmission.
Was this review help?
16
4
Share
More Forum Discussions

Does idling the car consume fuel?

Idling the car generally does not increase the load or consume much fuel. Below is some information about fuel consumption: 1. Introduction: It usually refers to the amount of gasoline consumed per 100 kilometers, which is a theoretical indicator of the vehicle. 2. Methods to reduce fuel consumption: The longer the car idles, the more fuel it consumes, so try to minimize idle time; avoid rapid acceleration, slamming the throttle, and driving at low RPMs. 3. Factors affecting fuel consumption: Various driving conditions such as acceleration, deceleration, braking, and engine idling, as well as load capacity, temperature, and whether the air conditioning is on, all have an impact.
19
3
Share

What material is best for car engine guards?

Engine guards made of aluminum alloy are preferable. Different types of guard materials have fundamentally distinct characteristics. Relevant explanations are as follows: 1. Composition: Engine guards are generally made of hard plastic, resin, iron, or aluminum alloy. 2. Classification: Aluminum alloy guards: The most cost-effective option, lightweight, high strength, and affordable, making them one of the top choices for consumers. Plastic guards: Low manufacturing cost and the lightest in weight. Plastic-steel and steel types: Mostly used on high-intensity off-road vehicles. Installing these types of guards on ordinary cars and urban SUVs may instead increase fuel consumption.
13
0
Share

What are the disadvantages of dry dual-clutch transmissions?

The disadvantages of dry dual-clutch transmissions are poor wear resistance and transmission overheating. Here are the specific details: 1. Poor wear resistance: In stop-and-go traffic conditions, the automatic transmission frequently shifts back and forth between first and second gears. The frequent operation of the clutch leads to increased heat generation. This is especially problematic during high summer temperatures when both the engine and transmission temperatures are elevated. 2. Transmission overheating: When the clutch overheats, it will display a high-temperature warning, and the transmission's protection program will activate, putting the vehicle into a protective mode where it cannot be driven. The vehicle can only continue to operate after the temperature has decreased.
15
4
Share

How to Deal with Gasoline in Engine Oil?

Possible reasons for gasoline entering the engine oil in a car: 1. Incomplete combustion of gasoline, where unburned gasoline flows along the cylinder wall into the crankcase. (It is recommended to check whether the spark plugs are firing normally and whether the engine is running smoothly). 2. There is a fuel leak in the gasoline line (it is recommended to check the fuel line). Common characteristics of gasoline and diesel engines are as follows: 1. Gasoline engines have relatively low noise, lower manufacturing costs, higher rotational speeds compared to diesel engines, and relatively small mass. 2. Diesel engines have higher thermal efficiency, better emission performance, and better economic performance compared to gasoline engines.
2
1
Share

What is the ground clearance of the CT6?

The ground clearance of the Cadillac CT6 is 15cm, which ensures good comfort and handling. Here are some details about this car: 1. Powertrain. It is equipped with a 2.0T inline 4-cylinder turbocharged engine, with a maximum horsepower of 237ps, a maximum torque of 350nm, a maximum power of 174kw, and is paired with a 10-speed automatic transmission. 2. Body dimensions. The Cadillac CT6 is a sedan with body dimensions of 5179mm in length, 1879mm in width, 1500mm in height, a wheelbase of 3109mm, a minimum ground clearance of 162mm, and a body weight of 2000kg.
18
0
Share

Where is the Changan Automobile Factory located?

Changan Automobile Factory is located in Beijing. Taking the 2021 Great Wall CS75 as an example, its body dimensions are: length 4650mm, width 1850mm, height 1715mm, with a wheelbase of 2700mm, a fuel tank capacity of 58 liters, a luggage compartment volume of 520 liters, and a body weight of 1600kg. The 2021 Great Wall CS75 features a MacPherson independent front suspension and a multi-link independent rear suspension. It is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 178PS, maximum power of 131kW, and maximum torque of 265Nm, paired with a 6-speed manual transmission.
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.