How Often Should the Original Spark Plugs of the Tenth-Generation Civic Be Replaced?

2 Answers
EloiseRose
07/24/25 9:23am
The replacement interval for the original spark plugs of the tenth-generation Civic mainly depends on the mileage. It is recommended to replace the spark plugs once every 40,000 to 60,000 kilometers. Spark plugs are a crucial component of the gasoline engine's ignition system. They introduce high-voltage electricity into the combustion chamber and generate sparks by jumping the electrode gap, thereby igniting the combustible air-fuel mixture in the cylinder. Steps for replacing spark plugs: Open the hood, lift the engine's plastic cover, and remove the high-voltage wires. Mark the position of each cylinder to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris like leaves or dust and ensure they are thoroughly cleaned. Place the new spark plugs into the spark plug holes, hand-tighten them a few turns, and then use the socket to tighten them further. Reinstall the removed high-voltage wires according to the firing order and secure the cover.
Was this review help?
17
5
Share
DallasFitz
08/11/25 4:46am
I've been driving for over a decade and have repaired many Civics. For the 10th-gen Civic, the factory-recommended spark plug replacement interval is generally around 100,000 kilometers, as suggested in most owner's manuals. Spark plugs are crucial ignition components. Over time, their electrodes wear out or accumulate carbon deposits, which can reduce ignition efficiency, leading to engine vibration and increased fuel consumption. I recommend paying attention to driving habits – in urban traffic jams or during aggressive acceleration, spark plugs wear out faster. Consider inspecting or replacing them earlier, roughly every 80,000 to 100,000 kilometers. While factory parts are durable under normal driving conditions, don't wait for a failure to occur. Otherwise, you might experience rough driving or even stalling. During routine maintenance, have a mechanic test them – it can save you a lot of hassle.
Was this review help?
1
0
Share
Expand All
More Forum Discussions

What are the differences between the Lynk & Co 03 1.5T and 2.0T?

The differences between the Lynk & Co 03 1.5T and Lynk & Co 03 2.0T are: 1. Different transmissions: the Lynk & Co 03 1.5T is matched with a 6-speed manual or 7-speed dual-clutch transmission; the Lynk & Co 03 2.0T is matched with a 6-speed automatic transmission. 2. Different maximum power: the maximum power of the Lynk & Co 03 1.5T is 132kW; the maximum power of the Lynk & Co 03 2.0T is 140kW. Both the Lynk & Co 03 1.5T and Lynk & Co 03 2.0T have front-wheel drive, MacPherson independent front suspension, multi-link independent rear suspension, and electric power steering.
14
2
Share

Where should the registration take place when a motor vehicle is used as collateral for a mortgage?

The owner of a motor vehicle who uses the vehicle as collateral for a mortgage should apply for mortgage registration with the traffic management department of the public security authority where the vehicle is registered. Introduction to motor vehicle mortgage loans is as follows: Definition: A car mortgage loan is a loan obtained from a financial institution or auto consumer loan company using the borrower's or a third party's car or self-purchased vehicle as collateral. The primary purpose of using a car as collateral for a loan is for quick capital turnover. Notes: Most car mortgage loans follow the practice of securing the loan with the vehicle's documents rather than the vehicle itself, meaning that by mortgaging the relevant documents of the car to the lending institution, one can obtain the loan, while the car can still be used normally after installing a GPS. Therefore, before processing the mortgage, it is advisable to first understand whether the car mortgage involves the physical vehicle, to try and avoid institutions that require the vehicle to be impounded.
6
3
Share

What to Do When a Car Battery Doesn't Hold Charge?

Solutions for a car battery that doesn't hold charge: 1. Add distilled water or purified water to the battery; tap water must not be used. 2. Use a repair device's high-resistance repair function to raise the voltage above 11V. 3. If the battery voltage is below 10V and cannot be increased through charging or repair, the battery must be replaced. 4. For cases of electrode sulfation or battery aging, it is also recommended to replace the battery as soon as possible. A car battery, also known as a storage battery, is a type of battery that works by converting chemical energy into electrical energy. The commonly referred-to car battery is a lead-acid battery, which is primarily made of lead and its oxides, with sulfuric acid solution as the electrolyte.
3
2
Share

What is the tire pressure for 300kpa?

Tire pressure of 300kpa is equivalent to 3.0bar. Generally, the normal tire pressure for car tires ranges between 2.30bar and 2.5bar. However, the specific recommended tire pressure should be based on the manufacturer's guidelines, which can usually be found in the vehicle's user manual, on the label near the driver's side door (B-pillar), in the drawer next to the driver's seat, or on the fuel tank cap. Tire pressure standards also depend on the type of tire and the vehicle model. Different models have varying weights, heights, and tire sizes, which require different tire pressures. Standard tires typically have a pressure range of 2.40bar to 2.5bar, while reinforced tires range from 2.80bar to 2.90bar.
17
2
Share

Is the P0017 fault code caused by a skipped tooth?

P0017 fault code does not necessarily mean a skipped tooth. The P0017 fault code indicates an unreasonable correlation between the crankshaft position and the exhaust camshaft position. There are multiple causes for this fault code, and a skipped tooth is just one of them. Causes of the P0017 fault code: 1. Abnormal oil pressure; 2. Stuck VVT solenoid valve; 3. Faulty VVT actuator; 4. Chain skipped tooth or tensioner pressure loss; 5. Faulty camshaft and crankshaft position sensors or signal disc; 6. Damaged ECU. Solutions for the P0017 fault code: 1. Check if the crankshaft position signal disc is dirty or damaged, and clean or replace it if necessary; 2. Swap the intake and exhaust VVT solenoid valves and camshaft sensors; 3. Remove the timing chain and replace both VVT gears.
16
4
Share

Why does the parking sensor keep beeping when there is nothing there?

The reasons why the parking sensor keeps beeping when there is nothing there are: 1. The sensor hole is too small, too tight, or installed on an iron or hard protective bumper; 2. There are attachments such as paint, snow, or ice on the sensor surface; 3. Poor sensor characteristics or excessively low working environment temperature; 4. Sensor malfunction. The solutions for a continuously beeping parking sensor are: 1. Wipe the parking sensor; 2. Check the parking sensor alarm end for any abnormal wiring; 3. Replace faulty or damaged components. The parking sensor is a safety auxiliary device for parking or reversing a car. It can inform the driver of the surrounding obstacles through sound or a more intuitive display, eliminating the troubles caused by the driver's need to look around when parking, reversing, or starting the vehicle, and helping the driver overcome blind spots and unclear vision.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.