How often should the spark plugs be replaced in the new Crown?

2 Answers
MacDerek
09/05/25 5:17am
The spark plugs in the new Crown should be replaced every 60,000 kilometers. Spark plugs are a crucial component of the gasoline engine's ignition system, responsible for introducing high-voltage electricity into the combustion chamber and creating a spark by jumping the electrode gap, thereby igniting the combustible air-fuel mixture in the cylinder. The dimensions of the new Crown are 4910mm in length, 1800mm in width, and 1455mm in height, with a wheelbase of 2920mm. The Crown is equipped with three engine options: 2.5L, 3.0L, and 4.3L. The first two are V6 24-valve designs, while the 4.3L engine is a V8. The engines feature the Dual VVTi system, which intelligently varies the timing of both intake and exhaust valves, significantly improving the engine's air intake efficiency, fuel economy, and power performance, resulting in stronger horsepower. The chassis is equipped with a four-wheel fully independent suspension system.
Was this review help?
14
5
Share
LaJocelyn
09/17/25 5:42am
The replacement interval for Toyota Crown spark plugs should be determined based on the specific recommendations in the manual. Generally, most models recommend replacement every approximately 60,000 kilometers, but the type of spark plug is also crucial. Platinum or iridium spark plugs can last up to 100,000 kilometers, while standard copper ones might need replacement as early as 40,000 kilometers. Worn-out spark plugs can lead to common issues like difficulty starting the engine or sudden increases in fuel consumption—I've encountered many such cases when helping friends inspect their cars. Delaying replacement may also contribute to engine wear. It's best to have the technician check the electrode gap during routine maintenance; if it's too wide, it's time for a replacement. The replacement process is actually straightforward and costs just a few dozen dollars. Don't wait until they fail to address the issue, as that could result in higher repair costs and potentially compromise driving safety. Regular maintenance is a good habit for extending your vehicle's lifespan.
Was this review help?
18
0
Share
Expand All
More Forum Discussions

What is the China VI Engine Oil Certification Standard?

Automobile manufacturers stipulate that China VI models equipped with particulate filters must use medium/low ash engine oil, such as ACEA-C series, GM-dexos1 series, VW50800/50900 series, etc. Relevant information about engine oil is as follows: 1. Introduction: Engine oil, also known as engine lubricant (English name: Engine-oil), with a density of approximately 0.91×10³ (kg/m³), serves to lubricate and reduce friction, assist in cooling, seal against leaks, prevent rust and corrosion, and dampen vibrations in the engine. It is hailed as the "blood" of automobiles. 2. Composition: Engine oil consists of base oil and additives. Base oil is the main component of lubricating oil, determining its fundamental properties, while additives compensate for and improve the shortcomings of base oil performance, endowing it with certain new characteristics, making them an essential part of lubricating oil.
1
0
Share

Does Volkswagen use 92 or 95 octane gasoline?

Volkswagen uses 95 octane gasoline. Gasoline grade: Gasoline grade refers to the octane number, which indicates the anti-knock performance. The higher the octane number, the better the anti-knock performance. Octane value: Each type of gasoline has a different octane value and anti-knock performance. This is mainly because the higher the engine's compression ratio, the higher the pressure and temperature inside the cylinder, making it more prone to engine knocking. The appropriate gasoline grade for each car depends on its compression ratio. For turbocharged engines, it is recommended to use higher-grade gasoline. Various gasoline grades are actually formulated to meet the needs of engines with different compression ratios.
15
2
Share

What are the effects of thin brake pads?

Thin brake pads may cause damage to the brake discs. The most severe consequence could be brake failure. Potential issues caused by thin brake pads: Abnormal noises may occur when braking during normal driving; The pedal travel distance may become longer when braking during normal driving; It may cause damage to the brake discs; The most severe consequence could be brake failure. Service life of brake pads: The service life of front brake pads is approximately 20,000-40,000 kilometers, while rear brake pads last about 60,000-100,000 kilometers. Typically, a new set of brake pads is about 1.5cm thick. During use, as the calipers and pads wear down, the pads gradually become thinner. When the visible thickness reduces to about 0.5cm, the brake pads should be replaced immediately.
2
0
Share

Is Full Vehicle Soundproofing Modification Noticeably Effective?

Improvement is very noticeable, mainly by effectively addressing engine noise, road noise, tire noise, wind noise, and body structure noise for significant results. Below are common classifications of automotive noise: 1. Engine noise: The vehicle's engine is a source of noise, varying with different engine speeds. 2. Road noise: Road noise is formed when the vehicle is driving at high speeds, with wind cutting in creating noise and the driving motion causing chassis vibrations. Additionally, gravel impacting the vehicle's chassis on the road also generates noise, which are the main sources of road noise. 3. Tire noise: Tire noise is produced by the friction between the tires and the road surface during high-speed driving. The level of tire noise depends on road and vehicle conditions; worse road conditions lead to louder tire noise. Moreover, there is a significant difference in tire noise between asphalt and concrete road surfaces.
1
4
Share

How Much Horsepower Does Reducing a Car's Weight by 100 Jin Equal?

Reducing a car's weight by 100 jin is equivalent to increasing the engine power by 10 horsepower. Below are specific details about vehicle horsepower: 1. Concept: Horsepower is a measure of power, with achievement rates typically expressed as a percentage (%), indicating the degree to which actual values meet target values (the extent to which goals are achieved). 2. Origin: 'Horsepower' is a unit of power, commonly seen on diesel engines and steam turbines marked with the term 'horsepower'. Over 200 years ago, engineers, based on the designs of the Englishman James Watt, produced the world's first batch of improved steam engines. 3. Horsepower Conversion: Horsepower is a commonly used unit for measuring power in engineering technology, proposed by James Watt. 1 horsepower is approximately equal to 735 watts. Generally, it refers to metric horsepower rather than imperial horsepower.
16
4
Share

Will water entering the car's air intake affect the engine?

Yes, it will have an impact. A small amount of water may enter the engine and mix with the engine oil, degrading the oil quality. Oil containing water can increase wear on engine components, potentially leading to increased engine noise and vibration during future driving. Below are precautions for driving through water: 1. Drive in a low gear: Use a low gear (for automatic transmission vehicles, engage the hill-climbing gear) and slowly drive through the water at a steady speed while maintaining control of the steering wheel. Be aware of any potholes or gaps beneath the water on the road. 2. Do not restart the engine after stalling: If the vehicle stalls in a waterlogged area, do not attempt to restart the engine. Engine stalling indicates that water has already entered the cylinders. Restarting the engine can cause severe damage due to the incompressibility of water, potentially bending or breaking the piston connecting rod components and, in severe cases, leading to complete engine failure.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.