How often should the spark plugs be replaced on a BMW 5 Series?

1 Answers
Alan
07/25/25 1:36am
BMW 5 Series spark plug replacement interval: Under normal maintenance conditions, replacement is recommended every 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it's advisable to follow the user manual. You can refer to the following standards for maintenance replacement: Platinum spark plugs should be replaced at 40,000 km, ordinary nickel alloy spark plugs at 20,000 km, and iridium spark plugs at 60,000-80,000 km. Spark plug working principle: The spark plug's ground electrode is connected to the metal shell, which is threaded into the engine block through the cylinder head. The insulator primarily serves to isolate the metal shell from the center electrode. The terminal nut is the part of the spark plug that contacts the high-voltage coil. When current passes through the terminal nut and center electrode, it ionizes the medium between the center electrode and ground electrode to produce a spark, thereby igniting the air-fuel mixture in the cylinder.
Was this review help?
10
5
Share
More Forum Discussions

How to Eliminate Car Audio Resonance?

There are two methods to eliminate car audio resonance: 1. Adjust the main volume of the equalizer to approximately 75%. 2. After ensuring the amplifier is installed correctly, set the volume of the head unit and amplifier to the minimum, then test the following functions by adjusting the crossover points: (1) Set the front speaker amplifier's crossover switch to high-pass, with the crossover point between 80Hz-120Hz. (2) Set the rear speaker amplifier to high-pass as well, with the crossover point between 200Hz-400Hz. (3) Set the subwoofer amplifier's crossover switch to low-pass, with the crossover point between 80Hz-120Hz. (4) Turn off or reset the bass frequency enhancers on all amplifiers to zero.
6
5
Share

Where is the engine number of the Highlander located?

The engine number of the Highlander is located at the connection point between the engine and the transmission. The vehicle uses two engine models: 8AR and 2AR. The 8AR refers to an inline four-cylinder engine, while the 2AR refers to a V-type six-cylinder engine. The engine number serves as the engine's identification, as it contains information that the manufacturer labels according to automotive industry regulations. Every vehicle has a corresponding engine number. Taking the 2020 Highlander as an example, it is a mid-size SUV with the following dimensions: length 4890mm, width 1925mm, height 1715mm, a wheelbase of 2790mm, and a fuel tank capacity of 72.5 liters.
6
0
Share

What are the reasons for changes in the technical condition of a car?

Reasons for changes in the technical condition of a car: The alteration in the technical state of car components, mechanisms, or assemblies is the fundamental cause of changes in a car's technical condition. Factors such as natural wear, plastic deformation, fatigue damage, corrosion, and other changes in parts or materials directly affect the alteration of a car's technical condition. Relevant information about car maintenance is as follows: 1. Introduction: Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of a car, also known as car servicing. 2. Maintenance scope: Modern car maintenance mainly includes the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, and other maintenance areas.
3
3
Share

What are the reasons for both low beam lights of Refine not working?

Regarding the reasons and solutions for both low beam lights of Refine not working: 1. Light failure: Poor contact of the lamp head, failure of the car fuse or relay, or the fuse being replaced with a direct wire connection or twisted wire causing a short circuit. Solution: Check the lights, fuse, and relay, and repair or replace them. 2. Water ingress in the lights: The lights should not be submerged in water. While driving, water splashing from the front generally does not affect the lights, but when washing the car, opening the front hood and using a high-pressure water gun to wash the engine and lights can easily cause water ingress. Solution: Remove the lights for cleaning or replacement.
17
1
Share

What is the actual fuel consumption per 100 kilometers for the Audi A5?

The actual fuel consumption per 100 kilometers for the Audi A5 is 7.6 liters. Taking the 2021 Audi A5 as an example, it belongs to the mid-size car category with the following dimensions: length 4757mm, width 1843mm, height 1358mm, wheelbase 2826mm, fuel tank capacity 54 liters, trunk capacity 480 liters, and curb weight 1640kg. The 2021 Audi A5 features a five-link independent suspension both in the front and rear. It is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 204PS, maximum power of 150kW, and maximum torque of 320Nm, paired with a 7-speed dual-clutch transmission.
5
1
Share

What are the effective measures to prevent vehicle failure?

To effectively prevent brake failure in motor vehicles, it is necessary to regularly maintain the brake system; check the free travel of the brake pedal before driving; use the brakes correctly to prevent thermal fade; for vehicles with hydraulic brakes, check for any leakage of brake fluid before driving. Relevant information about braking is as follows: 1. Introduction: Refers to the action of stopping or reducing the speed of running locomotives, vehicles, other transport tools, or machinery. 2. Principle: The general principle of braking is to fix a wheel or disc on the high-speed shaft of the machine and install corresponding brake shoes, bands, or discs on the machine base to generate braking torque under external force.
3
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.