How often should the spark plugs of Tiggo 3 be replaced?

1 Answers
LaElaina
07/29/25 11:52pm
Tiggo 3 spark plugs should be replaced every 30,000 kilometers. The spark plug is a crucial component of the gasoline engine ignition system. It introduces high-voltage electricity into the combustion chamber and generates a spark by jumping the electrode gap, thereby igniting the combustible mixture in the cylinder. If the spark plug is damaged, it can directly cause issues such as leakage in the vehicle's ignition system, increased fuel consumption, reduced power, and most importantly, difficulty in ignition, affecting the normal operation of the vehicle. Severe erosion of the spark plug, such as scarring at the top, damage, or melted and eroded electrodes, indicates that the spark plug is damaged and should be replaced. Steps for replacing spark plugs: Open the engine hood, lift the plastic cover of the engine, and remove the high-voltage distributor wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for external debris like leaves or dust and ensure they are thoroughly cleaned. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage distributor wires according to the ignition sequence and secure the cover.
Was this review help?
19
5
Share
More Forum Discussions

How to Tell if a Manual Transmission Has Water Intrusion?

Signs of water intrusion in a manual transmission include: 1. Rust: If some screws inside the transmission show rust, this indicates mild water intrusion with relatively low water content. In this case, simply replace the gaskets, oil seals, friction plates, etc. It's also advisable to change the transmission fluid and differential oil. 2. Deposits: If a white polymer deposit is found on the oil pan, this signifies moderate water intrusion. A complete replacement of gaskets, oil seals, friction plates, and other components is necessary, along with the automatic transmission fluid and differential oil. Additionally, if water has reached components like the automatic transmission multifunction switch, those should also be replaced.
6
3
Share

What is an SNSR fuse?

SNSR is just a general term for automotive sensor-type fuses. Here are the relevant details: 1. Definition: A fuse, officially called a 'circuit breaker,' serves a similar purpose in cars as it does in homes. When the circuit current is abnormal and exceeds its rated current, the fuse melts to act as a protective barrier for the circuit. 2. Common fuses: Automotive fuses can be categorized into high-current fuses and medium-low current fuses. The ones most commonly encountered are medium-low current fuses. Medium-low current fuses can be further divided into blade fuses, plug-in fuses, screw-in fuses, tubular fuses, and flat fuses.
10
1
Share

How to Deal with ESC (Electronic Stability Control) Malfunction?

When encountering an ESC (Electronic Stability Control) malfunction, it is necessary to have the repair personnel at a 4S dealership use a computer to diagnose the cause of the issue before proceeding with the relevant repairs. Below is some related information about ESC malfunctions: 1. Definition: An ESC system malfunction refers to a failure in the Electronic Stability Control system, which is an electronic vehicle stability control system. This system activates during vehicle turns and enhances driving stability. 2. ESC System Operational Requirements: The ESC system relies on numerous sensors to function properly. If certain sensors malfunction, it can affect the normal operation of the ESC system.
15
3
Share

What is the function of the R gear?

The function of the R gear is to enable the vehicle to move in the opposite direction, achieving the function of reversing. The following is a related introduction to automatic transmission gears: 1. N gear: Neutral gear, used for temporary parking. 2. P gear: Parking gear, used when the engine is turned off and the car is stationary. When the vehicle stops, the gear must be shifted into P gear before the power can be turned off, the key can be removed, and the doors can be locked. 3. L gear: Low gear, also known as the climbing gear, its function is to reduce speed and increase torque. 4. S gear: Sports mode, whether it's climbing a slope or quickly overtaking, the S gear can be used.
19
5
Share

Can I wait at a red light in a right-turn and straight lane?

If the right-turn and straight lane is a combined lane, you can wait at a red light when encountering one. Here are the relevant details: 1. Left turns: When turning left, the vehicle should turn from the left side of the intersection center point. Turn signals should be activated during the turn, and low beams should be used when driving at night. 2. Traffic signals: When encountering a green light, vehicles should proceed in order; when encountering a red light, they should stop in sequence behind the stop line. For lanes without a stop line, stop before the intersection. 3. Right turns: When turning right and encountering a vehicle in the same lane waiting for a green light, stop and wait in sequence.
1
4
Share

How many kilometers do commercial vehicles need to be scrapped?

Different commercial vehicles have different mileage requirements for scrapping. Here are the relevant details: 1. Taxis: Small and mini taxis are scrapped after 600,000 kilometers, medium-sized taxis after 500,000 kilometers, and large taxis after 600,000 kilometers. 2. Passenger training vehicles: Small and medium-sized passenger training vehicles are scrapped after 500,000 kilometers, and large passenger training vehicles after 600,000 kilometers. 3. Other passenger commercial vehicles: Other small and mini passenger commercial vehicles are scrapped after 600,000 kilometers, medium-sized ones after 500,000 kilometers, and large ones after 800,000 kilometers.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.