How Often Should the Transmission Fluid Be Changed for the RAV4?

How long does it take for a new car to break in before it can be driven on the highway?

A new car can be driven on the highway at any time during the break-in period. Precautions for driving on the highway include: 1. The driver and front-seat passenger should fasten their seat belts, and the driver should not answer phone calls; 2. Avoid sudden steering wheel movements while driving at high speeds; 3. Do not change lanes arbitrarily while driving. When changing lanes or overtaking the vehicle in front, the turn signal must be activated in advance; 4. When overtaking, only the adjacent lane is allowed. After overtaking, the vehicle should immediately return to the driving lane and must not straddle or drive on the lane divider; 5. Do not reverse, drive in the opposite direction, cross the central divider to make a U-turn or turn, conduct test drives, or drive a training vehicle. Overtaking and parking on ramps are prohibited; 6. Maintain a following distance of at least 100 meters. When the speed is below 100 km/h, the distance from the vehicle in front in the same lane can be appropriately reduced, but the minimum distance should not be less than 50 meters.

16

1

Share

Is the Left Overtaking Always Fully Responsible?

Left overtaking is not necessarily fully responsible, it depends on the actual situation. Here are some precautions about overtaking: 1. No overtaking: Overtaking is not allowed in special road sections such as intersections, narrow bridges, curves, steep slopes, and tunnels. If a collision occurs with other vehicles while overtaking in these sections, you will be fully responsible. Also, when the vehicle ahead is turning left, making a U-turn, or overtaking, overtaking is not allowed. In case of an accident, you will also be fully responsible. 2. Meeting vehicles: While driving, there are often vehicles coming from the opposite direction. If you encounter vehicles from the opposite direction, overtaking is not allowed. In case of a collision, you will be fully responsible. Also, when the vehicle ahead is a fire truck or ambulance, overtaking is not allowed.

15

1

Share

How to Adjust the Idle Speed of a Scooter?

Generally, turning the screw clockwise can increase the idle speed of the scooter, while turning it counterclockwise can decrease the idle speed. Here are some related introductions: 1. Introduction one: The adjustment of the air-fuel mixture and idle speed should be done after the engine is warmed up. It is relatively normal for the idle speed to be unstable when the engine is cold. 2. Introduction two: The idle speed of scooters is usually slightly higher than that of other models, reaching around 1600 RPM is considered normal. Additionally, the starting RPM for scooters generally needs to reach 3000 RPM. 3. Introduction three: If the idle speed is noticeably unstable with significant fluctuations, you can clean the air filter and carburetor, and check if the valve clearance is too small. Also, inspect whether the intake pipe between the carburetor and the engine, the suction pipe of the vacuum fuel tank switch, and other rubber hoses of the carburetor have aged or are leaking air.

11

0

Share

What is the installation method for a front and rear dual-camera dash cam?

The installation method for a front and rear dual-camera dash cam is as follows: 1. Connect the power supply and start routing the wires; 2. Insert the wires from left to right into the ceiling; 3. Route the wires to the upper right corner and towards the door, then forcefully pry open the side panel to insert them; 4. Run the wires downward along the B-pillar; 5. At the door edge, peel back the door seal and insert the wires; 6. Continue routing the wires downward along the seal; 7. Remove the floor mat and run the wires underneath it; 8. Plug the dash cam into the cigarette lighter to automatically power it on; 9. Turn off the device and begin routing the wires; 10. Insert the wires from left to right into the ceiling, then pry open the corner cover; 11. Route the wires along the gaps all the way to the rear; 12. Route the wires along the window towards the rear, pry open the seal, and insert the wires; 13. Attach the rear camera to the rear windshield and adjust the angle; 14. Align the wires and connect the rear camera power cable; 15. Finally, conceal the wires.

16

5

Share

How long after the car loan is paid off can the vehicle be transferred?

The bank will release the mortgage and return the green title to the owner after the car loan is fully paid off. Then, the owner needs to take the green title to the vehicle management office to complete the mortgage release procedure. Required documents: 1. Original and photocopy of the vehicle owner's identity proof (for organizational vehicles, the original and photocopy of the organization code are required, and temporary residents also need to provide the original and photocopy of a valid residence permit); 2. Identity proof of the mortgagee (must be stamped with an official seal); 3. Power of attorney from the mortgagee (stamped with an official seal and verification seal); 4. If an agent is involved, the original and photocopy of the agent's identity proof and the power of attorney are also required; 5. Vehicle registration certificate; 6. Fill out the "Application Form for Mortgage Registration or Pledge Filing of Motor Vehicles". Procedure: Go to the comprehensive service window at the vehicle management service center hall to complete the process.

7

0

Share

Can You Refuse to Take Delivery of a Car Older Than 3 Months?

You can refuse to take delivery of the car. After placing an order for a motor vehicle, you can request that the production date of the vehicle must fall within a specified time frame. If it exceeds this period, you have the right to refuse delivery. Below are specific details about vehicle delivery inspection: 1. Check the vehicle's paint: Inspect for any scratches or wear on the paint. Observe under ample sunlight to check for color discrepancies. Open the doors and adjust them to various angles to examine the sheet metal for smoothness under different lighting conditions. 2. Inspect the bodywork: Examine the gaps between components such as the front hood, doors, fuel cap, taillights, and headlights to ensure they are even. Uneven gaps may indicate that parts have been replaced. 3. Check the vehicle's identification plate: The vehicle's identification plate is located on the side of the driver's door or inside the engine compartment. Verify that the VIN (Vehicle Identification Number) matches. 4. Assess the vehicle's wear: Check if the tire tread hairs are intact and inspect the undercarriage for any signs of scraping.

8

4

Share

How Often Should the Transmission Fluid Be Changed for the RAV4?

How long does it take for a new car to break in before it can be driven on the highway?

Is the Left Overtaking Always Fully Responsible?

How to Adjust the Idle Speed of a Scooter?

What is the installation method for a front and rear dual-camera dash cam?

How long after the car loan is paid off can the vehicle be transferred?

Can You Refuse to Take Delivery of a Car Older Than 3 Months?

Can a vehicle pass inspection with different tire tread patterns?

Should You Go for Driving Practice in the Rain?

What is the displacement of 652t?

What lights should be turned on in advance when a motor vehicle makes a U-turn?